FENDT FAVORIT 900 Instruction manual

WERKSTATTHANDBUCH
WORKSHOPMANUAL
MANUEL D´ATELIER
MANUAL DE TALLER
MANUALE PER I´OFFICINA
FAVORIT 900
916 chassis no. 23/3001 and up
920 chassis no. 23/3001 and up
924 chassis no. 23/3001 and up
926 chassis no. 23/3001 and up
Note:
If not noted otherwise, is the document valid for the North-America
version also (chassis no. 9xx/24/xxxx)
Ausgabe 12/2001 Edition
Xaver FENDT GmbH & CO.
Ein Unternehmen der AGCO-Corp.
Maschinen- und Schlepperfabrik, Marktoberdorf / Bayern Germany
Postfachadresse: D-87609 Marktoberdorf, Postfach 1155
Telefon [phone] Telefax (0 83 42) 77-2 22 (Kundendienst)
Bestell-Nr. / order no. / no. De comande / no. Die ordinazione
X 990.005.040.010 en
2711C - en

Farmer 400
Fav 700
Fav 900
Tractor / General system
Assembly overview A
General
04/2000 0000 000009
A
b1/4 Capitel Docu-No.
Index
Date Version Page Assembly overview
Text-module
Text-module
Text-module
0000 Tractor / General system
1000 Transmission
1005 Transmission control unit
1010 Differential
1015 Axle drive
1030 Handbrake
1050 Housing
1070 Brake system
1080 Vario transmission unit
1090 Emergency control
1100 Clutch actuation system
1150 Cardan brake
1170 ML range control
1200 Front PTO
1220 Live PTO
1320 Front-wheel drive
1430 Hydrodamp
1432 Hydraulic pump
1470 Transmission lubrication system
1490 Pump drive
1530 ML variable-displacement system
1600 Enhanced actuation system valves
1620 Enhanced actuation system pipes
2000 Engine
2010 Cylinder head
2020 Speed adjustment
2050 Cooling system
2060 Fuel system
2170 Exhaust brake
2180 Cold-start system
2190 Intercooler
2210 Crankcase
2250 Engine preheater
2312 Lubrication
2710 Injection pump
2712 Injectors
2714 Governor

Farmer 400
Fav 700
Fav 900
Tractor / General system
Assembly overview A
General
04/2000 0000 000009
A
b2/4 Capitel Docu-No.
Index
Date Version Page Assembly overview
Text-module
Text-module
Text-module
Text-module
Text-module
Text-module
Text-module
3000 Front axle
3010 Front axle support
3020 Axle housing
3050 Suspension
3060 Suspension valve fitting
3070 Suspension pipe
3100 Track rod
3120 Steering cylinder
3170 Frame
3180 Cardan shaft
3190 Diff. lock actuation system
4000 Steering
4070 Steering wheel
4090 Hydr. steering assembly
5000 Vehicle body
5010 Body
5030 Driver's seat
5050 Hitch
5161 Hitch trailer coupling
5200 Cab mount, suspension
5500 Air conditioning
5520 Compressor drive
5530 Coolant lines
5550 Evaporator
5560 Condenser
5570 Electric cables
8100 Cab
8113 Heater
8114 Ventilation
8117 Windscreen wiper
8121 Cable loom
8600 Power lift
8610 Electrohydraulic control EPC
8618 Electrohydraulic remote control
8631 Power lift
8700 Three-point hitch
8730 Lift arms
8740 Support

Farmer 400
Fav 700
Fav 900
Tractor / General system
Assembly overview A
General
04/2000 0000 000009
A
b3/4 Capitel Docu-No.
Index
Date Version Page Assembly overview
Text-module
Text-module
Text-module
Text-module
Text-module
Text-module
8800 Air compressor
8810 Compressor
8820 Brake fittings
8830 Lines
8850 Electrical actuation system
8890 Air tank
8900 Front loader
8910 Mounting frame
8915 Hydr. implement actuation system
8955 3rd hydr. circuit
8958 Multi-coupling
8970 Pipes
8990 Lift cylinder
9000 Electrics
9010 Generator
9015 Starter inhibitor
9040 Fuses
9050 Battery system
9060 Starter motor system
9200 Front power lift
9210 Power lift
9211 Electrohydraulic remote control
9220 Cylinder
9230 Pipes
9260 Enhanced-control power lift
9280 Frame
9400 Hydr. pump assembly
9410 LS pump
9420 Transmission pump
9430 Steering pump
9500 Hydraulic pipes
9510 Basic circuit
9516 Power lift
9525 with oil cooler
9530 Hydr. trailer brake
9531 Steering
9534 Reversing system

