Fisher & Paykel DishDrawer DD24DTI User manual

integrated panel preparation
DD2¢STIand DD24DTI modeJs
Mod@lcs DD24STIet DD24DTI

Safety and warnings
Cut Hazard
Take care - pane[ edges are sharp°
Failure to use caution could result in injury or cuts°
Read these instructions completely and careful_yo
Ensure the product Lsnot plugged in.
Installation of DishDrawer ®panels requires basic mechanical and electrical skills.
Installation must comply with your local building and electfidty regulations.
Failure to instal_ the DishDrawer pands correctly could in validate any warranty or #abi#ty
claims.

Double models
P_educt p_epa_atien
Single models
P_educt preparation
Panel Installation
Badge CUtoOUt,handle and panel b_acket
Securing the panel b_ackets
Reconnecting the wires and fittin 9 the
panels and a custom toe kick (double modellso_"fly
6
7
8
Important!
SAVE THESEINSTRUCTIONS
i.!ixj{,< £:>ckcusr/,x#8 8,7y _/_8 f'>r ci.!':£,7 r)# si£ 8!;ols_ s_orWdc_.,d p8c/£{c1£>.,
8v<_iistiiit/h: y_>i/rcois _t04pk_ssmvisit oi.!/'icx:Ni >'/d>siiui/see, o: 18 _78{:/_{:ore/'
or {:o, _s{ /::>i/':io{8i 7s£8,"& i*:;//_d c88k*':

Product preparation
l_'_'_,_be l_s_;__, _,_nodes
ihdghtof
toekick
(12 ram)
The following calculations assume the top of the upper panel is aligned with the top of the
adjacent cabinetry. The final panel/cabinetry alignment is achieved by adjusting the feet:
width of ALL panels
Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,
then complete the equation.
door clearance panel width
heigh t of upper panelheight
standard height Bupper panel
heigh t of lower panel
Measure C(door/drawer height (or equivalent)) and write it in the first box below,
then complete the equation.
height height
C upper panel lower panel
(8n
Air gap
Note: The'door extension' B allows for the top of the upper panel to be above the DishDrawer ®where required.

Product preparation
Toe kick preparation
heigh t of toe kick panel
Measure D {height from the top of adjacent cabinet door fronts to the floor) and write it in the first
box below, then complete the equation.
heiqht
D B toe kite panel
(779 ram) (12 ram)
Toe kick options
The black prefinished toe kick panel is
supplied. This panel can also have a front panel
of your choice attached to it using screws or an
adhesive.
A toe kick panel of any material with thickness
3/8- 3_" (9 - 19 mm) can be screwed to the
plastic toe kick panel bracket (supplied).
Integrated Panel material max.
3/8- 1_6" (16 - 20 mm) panel thickness 2%"(67mm)
Adequately sealed to withstand moisture (122°F/50°C @80% RH)
_2s/8;'-5"
(67-127mm)
Toe kick
pane,
screws(5)
Panelpanel
screws(12) Integrated rectangular badge (2)
(Satinchrome supplied)
Toekick panel
bracket (1)
ket (2)
--<..
Prefinished Toe kick panel (1)

Product preparation
oi
inp'_ii_tio/ dic:;c,,_c:;zJs t,riii ss tmtio }o4 p,s s o 7£
The following calculations assume the top of the panel is aligned with the top of the adjacent
cabinetry.
width of the panel
Measure A (the width between adjacent door/drawer fronts) and write it in the first box below,
then complete the equation.
Adoor clearance panel width
+
height of the panel
Measure B(door/drawer height (or equivalent)) and write it in the first box below,
then complete the equation.
B panel height
_lr gap
Note: when the top of the DishDrawer ®has to be lower than the adjacent cabinetry, the panel can be increased
in height.

Product preparation
D_shDrawer®i_near floor...................level. _ ..............................
the
insta]hng*
UsethiS diagram I'f' -..............
Integrated Panel material
%- 13A6"(16- 20 mm) panel thickness
Adequately sealed to withstand moisture (122°F/50°C @80% RH)
Panelpanel
screws(6) Integrated rectangular badge (1)
(Satinchrome supplied)
Integ___
Panel

Badge cut-out,, handle and pane_ bracket
Important!
Ensure the product is not plugged in
5" (127 mm
10 _6"
255 mm
2 1_,, 54 mm
]" (127 rnm
i/
9 H
228.5 mm

Securing the pane_ brackets
Handles:
Important!
Ifmounting a handle: to avoid
damage, ensure fastenings
do not protrude beyond the
back surface of the panel.
Double models only:
Important!
Break off the tab at the top
of the Lower Panel Bracket

Reconnecting the wires and fitting the pane_s
and a custom toe kick (douMe mode_s on_y)
Important!
Ensure the rubber seal between the
drawer and panels is kept in place
,1%"(16 mm) X 5