A. Safety Lock
B. See safety instructions
C. Pull-out bin
D. Casters
E. Paper/card entry
Will shred: Paper, staples and plastic credit cards
Will not shred: CD/DVDs, adhesive labels, continuous form paper, transparencies,
newspaper, cardboard, paper clips, laminates, file folders, X-rays or plastic other than
noted above
Paper/card shred size:
Micro-Cut .................................................................7/64 in. x 25/64 in. (3mm x 10mm)
Maximum:
Sheets per pass ........................................................................................................... 10*
Cards per pass............................................................................................................... 1*
Paper entry width........................................................................................9 in. (223mm)
*8.5”x11”, 20lb., (75g) paper at 120V, 60Hz, 3.5Amps; heavier paper, humidity or other
than rated voltage may reduce capacity. Maximum recommended daily usage rates: 150
sheets per day; 10 credit cards 10 sheets per pass to avoid jams.
CAPABILITIES
ENGLISH
Model 62MC
KEY
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
• Operation, maintenance, and service requirements are covered in the instruction
manual. Read the entire instruction manual before operating shredders.
• Keep away from children and pets. Keep hands away from paper entry. Always set
to off or unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder
openings. If object enters top opening, switch to Reverse ( ) to back out object.
• DO NOT use aerosol products, petroleum based or aerosol lubricants on or
near shredder. DO NOT USE “CANNED AIR” OR “AIR DUSTERS” ON SHREDDER.
Vapors from propellants and petroleum based lubricants may combust causing
serious injury.
• Do not use if damaged or defective. Do not disassemble shredder.
Do not place near or over heat source or water.
• Avoid touching exposed cutting blades under shredder head.
• Shredder must be plugged into a properly grounded wall outlet or socket of the
voltage and amperage designated on the label. The grounded outlet or socket
must be installed near the equipment and easily accessible. Energy converters,
transformers, or extension cords should not be used with this product.
• FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.
• For indoor use only.
• Unplug shredder before cleaning or servicing.
F. Control Panel and LEDs
1. Reverse
2. ON/OFF (green)
3. Forward
4. Overheat (red) and
Remove paper (yellow)
5. Bin open (yellow)
To set lock slide
button down
PRODUCT MAINTENANCE
All micro-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding, and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
*Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
Go to Support Section at www.fellowes.com or see back page of manual for useful
telephone numbers.
D.
A.
C. F.
E.
B.
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This
indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about
the continuous operation and recovery time for this shredder.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
TROUBLESHOOTING
Shredder doesn’t start:
Make sure switch is in on position ( ).
Make sure safety lock is in unlock position.
Make sure bin is closed.
Check for jam.
Remove and empty bin.
Wait 60 minutes for motor to cool down.
PAPER JAM
Alternate slowly back and forthSet to Reverse ( )
for 2-3 seconds
Set to Off ( )
and unplug
Gently pull uncut
paper from paper
entry. Plug in
Set to Auto-On ( )
and resume shredding
5
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of
defects in material and workmanship and provides service and support for 1 year from the date
of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to
be free from defects in material and workmanship for 1 year from the date of purchase by the
original consumer. If any part is found to be defective during the warranty period, your sole and
exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective
part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product
usage standards, shredder operation using an improper power supply (other than listed on
label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any
additional costs incurred by Fellowes to provide parts or services outside of the country where the
shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION
TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable
for any consequential or incidental damages attributable to this product. This warranty gives you
specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide,
except where different limitations, restrictions, or conditions may be required by local law. For
more details or to obtain service under this warranty, please contact us or your dealer.
LIMITED PRODUCT WARRANTY
1 32 4 6
23
*Apply oil across entry
2
Set to Reverse ( )
for 2-3 seconds
Set to Off ( )Set to Off ( )
3
14
BASIC SHREDDING OPERATION
Continuous operation:
Up to 7-minutes maximum
NOTE: Shredder runs briefly after each pass to
clear entry. Continuous operation beyond 7-minutes
will trigger 60-minute cool down period.
Safety Lock prevents accidental operation. To set, wait for shredding to stop, set control switch to Off (O) position, then slide black button down.
To unlock, slide black button up. For greater safety, always unplug shredder after use.
PAPER/CARD
Plug in and set to
Auto-On ( )
Feed paper/card
straight into paper
entry and release
2
When finished shredding,
set to Off ()
13
BASIC SET UP
CASTER INSTALLATION
1
3
42