Farmer 400
Fav 700
Fav 900
Tractor / General system
Assembly overview A
General
04/2000 0000 000009
A
b4/4 Capitel Docu-No.
Index
Date Version Page Assembly overview
Text-module
Text-module
Text-module
9600 Hydr. equipment
9605 Hydr. connections
9610 Central control block (ZSB)
9620 Valve fitting
9666 External hydraulic supply
9690 Valve supplement
9700 Electronics
9710 Instrument panel
9715 Vario terminal
9717 LBS - agricultural bus system
9720 Transducer
9730 Radar sensor
9740 E-box
9750 Transmission actuator unit
9760 Joystick
9770 Control unit
9780 Engine EDC
9790 ECU, power lift
9900 Service
9920 Special tools
9970 FENDIAS

Farmer 400
Fav 700
Fav 900 Documentation structure A
General
12.4.2000 0000 000011
A
b1/2 Capitel Docu-No.
Index
Date Version Page Documentation structure
Text-module
The fundamental feature of this documentation is that the different tractor types are divided into main
assemblies which correspond, with a few exceptions for technical reasons, to the FENDOS structure.
These main assemblies are, for example, "0000 - Tractor/General system" ; "1000 - Transmission";
"2000 - Engine" etc.
The main assemblies are sub-divided into subassemblies, e.g. "1005 - Transmission control unit";
"1220 - Live PTO" etc.
Please see document 0000 A 000009 for an overview of the assemblies.
Each assembly is subdivided into various registers which are labelled with a register letter.
These are as follows.
This documentation comprises a large number of self-contained individual documents (=worksheets).
These documents can be used for various applications and are available in different languages.
Each document is given a unique document code (8), which is made up of the chapter no. (1) (=assem-
bly / subassembly), the register letter (2) and the docu-no. (3) and is printed at the right of the footer.
A document can, therefore, be clearly assigned to a main assembly/subassembly and the register.
Explanation of the header and footer:
PM-Picturemodule
Text-module
A - General E - Testing
B - Faults F - Setting and Calibration
C - Documents and Diagrams G - Repair
D - Component Location H - Service - Info
PMTAB_Picture
a Register letter d Validity: chassis no.
b Chapter / section e Other validity notes
c Type validity

Farmer 400
Fav 700
Fav 900 Documentation structure A
General
12.4.2000 0000 000011
A
b2/2 Capitel Docu-No.
Index
Date Version Page Documentation structure
PM-Picturemodule
Text-module
Text-module
All assemblies are paginated sequentially, starting at page 1.
Text-module
The document code does not have to be sequential, i.e. gaps may occur.
The docu-no. is not the page number in the documentation. The page number is listed on the right in
the contents.
PMTAB_Picture
1 Main assembly /
subassembly 5 No. of pages in document
2 Register 6 Revisionstatus
3 Docu-no. 7 Date created
4 Section 8 Document code

Tractor / General system
Notes on documentation A
General
26.03.2001 0000 000021
A
a1/1 Capitel Docu-No.
Index
Date Version Page Notes on documentation
Text-module
Please note
This Workshop Manual gives the trained expert type-related information for the repair of our tractors. It
is assumed that standard tools and general instruments which are part of the usual equipment in a
workshop will be available. Special tools are kept to the absolute minimum and are shown both at the
point where they are used and in a summary at the end of the manual.
If parts have to be replaced, only genuine spare parts may be used! When placing orders for parts
please always quote the chassis number in accordance with the relevant valid spares documentation.
The division of the assemblies in the Workshop Manual mirrors that of FENDOS.
Maintenance documentation and technical specifications must also be taken into account by
workshops. On completion of a repair, the person responsible must carry out a test drive to ensure that
the tractor is in perfect condition and its roadworthiness can be guaranteed.
We reserve the right to make design changes in the interests of technical progress.
Text-module
Notes on register G - Repairs
The disassembly and reassembly instructions shown represent the design status at the time that the
Workshop Manual was written.
Technical refinement of the product and expansions in terms of different models may require different
work procedures which can be carried out without major difficulty by qualified experts.
These disassembly and reassembly instructions are superseded on publication of the next edition.
Text-module
Important notes on safety at work
It is a fundamental principle that those carrying out repairs are responsible for ensuring their own safety
while working.
Compliance with all applicable safety regulations and statutory provisions is a prerequisite for
avoiding personal injury and product damage during maintenance and repair work. Repair staff
must familiarise themselves with such regulations and provisions before starting work.
The proper repair of Fendt products presupposes that the work will be carried out by appropriately
trained expert staff.
The obligation to provide such training lies with the repair workshop.
Text-module
The following are used in this manual to draw attention to safety issues
Text-module
Read the relevant instructions thoroughly before starting any tests or repair work.
Photos, drawings and components do not always represent the original. They are an illustration of the
work procedure required.
Photos, drawings components are not to scale. No conclusions may be drawn regarding size and
weight (even within a single illustration).
This pictogram warns of situations where a lack of care can lead to personal injury or product
damage.

