Fisher & Paykel OR90SDBSIPX1 User manual

Installation instructions
Please follow the installation steps below to ensure your appliance operates correctly.
Dimensions and clearances
• The cooker must be installed no less than 50 mm away from any side walls which exceed the height of the
cooktop.
• The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand
temperatures of 65 °C above room temperature.
• Do not install the cooker near flammable materials (eg curtains).
• If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
1

Locating the area for electrical connection
Fig. 1 Area for electrical connection
Fig. 2 Dimensions and distances from cooker
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
2

Fig. 3a Screw/unscrew the feet to get the required
height
Leveling the cooker
Using the supplied
adjustable feet is
MANDATORY. For safety
reasons and to ensure
adequate ventilation, the
cooker chassis MUST NOT
sit directly on the floor, a
plinth, or other support
surface.
• For ease of installation, first remove the kickstrip. To
remove the kickstrip, unscrew the two screws
holding it in place.
• The cooker is already fitted with four levelling feet.
• Level the cooker by screwing or unscrewing the
feet.
• Make sure you follow the instructions in Figs. 3a,
3b, and 3c.
• Note: nuts are supplied with the cooker in a
separate kit.
Do not refit the kickstrip until you have installed the
anti-tip bracket.
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
3

Fig. 3b Do not use the supplied nuts for height
adjustments between 0 and 8mm
Fig. 3c Use the supplied nuts for height adjustments
between 8 and 13mm
Fitting the anti-tilt bracket
To restrain the appliance
and prevent it tipping
accidentally, the anti-
tilt bracket and restraining
plate supplied must be
fitted according to the
instructions below.
1. Drill four 8mm diameter holes for the fixing screws
(two in the wall and two in the floor-see Fig.4) and
insert the plastic plugs supplied. bracket
Before drilling the holes,
check that you will not
damage any pipes or
electrical wires.
2. Attach the anti-tilt bracket to the floor and rear wall
using the four screws supplied, as shown in Fig. 4.
3. After attaching the anti-tilt bracket securely, slide
the cooker into place. Ensure that the left rear foot
slides under the bracket, as shown in Fig.4.
4. Access the bracket by removing the drawer (Fig.
5).
a. Slide out the drawer completely.
b. Press the lever of the left guide rail down and
pull the lever of the right guide rail up.
Fig. 4 Attaching the anti-tilt bracket and sliding the
cooker into place
Fig. 5 Accessing the anti-tilt bracket by removing the
drawer
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
4

c. Holding the levers, disengage and remove
the drawer.
5. If fitted, remove the kickstrip (see ‘Leveling the
cooker’). Fix the restraining plate by sliding it into
place and securing it with the fixing screw and
washer supplied. See Fig. 6.
6. Replace the drawer (Fig. 7):
a. Insert the drawer rails into the guide rails.
b. Gently push the drawer in completely; the
safety catches will automatically hook.
7. Replace the kickstrip using the two screws.
Beware of sharp
edges when removing
or replacing the
drawer.
Fig. 6 Fixing the restraining plate
Fig. 7 Replacing the drawer
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
5

Moving the Cooker
To prevent damaging the
adjustable feet or lower
trim, ensure the cooker is
always lifted by two people.
Do not lift the cooker by the
door handles.
DO NOT DRAG the cooker.
Lift the feet clear of the
floor.
Take extra care not to
damage the door sensor
(top left of oven).
Fig. 8 Correctly lifting the cooker
Fig. 9 Incorrectly lifting the cooker Fig. 10 Incorrectly moving the cooker
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
6

Fixing the backguard
Before installing the cooker, assemble the backguard “C”
.
• The backguard “C” can be found packed at the rear
of the cooker.
1. Before assembling, remove any protective film/
adhesive tape.
2. Remove the two spacers “A” and the screw “B”
from the rear of the cooktop.
3. Assemble the backguard as shown and fix it by
screwing the central screw “B” and the spacers “A”.
Fig. 11 Assembling the backguard
Connecting the power supply cable
This cooker must be connected to the electricity supply only by an authorised person.
To connect the power supply cable to the cooker, it is necessary to:
1. Unhook the terminal board cover by inserting a screwdriver into the two hooks ‘A’ (fig. 12).
2. Unscrew the screw ‘D’ and open completely the cable clamp ‘E’ (figs. 14).
3. Position the U bolts ‘F’ onto terminal board ‘G’ (figs. 14) according to the diagrams in fig. 13.
4. Connect the phase, neutral and earth wires to terminal board ‘G’ according to the diagrams in figs. 13 - 14.
5. Strain the feeder cable and block it with cable clamp ‘E’ (by screwing screw ‘D’).
6. Close the terminal block cover (check the two hooks ‘A’ are correctly hooked).
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
7

To connect the power supply cable DO NOT unscrew the screws fixing the cover plate
behind the terminal block.
WARNING: If the power supply cable is damaged, it must be replaced only by an
authorised service agent in order to avoid a hazard.
Voltage and power consumption
220-240/380-415 V 3N~ 50 Hz 47.2A (230V) 10850 W (diversity not applied)
Fig. 12 Terminal block
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
8

Fig. 13 Connection diagrams
Feeder cable section
In Australia and New Zealand: this cooker must be connected to electrical supply using V105 insulated cable.
220-240 V~ 3 x 6 mm2 (*)
380-415 V 3N~ 5 x 2,5 mm2 (*)
380-415 V 2N~ 4 x 6 mm2 (*)
* Connection with wall box connection.
• Diversity factor applied.
• A diversity factor may be applied to the total loading of the appliance only by a suitably qualified person.
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
9

ELECTRIC DIAGRAM KEY
F1 Oven switch
ST Safety thermostat
STL Safety thermal overload
TL Thermal overload
TL1 Induction hob thermal overload
PR Electronic programmer
PB Temperature probe
TS Oven temperature selector
EC Oven function selector (encoder)
SF State functions
DL Door lock device
R2 Relay 2
R3 Relay 3
LF Oven lamp
TR Oven lamps transformer
S1 Door lock indicator lamp
S2 Line pilot lamp
COven top heating element
GOven grill heating element
SI Oven bottom heating element (int.)
SE Oven bottom heating element (ext.)
CI Oven circular heating element
UD Induction units user display
PCB Induction units PCB
RSI Rotary selector interface
DLM Door lock motor
GIR Rotisserie motor
VOven fan motor
CF Cooling fan motor
RS Resistance (220 Ohm)
RProduct relay
MTerminal block
TEarth Connection
https://producthelp.fisherpaykel.com/nz/Cook/Freestanding_Cookers/Induction/OR90SDBSIPX1/User_Guide_OR90SDBSIPX1/02_Installation_instructions
Updated: Wed, 27 Mar 2019 03:09:12 GMT
Powered by
10