Fisher & Paykel OR30SDPWSX1 User manual

Installation Instructions
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.
Improper installation, adjustment, alteration, services, or maintenance can cause injury or
property damage. Consult a qualified installer, service agent, or the gas supplier.
The use of suitable protective clothing/gloves is recommended when handling or installing
this appliance.
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
1

Tools Needed for Installation (not supplied with the appliance)
Screwdriver 2 - Wrench Pencil Tape Measure
Suitable Protective Gloves Hammer Adjustable wrench Adjustable pliers Drill
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
2

Dimensions and Clearances
• The cooker must be installed no less than 2” (50 mm) away from any side walls which exceed the height of the
cooktop.
• The cabinetry surrounding the cooker must be made of heat-resistant material and must be able to withstand
temperatures of 150 °F (65 °C) above room temperature.
• Do not install the cooker near flammable materials (eg curtains).
• If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.
Locating the Area for Electrical Connection
Grounded Outlet
should be located from the left to the right side of the range; from 5” 7/16 (138 mm) to 6” 1/8 (155.5 mm) [depending on
feet regulation] from the floor.
The electric cord with 4-prong ground plug (NEMA 14-50P) shall have a minimum length of 48” (1220 mm) beyond the
back of the appliance.
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
3

The range CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical
surfaces above 36” (914 mm) high.
There must be a minimum of 2” (50 mm) side clearance from the range to such combustible surfaces TO THE RIGHT
above the 36” (914 mm) high countertop; or there must be a minimum of 2” (50 mm) side clearance from the range to
such combustible surfaces TO THE LEFT above the 36” (914 mm) high countertop.
One side (left or right) above the 36” (914 mm) high countertop must always be kept clear.
The maximum upper cabinet depth recommended is 13” (330 mm).
Any wall cabinet above the range must be a minimum of 30” (762 mm) above the countertop with a minimum width of
30” (762 mm) and must be centered with the range. Side wall cabinets above the range must be a minimum of 18” (457
mm) above the countertop.
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
4

Moving the Cooker
To prevent damaging the adjustable feet or lower trim, ensure the cooker is always lifted by
two people.
Do not lift the cooker by the door handles.
DO NOT DRAG the cooker. Lift the feet clear of the floor.
Take extra care not to damage the door sensor (top right of oven).
Correctly Lifting the Cooker
Incorrectly Lifting the Cooker Incorrectly Moving the Cooker
Fixing the Backguard
It is Mandatory to Install the Backguard.
Before installing the cooker, assemble the backguard “C” .
The backguard “C” can be found packed with the cooker.
1. Before assembling, remove any protective film/adhesive tape.
2. Assemble the backguard “C” as shown.
3. Screw in the two screws “A”, interposing the spacers.
4. Screw in the central screw “B.
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
5

Assembling the backguard
Leveling the Range
The range is equipped with 4 LEVELING FEET and may be leveled by screwing or unscrewing the feet. Follow the
directions below
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
6

Assembling the Backguard
Anti-Tip Stability Device Installation Instructions
1. The anti-tip bracket has to be attached as shown on figure below (only rear left side), it has to be fixed on the
floor OR on the rear wall by no. 4 (four) suitable screws (not supplied). Alternatively the anti-tip bracket can
also be fixed on the floor AND on the rear wall by no. 8 (eight) suitable screws (not supplied).
2. After fixing the anti-tip bracket, slide range into place. Be sure the rear left foot slides under the anti-tip bracket
attached.
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
7

You MUST use the Stability Anti-tip bracket to prevent unit from tipping.
Connecting the Power Supply Cable
This cooker must be connected to the electricity supply only by an authorized person.
Your cooker is supplied with a certified 4 prong NEMA 14-50P power cord and should be plugged directly into a properly
grounded socket. Do not under any circumstances cut or remove the forth (ground) prong from the power plug. Do not
ground to a gas pipe.
Do not have a fuse in the neutral or ground circuit.
Do not use an extension cord.
Check with a qualified electrical installer if you are not sure if the range is properly grounded.
If codes permit, and a separate ground wire is used, it is recommended that a qualified electrical technician determines
the ground path and wire gauge are in accordance with local codes.
Be sure that the electrical connection and wire size are adequate and in conformance with: ANSI/NFPA 70 latest
addition and local codes and ordinances;
CSA standard C22.1, Canadian Electrical Code, Part 1 - latest edition and local codes and ordinances.
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
8

When a 4-wire, two phase 120/240V or 120/208V 60Hz AC only electrical supply is available a 50 amp maximum circuit
protection is required, fused on both sides of the line
Replacing the Power Cord
Replacements should only be made by qualified electrical technicians.
If replacing the power cord, use only a suitable UL or CSA approved one. Tighten the power cord using the power cord
strain relief bracket supplied with the appliance. Allow enough slack to easily attach the cord terminals to the terminal
block.
Voltage and Power Consumption
AC 120/240 V 60 Hz 10350 W MAX 43.51 A MAX
AC 120/208 V 60 Hz 7800 W MAX 37.82 A MAX
Location of Nameplate
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
9

Wiring Diagram
Electric Diagram Key
SZ SINGLE COOKING ZONE
DZ DOUBLE COOKING ZONE
ER-SZ ENERGY REGULATOR (SINGLE ZONE)
ER-DZ ENERGY REGULATOR (DOUBLE ZONE)
CZ-PIL COOKING ZONES POWER INDICATOR LAMP
CZ-RHI COOKING ZONES RESIDUAL HEAT INDICATOR LAMPS
OL OVEN LAMP
E61 RELAY
CE CIRCULAR ELEMENT
GE BROIL ELEMENT
TE TOP ELEMENT
BE-INT BOTTOM ELEMENT INT.
BE-EXT BOTTOM ELEMENT EXT.
TPL THERMOSTAT PILOT LAMP
DSPL DOOR SAFETY PILOT LAMP
CF COOLING FAN
OF OVEN FAN
ER ENERGY REGULATOR
Connections on Programmer
PN/PL SUPPLY
K1 PROGRAM THERMOSTAT RELAY1
K2 COOLING/OVEN FAN RELAY2
K3 DOOR LOCK/UNLOCK RELAY3
PHV FUNCTION STATE
X0 THERMOSTAT ENCODER
X1 FUNCTIONS ENCODER
P4 PROBE
P5B WIRES P5B(1)+P5B(2)+P5B(3)
https://producthelp.fisherpaykel.com/us/Cook/Ranges/Electric/OR30SDPWSX1/User_Guide_OR30SDPWSX1/02_installation_instructions
Updated: Fri, 08 Mar 2019 10:04:01 GMT
Powered by
10