Farmer 400
Fav 700
Fav 900
Working and steering hydraulics / General system
Safety instructions and measures A
General
12/1999 0000 000012
A
a1/1 Capitel Docu-No.
Index
Date Version Page Safety instructions and measures
Central control block
Text-module
Reason:
Bullet-List
●The pressure pipes of the front suspension between the central control block ZSB and the
suspension cylinders,
●the accumulators ASP1 and ASP2 on the central control block and
●the piped accumulator ZSP
are subject to a pressure of 200 bar even with the engine switched off and the suspension
lowered (=locked)!
Action:
The pressure has to be relieved manually before any repair is carried out or anything is released or
opened in this area.
Note:
The "Lock suspension / lower suspension" command has no effect!
Steps:
PM-Picturemodule
PM-Picturemodule
Text-module
Check:
Emptying of accumulator sounds like flowing liquid as oil temperature increases (scarcely audible in
winter).
Note and comparison:
For tractors without a central control block (e.g. Fav 500) it is still necessary to relieve pressure using
the "External power supply" method.
PMTAB_Picture 1. Loosen stopcock item A (stopcock is labelled
AV2infurther documents and circuitdiagrams)on
top of central control block by approx. 1 turn
anti-clockwise.
PMTAB_Picture 2. Loosen stopcock item B (stopcock is labelled
AV1infurther documents and circuitdiagrams)on
bottom of central control block by approx. 1 turn
anti-clockwise.

Fav 900 Tractor / General system
Fuels and lubricants A
General
Fav 900 chassis number 23/3001 and up
12.11.2001 0000 000029
A
a1/2 Capitel Docu-No.
Index
Date Version Page Fuels and lubricants
Text-module
PM-Picturemodule
Text-module
Filling points Filling
quantity Type 4) Frequency of change 2)
approx.
litres
Engine "Max" with filter
change 24 All-year SHPD engine oil 3) to ACEA E3-96 After50,500,1000op.hrs.thenevery 500 op. hrs. though at least once a
yearifsulphurcontentisupto0.5%5)
Transmission and
differential (refill) 65 STOU SAE 10 W-40 or 15 W-40 then every 2 years or every 2000 operating hours.
Power lift shaft lubrication 0.2 Power lift shaft lubrication
(top-up- only) after 50 operating
hours and in event of leaks
Axle drives per side 13 Special hypoid transmission oil Every 500 operating hours
SAE 85 W-90 or SAE 80 W-90 then every 2 years
or SAE 90 as per API GL-5 or every 2000 op. hrs.
Front axle differential 9.5 No STOU or other universal oil Front axle differential and hub drives
Hub drives per side 2.7 After50then1000op.hrs,thenevery
2 years or 2000 op. hrs.
Front PTO 4.2 After 500 op. hrs, then every 2 years
or 2000 op. hrs.
Rearaxlestubshaft(optio-
nal) axle drivers per side 13 Special hypoid transmission oil 85 W-140 to API GL-5 After 500 op. hrs, then every 2 years or 2000 op. hrs.
Hydraulics STOU SAE 10W-30, 10W-40,
15W-30 After 1000 op. hrs.
Quantity for max. filling 70 Also permissible: HD-SAE 20
W-20 to API-CD then every 2 years or every 1000 op. hrs.
Fuel tank 530 Diesel 5) Fill up after use
Cooling system 26 Water with 35 - 50% vol/vol anti-
freeze and anti-corrosion agent Change antifreeze every 2 years
Brake and clutch system 0.8 Pentosin CHF 11S Every 2 years
(X 902.011.622)
Air compressor 0.5 Ethyl alcohol antifreeze Fill up only below + 5°C
(X 902.015.003)
Lubrication points Lithium-saponified grease,
NLGI class 2 See Lubrication Chart
see Lubrication Chart (worked penetration coefficient
265-295) -regularly oil all other joints and bearing surfaces
3) VISCOSITY OF OILS IN ENGINE
Monograde oils Multigrade oils
PMTAB_Picture 1) Asindicatedondipstick, by overflow from filling
point etc.
2) Whichever is the sooner.
4) For permitted tradenames, if specified, see
current fuels and lubricants list which all Fendt
dealers receive as a service circular.
5) If diesel fuel contains more than 0.5 - 1%
sulphur, oil-change intervals must be halved. A
sulphur content of less than 0.05% is
recommended, though the fuel supplier must
confirm that an adequate lubricant effect is
guaranteed(e.g. by meansof additives). Only use
alternative fuels, e.g. RME, once discussed with
the Service Workshop .

