Fisher & Paykel PROFESSIONAL Series User manual

RDV2 & RGV2
models
PROFESSIONAL RANGE
INSTALLATION GUIDE
US CA
591090E 07.18

4
2MODEL IDENTIFICATION
RGV2-366
RDV2-366
RGV2-305
RDV2-305
RGV2-304
RDV2-304
RGV2-364GD
RDV2-364GD
RGV2-488
RDV2-488 RGV2-486GL
RDV2-486GL
RGV2-486GD
RDV2-486GD
RGV2-485GD
RDV2-485GD
48” MODELS
36” MODELS 30” MODELS

6
5PRODUCT DIMENSIONS – 30” MODELS
B
C
C
F
H
ID
J
E
G
A
PRODUCT DIMENSIONS 30” MODELS
inches (mm)
AOverall height of range (from floor to cooktop, excluding
pan supports and vent trim)
min 35 3/4’’ (908)
max 36 3/4’’ (933)
BOverall width of range 29 7/8” (759)
COverall depth of range (excluding handle and dials) 29 1/8” (740)
DDepth from rear of chassis to cabinetry face – projecting control panel 25 1/8” (638)
EDepth from rear of chassis to cabinetry face – flush control panel 27 11/16” (703)
FHeight from top of countertop to top of pan supports 1 9/16” (40)
GHeight from top of countertop to top of
- vent trim (if fitted)
- angled vent trim (if fitted)
1 3/4” (45)
3 1/2” (90)
HHeight from top of countertop to bottom of chassis 35 1/4” (895)
IAdjustable feet height min 1/2’’ (13)
max 1 1/2’’ (38)
JDepth of open door to front control panel 19 1/8” (486)
PLAN
PROFILE
FRONT
RGV2-305 shown for Illustration purposes only

7
5PRODUCT DIMENSIONS – 36” MODELS
B
C
H
I
C
F
D
J
E
G
A
PRODUCT DIMENSIONS 36” MODELS
inches (mm)
AOverall height of range (from floor to cooktop, excluding
pan supports and vent trim)
min 35 3/4’’ (908)
max 36 3/4’’ (933)
BOverall width of range 35 7/8” (911)
COverall depth of range (excluding handle and dials) 29 1/8” (740)
DDepth from rear of chassis to cabinetry face – projecting control panel 25 1/8” (638)
EDepth from rear of chassis to cabinetry face – flush control panel 27 11/16” (703)
FHeight from top of countertop to top of pan supports 1 9/16” (40)
GHeight from top of countertop to top of
- vent trim (if fitted)
- angled vent trim (if fitted)
1 3/4” (45)
3 1/2” (90)
HHeight from top of countertop to bottom of chassis 35 1/4” (895)
IAdjustable feet height min 1/2’’ (13)
max 1 1/2’’ (38)
JDepth of open door to front control panel 19 1/8” (486)
PLAN
PROFILE
FRONT
RGV2-364GD shown for Illustration purposes only

8
5PRODUCT DIMENSIONS – 48” MODELS
B
C
H
I
C
F
D
J
E
G
A
PRODUCT DIMENSIONS 48” MODELS
inches (mm)
AOverall height of range
(from floor to cooktop, excluding pan supports and vent trim)
min 35 3/4’’ (908)
max 36 3/4’’ (933)
BOverall width of range 47 7/8” (1216)
COverall depth of range (excluding handle and dials) 29 1/8” (740)
DDepth from rear of chassis to cabinetry face – projecting control panel 25 1/8” (638)
EDepth from rear of chassis to cabinetry face – flush control panel 27 11/16” (703)
FHeight from top of countertop to top of pan supports 1 9/16” (40)
GHeight from top of countertop to top of
- vent trim (if fitted)
- angled vent trim (if fitted)
1 3/4” (45)
3 1/2” (90)
HHeight from top of countertop to bottom of chassis 35 1/4” (895)
IAdjustable feet height min 1/2’’ (13)
max 1 1/2’’ (38)
JDepth of open door to front control panel 19 1/8” (486)
PLAN
PROFILE
FRONT
RGV2-486GD shown for Illustration purposes only

