Fisher & Paykel DishDrawer DD602I User manual

Fisher&Poykel
USA
ish TM
rawer
_ _..................
_;_> ........................
DD602 (Prefinished) DD602I (Integrated)
Part No. 599065/D

Section I
,]
.2
.3
.4
.5
.6
General Information
Preparation
Product Specifications & ( avity Dimensions
Ol)tious for Installing Multiple Products
Electrical, Plumbing & Drainage tnlormation
Product Parts
Additional Product Parts ior Integrated DishDrawer
Section 2
2.1
2.2
Foot Slide Retainer Information
Assembling the loot Slide Retainer
Sccuringthc lootSJidc Retainer
Section 3
3.t
3.2
3.3
3.4
3.5
Fitting the DishDrawer
( onuecting the Servi(:es
l texibJe [ xtrusiou Attachm(nt ior 24" by _4_/2'' (6t 0ram x 876mm) Cavity
Adjusting the leer
I ittiug the tmdl)iatc to the Chassis (OI)tiona[)
SccLirhlg the DishDrawc r
Section 4 Prefinished Toe Kick Installation
4.1 Setting the Lll)l)er Joe Kick l l(ight
4.2 i rimmiug the I ower foe Kick
4.3 irimmingthc loeKickPius
4.4 Adjusting the Upi)er loe Kick
_!!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_[_!;_!_
Section 8 Final Checks
8.1 h_stallation Wet test
8.2 t rouble shooting
Page DD O1

GENERAL INFORMATION
NOTE TO THE INSTALLER
• Be sure to leave these instructions with the ( uslomer.
• Ensure Ihis app[ian(e is properly grounded.
NOTE TO THE CONSUMER
• Keep these Installation Instm(tions with your Use & (are Manual for future
re f(,ren( e.
IMPORTANT
• Read thesu Instru(tions (ompleb, ly and (arefully.
• Observe all governing (:odes and Ordinances.
WARNING
• These Instructions are intencled as a guide only.
• It is the responsibility of the plumber and electrician to ensure that each installation
complies with all (::odes and Ordinances.
• Installation of this DishDrawer requires basic mechanical and electrical skills.
• The installer is responsible for the DishDrawer installation.
Improper installation is not covered under the Express Warranty Form.
IMPORTANT
• At the (ompletion of the DishDravw, r installation, the Installer must F)_,rforrn Final
Checks as per Section 8 of these Installation Instructions.
• Ensure the DishDrawer en( [osure is prepared for installation.
• Remove all pa(kaging and materials supplied with the DishDrawer.
• If you have any questions concerning the installation of this DishDrawer, contact:
Fisher & Paykel Customer Care Centre
TOLL FREE 1-888-9-FNP USA
TOLL FREE 1-888-9-36 7 872
Fax [phone]
WWW.FISHERPAYKEL.COM
27 Hubble
Irvine
(A 92618
USA
kl I _1'_ll IIPi U'{0) I]11[II I klRI:1111II[I!'_ I [0] _k'llRql:If-,Ivd111 I] k_l _l_kl [0] _ kl
CABINETRY DIMENSIONS
Height; 32 _6" - 341_s" [82Bmm-[380mm]
Width 23 _" (600ram}
Depth 22 _s" (580mm)
Service Hole 1 _" {38mm]
Electrical l 0=120 VA( (Water pressure below 7 p.s.i.
3 pin so( ke! ou![et (_0 kpa) may require lhe eleclmnics
Drying Residt!al Heat lo bP ,P-ptogramn_Pd by a SPtvicu
& Fan Assisted Putson at the time of installation)
Water Connection Re(ommended Hot
140% Max. (60°()
Water Pressure Maximum 139 p,sL (960 kpa)
Minimum 4.3 p.s.i. (30 kpa)
WARNING
Before installing the
DishDrawer, remove the
house fuse or open the
circuit breaker.
Ensure all water
connections are turned
OFF.
]WARNING
The DishDrawer MUST
be installed to allow for
future removal from the
enclosure if service is
required.
(50ram)
Page DD_02