Fav 900 Tractor / General system
Fuels and lubricants A
General
Fav 900 chassis number 23/3001 and up
12.11.2001 0000 000029
A
a2/2 Capitel Docu-No.
Index
Date Version Page Fuels and lubricants
Text-module
1) = Lithium-saponified, dripping point approx. 185°C, worked penetration coefficient 265 to 295
(soft)
2) = Alvania 2 or Renolit MP
3) = Components which are to be bonded must be free of paint, oil and grease. Apply synthetic
bonding agent to the dry joint surfaces of both components; after mating them, leave them for
the specified curing time without exposing them to the air.
Lubricants, sealants and bonding agents
High-pressure grease for long-term lubrication, e.g. for
splined shaft profiles X 902.002.472 long-life grease
Grease for lubricating sealing lips of shaft seals Multi-purpose grease 1) and 2)
Sealant (fully curing) for shaft seals with steel cage Serdon X 903.051.711
Shaft seals with rubberised outer ring
Coat outer rings with Spirit/water mixture 1:1
Sealant (not fully curing) for surfaces of gearbox housing Loctite X 903.050.074
Sealant e.g. for Hall-effect sensors with rotational direction
sensor (non-curing) F 119.200.210.930
Synthetic bonding agent Normal Loctite bolt-sealant
X 903.050.084 3)
Synthetic bonding agent Loctite high-strength X 903.050.091 3)
High-speed cleaner for use against grease and oil, 520 ml
spray can X 907.505.000

Farmer 400
Fav 700
Fav 900
Tractor / General system
Tightening torques for screws/bolts in Nm (kpm) A
General
03/2000 0000 000007
A
a1/1 Capitel Docu-No.
Index
Date Version Page Tightening torques for screws/bolts in Nm (kpm)
Text-module
Coefficient of friction: µtot. 0.14 for nuts and bolts without aftertreatment and for phosphated nuts.
Tighten by hand.
Tightening torques, unless otherwise specified, can be taken from the following table.
PM-Picturemodule
PMTAB_Picture

Farmer 400
Fav 700
Fav 900
Tractor / General system
Tractor diagnostics with terminal A008 A
General
Fav 900 chassis number 23/3001 and up
12.2.2001 0000 000015
A
a1/2 Capitel Docu-No.
Index
Date Version Page Tractor diagnostics with terminal A008
PM-Picturemodule
PM-Picturemodule
PM-Picturemodule
PMTAB_Picture Ignition ON
Press F5 to switch to second main menu level.
PMTAB_Picture Second main menu level is displayed.
Press F4 to open Screen Brightness menu.
PMTAB_Picture Screen Brightness menu is displayed.
Press F1 to open Diagnostics menu.