11
7INSTALLATION SCENARIOS AND USE OF BACKGUARDS
Important notes
● All ranges come fitted standard with with an Integral Flat Vent Trim
● There are three different backguards available for purchase:
● Range Mount Low Backguard
● Wall Mount High Backguard with Low Shelf
● Wall Mount High Backguard with High Shelf, also supplied with an Angled Vent Trim.
● For installations against non-combustible* surfaces only, you may install the range without a backguard or choose any of the three backguards.
● For installations close to combustible surfaces (above the cooking surface), without a backguard, there must be a minimum 6” (152mm) clearance
(see Scenario 2 or 7 opposite)
● For installations immediately against combustible surfaces (above the cooking surface), you must purchase and fit the Wall Mount High Backguard
High Shelf and Angled Vent Trim (see Scenario 5 opposite)
● The cooking surface must sit flush or above the adjacent countertop level.
Note: For more information on Backguard installation, refer to the separate instructions provided with your backguard.
Backguard Installation Instructions can also be downloaded from our website, www.fisherpaykel.com
* Non-combustible surfaces:
as defined in ‘National Fuel Gas Code’ (ANSI Z223.1, Current Edition). Clearances from non-combustible materials
are not part of the ANSI Z21.1 scope and are not certified by UL. Clearances of less than 6” (152mm) must be
approved by the local codes and/or by the local authority having jurisdiction.
BACKGUARD MODEL NUMBERS
RANGE
RANGE
MOUNT LOW
BACKGUARD
WALL
MOUNT HIGH
BACKGUARD
LOW SHELF
WALL
MOUNT HIGH
BACKGUARD
HIGH SHELF
BACKGUARD
WIDTH
30” models BGRV2-1230 BGRV2-3030 BGRV2-3030H 29 7/8” (759mm)
36” models BGRV2-1236 BGRV2-3036 BGRV2-3036H 35 7/8” (911mm)
48” models BGRV2-1248 BGRV2-3048 BGRV2-3048H 47 7/8” (1216mm)

18
!5 GAS CONNECTION
Gas requirements
Verify the type of gas supplied to the location. The range is shipped from the factory set up and adjusted for Natural Gas or LP, depending on the specific model ordered.
Verify that the range is compatible with gas supply at the installation site before proceeding further. Return the range to the dealer if the unit is not set for the gas supplied at the site.
NATURAL GAS
● Connection: 1/2” NPT Minimum 5/8” dia. flex line. Supply Pressure: 6” to 9” W.C.
LP Gas
● Connection: 1/2” NPT Minimum 5/8” dia. flex line. Supply Pressure: 11” to 14” W.C.
● A regulator is required at the LP source to provide a maximum pressure of 14” W.C. to the range regulator.
Requirements for hook-up to gas supply
● The gas supply connections should be made by a qualified technician in accordance with local codes or ordinances. In the absence of a local code, the installation must conform to the latest
edition of National Fuel Gas Code ANSI Z.223.1 (Warning: this appliance must be installed by a licensed plumber or gas fitter when within the Commonwealth of Massachusetts).
● A manual shut-off valve (supplied by the installer) must be installed in an accessible location in the gas line external to the appliance for the purpose of turning on or shutting off gas to
the appliance. (In Massachusetts such shut-off valves should be approved by the Board of State Examiners of Plumbers & Gas Fitters.) The shut-off valve must be located within 6 feet
(1.8 meters) of the appliance it serves.
IMPORTANT!
Fisher & Paykel recommends installing the manual shutoff valve in a location readily accessible by the customer, so that gas to the
appliance can be shut off in an emergency situation. However, the appliance must not be modified in any way to accommodate such placement.
● The gas supply line must not protrude beyond the back of the appliance.
● Make sure the gas supply is turned off at the wall valve before connecting the appliance
● Leak-testing of the appliance shall be conducted according to the manufacturer’s instructions. See instructions following.
● The appliance must be isolated from the building’s gas supply piping system by closing its individual manual shut-off valve during any pressure
testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5kPa.). The appliance and its individual shut-off valve must
be disconnected from the gas supply piping system during any pressure testing of the system at the test pressures in excess of 1/2 psig (3.5kPa.).
When checking the manifold gas pressure, the inlet pressure to the regulator should be at least 7.0” W.C. for natural gas or 12.0” for LP.
● The flex line for the gas supply must be metal and be approved for appliance use by a certifying agency (CSA, CGA, or UL).
Never use a hose made of rubber or other synthetic material, as the heat may cause the hose to melt and develop leaks.
● When hooking up the gas supply from the wall hard pipe to the range hard pipe, installation length of flex line between range/wall hard piping must accommodate range being pulled from wall
for cleaning or servicing purposes. When range is pulled from wall, no strain should occur at range or wall hard pipe connections.
Installer supplied manual
shut-off valve “open” position
Gas supply line
To Range