-_ IMPORTANT
Where the DishDrawer
is installed under a
counter top, it is
recommended that bare
wood surrounding the
DishDrawer is sealed
with an oil based paint
or polyurethane to
prevent possible steam
damage.
[ l_] _O_I[O]_'J I_O]_ _l"_-'_llll_[e] v_LIIJlilll_ll_ I_i_O_ll_q_!
_ IMPORTANT
Ensure the cavity sides
are plumb (vertical) as
this will assist with
leveling the DishDrawer.
_ IMPORTANT
Ensure the Services Hole
is asclose as possible to
the rear lower corner of
the cabinetry. The hole
can be located on either
side depending on the
location of the services.
JIMPORTANT
On corner installations,
ensure that there is a gap
of 2" (50rnrn) minimum
between the adjacent
cabinetry and sides of
drawers.
(50ram)
Integrated or Prefinished Integrated or Prefinished
11- -II -II- 41 -"-
Integrated Models Only
[_ (are should be exercised when the appliance is installed or removed, to
reduce the likelihood of damage to the power supply cord.
If the power supply cord is damaged, it must be replaced by the Manufacturer, it ._Service
Agent or a simiJarJy quaJified person, in order to avoid a hazard.
The power supply receptacle for the appliance should be installed in a cabinet or on a wall
adjacent to the under (:()tinier space in whk:h the appJiance is to be installed.
The power supply receptacle should be positioned between 6" and 18"
(150ram and 450ram) from the cabinet opening of the DishDrawer.
%This appliance must be grounded. In the event of malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least
resistance I'or de(Irk: (urrenl.
This appliance is equipped with a cord having an equipment-grounding conductor and a
grounding pklg. The pklg roLlS[ be pJugged into an appropriate outJet that is installed and
grounded in accordance with all local (odes & Ordinances.
a)
b)
c)
d)
The water connection is to be made to a _ supply only. Ensure the water
temperature is not greater than i 40°F (60°().
A readily accessible shut off valve must be installed in the supply pipe.
The water supply pressure is to be between 4.3 p.s.i, minimum and 139 p.s.i.
maximum.
The inlet supply hose must be conne(ted to the water supply using a _/,"
compression type water supply fitting.
Ensure sealing washer supplied with connection hose is fitted.
Page DD_03

WASTE
HOT W#IER
WASTE
8" {200ram} MINIMUM
IO CONS] RAINING SURIAC[
Option 2
DishDrawer & Waste Disposal
POWER
OLJ[I El !
VALVE
Option 3
DishDrawer With Air Break
AIR BREAK
Note:
WASTE
WAS{E DISPOSAL
HOE WAFER
/_ 18" (200ram) MINIMUM
VALVE JTO ( ONSTRAINING SURFACE
Prefinished Model is shown. There is no variation in plumbing between Prefinished products
and Integrated products. Options 1 and 2 are the most preferred options.
"_ WARNING
Improper connection of the
equipment-grounding
conductor can result in a
risk of electric shock.
Check with a qualified
electrician or service
representative if you are in
doubt as to whether the
appliance is properly
grounded.
Do not modify the plug
provided with the
appliance -if it will not fit
the outlet, have a proper
outlet installed by a
qualified electrician.
"_ WARNING
The Drain Hose Support
must be at least 30"
(750ram) above the floor to
prevent siphoning of the
water during the wash
cycle.
It is recommended that the
Drain Hose Support is
secured in place using the
screw tab.
Ensure that the drain hoses
are fully extended.
Page DD_04

TOOLS NEEDED TO
INSTALL DISHDRAWER
wooden (hopping Board
Leve[
Safety (]lasses
UtiJity Knife
Pencil
DriJ[ & Drill Bits
(_/_2",Y,,"& '%2")or
(2.5mm, [2mm, I4mm)
Sandpaper
Tape Measure
Square
Ruler
Phillips Screwdriver
Pliers
Adjustable Wrenches (x2)
7/d' (6mm) Allen Key
(Inleg_aled Models)
• Router (Integ_aled Mo(h, ls
• Jigsaw (Inlegraled Models
Page DD_05
1.
i
©i
i
i
12.
16.
15. 17.
10.
T11.
13.
18.
1. Retainer (1)
(Channel Transverse)
2. Slide Runners (2)
(Channel Longitudinals)
3. Foot Slide Template (i)
4. Clip Pegs (2)
5. Toe Kiek Pins (2)
6. Toe Kick Brace (i)
7. Lower Toe Kick (t)
8. Serews (t 1)
9. Drain I lose Support (1)
10. Wire Clips (2)
11. Drain Hose Joiner (t)
12. Edge Proteetor (t)
13. Flexible Extrusion (3)
14. Solderless Lug & Washer
15. Inlet ttoseWasher (I)
16. Transit Pa(ker (t)
17. Masonry An(hors (2)
18. Hose (;lamp (t)
19. Endplates (2)
20. Small Serews (I4)
21. Badge Kit (2)
22. Mounting Braeket Nuts (8)
23. Door Serews (8)
24. Seal (2)

FOOT SLIDE RETAINER INFORMATION
The Foot Slide Retainer is made up with one Retainer and two Slide Runners. The
Toe Kick Brace is NOT used in the Foot Slide Retainer.
2.1.1
Bend the tabs at both ends of the
Retainer so they fit the width of the
cavity for the DishDrawer.
2.1.2
Assemble the Foot Slide Retainer by
fomling three sides of a square with the
Retainer and Slide Runners as shown,
ensuring that they fit together. Place in
the cavity.
2.1.3
Using the front of the cavity, create a
center point.
2.1.4
Place the Template in the cavity
ensuring that the template is sitting flat
and lines up with your center point.
]IMPORTANT
It is important that the Foot
Slide Retainer is correctly
installed. It guides the
feet back and holds the
rear of the DishDrawer
down to prevent it rocking
forward when the drawers
are opened. It also aligns
the product to the cavity
front.
l_ WARNING
Be careful of sharp edges.
]IMPORTANT
If there is a drop :]own in
the cavity, you may have
to build the cavity up
level with the finished
floor.
Page DD_06