Farmer 400
Fav 700
Fav 900
Tractor / General system
Tractor diagnostics with terminal A008 A
General
Fav 900 chassis number 23/3001 and up
12.2.2001 0000 000015
A
a2/2 Capitel Docu-No.
Index
Date Version Page Tractor diagnostics with terminal A008
PM-Picturemodule
PM-Picturemodule
Text-module
Note:
The Diagnostics terminal is not a replacement for measuring pressure in the transmission
circuit or electrical readings.
The Diagnostics terminal provides a reference value for the Vario transmission functions.
Possible applications:
Bullet-List
●Loss of power in tractor (question: transmission or engine? )
●Transmission is overheating (question: how high is the transmission discharge temperature for
various tasks? )
●Checking setpoint engine speed
PMTAB_Picture Diagnostics menu is displayed.
●High pressure - Transm ission - Sens or B008
indicates oil pressure in transmission
high-pressure circuit. ( bar )
●Setpoint speed accelerator potentiometer
B018 indicates setpoint engine speed. (rpm)
●Temp erature sensor discharge
B009 indicates discharge temperature of
transmission high-pressure circuit.
(digit = digital units)
●Trans mission - Act ion - Prio rity - F unct ion
indicates transmission's control status.
(actuated, automatic maximum output control,
cruise control, control via joystick, no control
action)
●Press ESC to return to Screen Brightness
menu.
PMTAB_Picture Press F5 to open Diagnostics Help menu.
This menu displays the conversion factors for the
digital units (digit).
Press ESC to return to Diagnostics menu.

Fav 900 Tractor / General system
Technical specifications A
General
Fav 900 chassis number 23/3001 and up
2.8.2001 0000 000028
A
a1/4 Capitel Docu-No.
Index
Date Version Page Technical specifications
Text-module
Model 916 920
Engine
Type of engine DO836LE504 DO836LE503
Turbocharger / intercooler with / with with / with
No. of cylinders / cooling 6 / water 6 / water
Bore / stroke mm 108 / 125 108 / 125
Effective displacement l 6870 6870
Idling speed rpm 780 +/-30 780 +/-30
Rated speed rpm 2150 2150
No-load engine speed rpm 2260-2320 2280-2340
Fuel l 530 530
Engine stop electrical electrical
Noise level at driver's ear dB(A) 72 72
Angle of engine
Tractor stability must be guaranteed
Lengthways in travel direction front / rear degree 25 25
Across travel direction left / right degree 25 25
Weights and dimensions
with following tyres and track width
Tyres front 480/70R34 480/70R34
Tyres rear 580/70R42 580/70R42
Track width front mm 2000 2000
Track width rear mm 1970 1970
Overall length mm 4940 4940
Overall width mm 2550 2550
Overall height incl. cab mm 3095 3095
Ground clearance mm 605 605
Wheelbase mm 2840 2840
Flange centre distance front mm 1892 1892
Flange centre distance rear mm 1890 1890
Min. turning circle radius without / with steering brake mm 5.9/54 5.9/5.4
Kerb weight kg 8750 8750
Max. permissible gross vehicle weight at 50km/h kg 12000 12000
Max. permissible gross vehicle weight with mounted
implements, depending on tyres kg 14000 14000
Max. permissible axle load kg 6500 6500
Max. permissible axle load rear kg 7730 7730
Maximal vertical load on trailer coupling kg 2000 2000
Maximal vertical load on trailer hitch kg 3000 3000
PTO 540/750/1000
PTO profile 1 3/4" 6-spline 1 3/4" 6-spline
PTO speed at rated engine speed and 540 setting rpm 569 569
PTO speed at rated engine speed and 750 setting rpm 726 726
PTO speed at rated engine speed and 1000 setting rpm 1058 1058
Max. permissible torque at 540 setting Nm 3500 3500
Max. permissible torque at 750 setting Nm 2100 2100
Max. permissible torque at 1000 setting Nm 1600 1600
Front PTO 1000
PTO speed at rated engine speed and 1000 setting rpm 1111 1111
Max. permissible torque for 1000 Nm 830 830

Fav 900 Tractor / General system
Technical specifications A
General
Fav 900 chassis number 23/3001 and up
2.8.2001 0000 000028
A
a2/4 Capitel Docu-No.
Index
Date Version Page Technical specifications
Text-module
Note:
The warranty becomes null and void if changes are made to the power output governor and
max. speed setting or if the permissible loads and weights are exceeded.
Note:
With PTO operation:
If the maximum permissible torque can be exceeded because of the particular application,
use cardan shafts with a safety coupling and freewheel, if appropriate.
Maximum protection against seizing at peak torques 4000 Nm.
Hydraulics
Working pressure bar 200 200
Hydraulic pump l 112 112
Available hydr. oil at max. capacity l 50 50
Rear power lift
Three-point Cat. 2/3 Cat. 2/3
Control EPC EPC
Max. lift capacity kN 90 90
Front power lift (optional)
Three-point Cat. 2 Cat.2
Max. lift capacity kN 50 50
Implement weight up to approx. kg 3600 3600
Transmission
Vario continuously variable transmission km/h 50 50
Range I forwards km/h 0.02 - 32 0.02 - 32
Range I reverse km/h 0.02 - 20 0.02 - 20
Range II forwards km/h 0.02 - 50 0.02 - 50
Range II reverse km/h 0.02 - 38 0.02 - 38
Electrics
Operating voltage V 12 12
Battery V/Ah 12/2 x 90 12/2 x 90
Alternator W/V/A 2520/14/2x90 2520/14/2x90
Starter kW 4.0 4.0
Wheel tightening torques
(threads and locating faces lightly oiled)
Front wheels Nm 450 450
Rear wheels Nm 620 620
Model 916 920

Fav 900 Tractor / General system
Technical specifications A
General
Fav 900 chassis number 23/3001 and up
2.8.2001 0000 000028
A
a3/4 Capitel Docu-No.
Index
Date Version Page Technical specifications
Text-module
Model 924 926
Engine
Type of engine DO836LE502 DO836LE501
Turbocharger / intercooler with / with with / with
No. of cylinders / cooling 6 / water 6 / water
Bore / stroke mm 108 / 125 108 / 125
Effective displacement l 6870 6870
Idling speed rpm 780 +/-30 780 +/-30
Rated speed rpm 2250 2250
No-load engine speed rpm 2400-2460 2420-2480
Fuel l 530 530
Engine stop electrical electrical
Noise level at driver's ear dB(A) 72 72
Angle of engine
Tractor stability must be guaranteed
Lengthways in travel direction front / rear degree 25 25
Across travel direction left / right degree 25 25
Weights and dimensions
with following tyres and track width
Tyres front 540/65R34 600/65R34
Tyres rear 650/65R42 650/85R38
Track width front mm 2000 2000
Track width rear mm 1970 1970
Overall length mm 4940 4940
Overall width mm 2580 2640
Overall height incl. cab mm 3110 3110
Ground clearance mm 605 605
Wheelbase mm 2840 2840
Flange centre distance front mm 1892 1892
Flange centre distance rear mm 1890 1890
Min. turning circle radius without / with steering brake mm 5.9/5.4 5.9/5.4
Kerb weight kg 8800 8800
Max. permissible gross vehicle weight at 50km/h kg 12000 12000
Max. permissible gross vehicle weight with mounted
implements, depending on tyres kg 14000 14000
Max. permissible axle load front kg 6500 6500
Max. permissible axle load rear kg 7730 7730
Maximal vertical load on trailer coupling kg 2000 2000
Maximal vertical load on trailer hitch kg 3000 3000
PTO 540/750/1000
PTO profile 1 3/4" 6-spline 1 3/4" 6-spline
PTO speed at rated engine speed and 540 setting rpm 596 596
PTO speed at rated engine speed and 750 setting rpm 760 760
PTO speed at rated engine speed and 1000 setting rpm 1108 1108
Max. permissible torque at 540 setting Nm 3500 3500
Max. permissible torque at 750 setting Nm 2100 2100
Max. permissible torque at 1000 setting Nm 1600 1600
Front PTO 1000
PTO speed at nominal speed, 1000 version rpm 1062 1062
Max. permissible torque at 1000 setting Nm 830 830

Fav 900 Tractor / General system
Technical specifications A
General
Fav 900 chassis number 23/3001 and up
2.8.2001 0000 000028
A
a4/4 Capitel Docu-No.
Index
Date Version Page Technical specifications
Text-module
Note:
The warranty becomes null and void if changes are made to the power output governor and
max. speed setting or if the permissible loads and weights are exceeded.
Note:
With PTO operation:
If the maximum permissible torque can be exceeded because of the particular application,
use cardan shafts with a safety coupling and freewheel, if appropriate.
Maximum protection against seizing at peak torques 4000 Nm.
Hydraulics
Working pressure bar 200 200
Hydraulic pump l 117 117
Available hydr. oil at max. capacity l 50 50
Rear power lift
Three-point Cat. 2/3 Cat. 2/3
Control EPC EPC
Max. lift capacity kN 99.8 99.8
Front power lift (optional)
Three-point Cat. 2 Cat.2
Max. lift capacity kN 50 50
Implement weight up to approx. kg 3600 3600
Transmission
Vario continuously variable transmission km/h 50 50
Range I forwards km/h 0.02 - 32 0.02 - 32
Range I reverse km/h 0.02 - 20 0.02 - 20
Range II forwards km/h 0.02 - 50 0.02 - 50
Range II reverse km/h 0.02 - 38 0.02 - 38
Electrics
Operating voltage V 12 12
Battery V/Ah 12/2 x 90 12/2 x 90
Alternator W/V/A 2520/14/2x90 2520/14/2x90
Starter kW 4.0 4.0
Wheel tightening torques
(threads and locating faces lightly oiled)
Front wheels Nm 450 450
Rear wheels Nm 620 620
Model 924 926