[_ IMPORTANT
For Integrated product
with door thickness other
than s/4" (I 8ram), the
Foot Slide position must
be adjusted forward or
back to allow for this
difference.
_ IMPORTANT
Check for any protrusions
that may interfere with
the DishDrawer sliding
back into the cavity and
allow for these.
_ IMPORTANT
The Foot Slide Retainer
must be adequately
secured to prevent
movement.
2.1.5
Position the Foot Slide' Retainer within the
(:uloul areas of the Template.
2.1.6
The Tempiate should be pla(efl in the (avit,
undl the wings just touch the existing
cabinetry. This ensures the front of the
DishDrawer wiii be flush with the existing
cabinetry.
Correct ,_ Incorrect
There are b_vooptions available for securing the Foot Slide Retainer. Either option is
adequate for securing the DishDrawer. Using both options together is optimum.
2.2.1
The first and preferred option is to screw the
Retainer to the floor. The tabs can be broken
off at the perforations, if they are not used.
2.2.2
The second option is to screw the Retainer
to the cabinet sides.
2.3.3
Masonry Anchors are supplied with the
accessories to replace the long screws if
attaching the Foot Slide Retainer to
concrete flooring.
Masonry Anchors should not be used if there
is any chance of damaging underfk)or
heating.
Page DD_07

FITTING THE DISHDRAWER
3.1.1
Feed the Power (ord, Inlet Hose and
Drain Hoses through the Services Hole.
Position the DishDrawer in front of the
opening.
3.1.2
( onne(t the Inlet Hos_' to the HOT
WATER SUPPLY. Ensure sealing washer
supplied with the accessories is fitted.
Hose coupling nlLISt be tightened a furlher
half turn after seal contact.
3.1.3
If required, the Drain Hose may be
trimmed to a suitable length.
3.1.4
If an air break option is not chosen, then
the Drain Hose Support nlust be clsed and
positioned at least _0" (750rnm) above
the Iloor to prevent siphoning of the water
during the wash (y( le. (See Step 7.4 -
Eh, clrical, Plumbing & Drainage
Inf_Jrmalion.)
3.1.5
When using a standpipe option, hoses
should not extend further than 2" (50ram)
down the standpipe in order to prevent
siphoning.
3.1.6
If required, trim the Drain Hose Joiner to
the size whkh mak hes the, waste te_, or
air break to be used. There are ribs
provided to guide cutting.
When using the Drain Hose Joiner, the
hoses should be pushed in firmly, 5
cNeks.
Li-
3.1.7
Atta( h the Drain Hose Joiner to the waste
tee(see StPp 1.4). Ensure a snug fit, using
the hose (lamp supplied.
The supplied Wire Clips should be
installed between the two positioning ribs
on the Drain Hose Joiner.
Remember to slip the Wire Clips over the
Drain Hoses be{ore connecting to the
Drain Hose Joiner.
]WARNING
Ensure the edges of the
Services Hole are smooth
or covered. (See Step 1.2 -
Product Specifications &
Cavity Dimensions.) If the
Services Hole is through a
metal partition, the hole
must be protected with the
Edge Protector provided.
_ WARNING
DO NOT adjust the
length of the Inlet Hose.
TIP
Turn the water valve ON
to check for any leaks,
before pushing the
DishDrawer back into its
cavity.
_-_ WARNING
Attach the Drain Hose
Support to the cabinet
joinery to prevent
siphoning and keep the
drain hoses from kinking.
Page DD_08

_WARNING
The Product must not be
plugged in at this stage.
_ WARNING
If permanently
connecting, ensure
power is isolated
TIP
WMng, Plumbing and
Services should be
completed before
attaching the flexible
extrusion.
Page DD_09
Neutral
Live
Ground
3.1.8
Ensure there is a power outlet in reach of the
supplied flex. If there is not a suitable outlet
available then have one installed by a
qualified electrician.
DO NOT modify the power plug supplied
with the DishDrawer or use an extension
c:ord, adaptor plug or muhiple outlet box.
3.1.9
Ahernativeiy, file DishDrawer may be
permanently c onnectud to flexible conduit.
Remove the flex and cable clamp. Fit
suitable cable c:lamp for the (:onduit and
terminate the wiring as shown.
Use the solderless lug and washer supplied
with the produ(:l parts k) terminate the
ground wire.
3.2.1
Flexible Extrusions are supplied to enable
the installer to help fill any excess spac:e
between the sides and top of the
DishDrawer and the cavity. The three
lengths of Flexible Extrusion (supplied)
should be attached before pushing the
DishDrawer into the cavity for final
installation. The Extrusions are designed
to fit a 24" width by 34_//' high cavity
(6i0mm x 876mm).
3.2.2
Open the drawers, exposing the c:hassis
trim.
3.2.3
Remow, backing from adhesive tape on
Flexible Extrusion. The larger of the
Extrusions is used to fill the gap at the top
of the product.
3.2.4
Apply as per drawings, ensuring the
(:urved edge of the Flexible Extrusion fits
around the corner of the chassis [rinq.
3.2.5
When (he(king final fit, ensure the
DishDrawer is centered and there are
even tolerances between the DishDrawer
and cavity.