Farmer 400 Fav 700 Fav 900
Tractor / General system
Vario Tractors - Failure Codes B
Faults
12/1999 0000 000001
B
b1/47 Capitel Docu-No.
Index
Date Version Page Vario Tractors - Failure Codes
FCT_InitPage
Fault
code Id code Brief description Description Consequences Link FENDIAS / Note
0.0.11 A021;
A022 ECU, EDC; ECU, EMR EDC / EMR bus fault. Fault in ECU Tractor can be driven using accelerator.
Programming errors in
ECU. Fault message, no restrictions. EOL reprogramming necessary.
0.0.12 A008 Terminal Bus Failure no functions available,
no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F039, F046
0.0.13 A004 Control console Bus Failure no functions available,
no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.14 A001;
A002 Transmission control module Bus Failure no functions available, no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.15 A001,
A002 AWD; Differential - Lock acivation Bus Failure no functions available, no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.16 A001,
A002 Rear PTO Bus Failure no functions available, no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.17 A001,
A002 Front PTO Bus Failure no functions available, no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.18 A005 EPC Rear Bus Failure no functions available,
no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.19 A005 Front - Powerlift Bus Failure no functions available,
no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.0.1A A005 Spool valves Bus Failure no functions available,
no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041

Farmer 400 Fav 700 Fav 900
Tractor / General system
Vario Tractors - Failure Codes B
Faults
12/1999 0000 000001
B
b2/47 Capitel Docu-No.Index
Date Version Page Vario Tractors - Failure Codes
0.0.20 A005 CAN-Bus-wiring Bus Failure no functions available,
no display VoltagesupplyCAN-Bus on fuse board A013;
fuses F040, F041
0.1.50 A007 Instrument panel VDO instrument panel
EEPROM not
programmed
Malfunctions in
instrument panel EOL reprogramming necessary
0.1.51 B012 Engine oil pressure
sensor Sensor failure, wiring failure no monitoring ! Electrical diagram "Dashpanel"
0.1.54 B019 Pressure sensor
compressed air tank Sensor failure, wiring failure no display Electrical diagram "Dashpanel"
0.1.55 S036 Level Sensor hydraulic
oil Sensor failure, wiring failure no monitoring ! Electric diagram "Spool valves 1"
0.1.56 B005 Engine temperature
sensor Sensor failure, wiring failure no monitoring ! Electrical diagram "Dashpanel"
0.1.57 B006 Sensor, intercooler
temperature Sensor fault, wiring fault No monitoring ! Circuit diagram: "Instrument panel"
(F400, F700); "EDC
control module" (F900)
0.1.59 B007 Fuel level sensor Sensor failure, wiring
failure no monitoring ! Electrical diagram "Dashpanel"
1.1.01,
evtl.
4.2.81
B038 Position sensor
accelarator pedal EDC
( yellow marker )
Signal out of range Chapter 2000 Reg.B
(EDC-Failure) Electric diagram "EDC Control "
1.1.03 B029/-
B038 Position sensor accelarator pedal EST
( Elektronic box comfort,
red marker ) / Position
sensoraccelaratorpedal
EDC ( yellow marker )
values not
corresponding B029 /
B038
Restricted Operating
Possibilities,
Chapter 2000 Reg.B
(EDC-Failure)
Electric diagram
"EDC Control "
1.1.7E B035 Position sensor manual
accelarator Signal out of range. Restricted Operating Possibilities,
Chapter 2000 Reg.B
(EDC-Failures)
Electric diagram
"EDC Control "
Fault
code Id code Brief description Description Consequences Link FENDIAS / Note