Fisher & Paykel DH9060HG1 User manual

INSTALLATION GUIDE
NZ AU
FABRIC CARE SOLUTION
DRYER INSTALLATION
DH9060HG1 and DH9060H1 models

2
COMPONENTS REQUIRED
TOOLS
PARTS
Not supplied
F Box cutter
F Phillips screwdriver
F Level
Supplied
F 1x Y Join
F 1x Straight hose
F 1x Cold water hose
F 1x Shoe Rack
F 3x Spare condenser foam filters
F 1x Drain hose extension
(display models only)

3
ACCESSING YOUR PRODUCT SPECIFICATIONS
For full product, cabinetry and service specifications, refer
to the Planning Guide. To access the Planning Guide, scan
the QR code or visit fisherpaykel.com/specify. Search by
appliance type, product name or model code.
862
665
624

4
PRIOR TO INSTALLATION
3. Ensure power will remain
accessible following install to
allow access for any future
product maintenance.
Service holes should be smooth
with gromets installed where
required.
Refer to the services section
of the Planning Guide for more
details.
2. Ensure floor is level and clear
and a finished return has been
created.
1. Ensure cabinetry and
servicing specifications have
been met and clearances have
been considered.
Refer to the Planning Guide for
details.
fisherpaykel.com/specify

5
UNPACK
3. Protect flooring before
positioning dryer as close to
the installation location as
possible, ensuring enough
working room is left available.
1. Cut the straps and the line
printed on the top of the
carton. Lift to remove. Discard
braces and corner posts.
Remove any packaging and
accessories from the drum and
base packer.
2. Dispose of packaging
responsibly.

6
REVERSE DOOR (OPTIONAL)
1. Unscrew hinge, remove door
and place face down on a
protected surface.
Remove plugs (x 8) from inner
door flanges, then remove
screws.
2. Insert flathead screwdriver
in access slot to pry off inner
door. Rotate door 180 degrees
and fit back in place.
Reattach screws, alternating
between sides of the door.
Replace plugs.
3. On dryer, unscrew and
remove latch cover to access
latch.
The dryer door has reversible hinge and latch fittings and can be switched to open to the
left or right, as needed.

7
REVERSE DOOR (OPTIONAL)
4. Unscrew latch, and slide to
remove.
5. Rotate latch and insert on
opposite side of dryer. Secure
with screw.
Refit and secure latch cover
with latch cover screws.
6. Refit door hinge and secure
with hinge screws.

8
LEVEL
2. Move the dryer into its final
position, allowing for required
clearances.
1. Adjust the feet until the
dryer is level front to back and
corner to corner.
3. Recheck dryer is level, then
remove from the alcove to
complete connection steps.

9
CONNECT CABLES AND HOSES
2. Optional:
Fit the drain hose extension if
dryer can be connected to a
drain.
1. Refer to the Planning Guide
for full service information.
Supply: 220 - 240V, 50Hz
Service: 10A
Outlet: 3-prong grounding-type
Supply: Hoses provided
Pressure: 50KPa (7psi) - 1MPa
(150psi). Min 6 litres/min.
fisherpaykel.com/specify
3. Connect the angled end
of the dryer cold hose to the
dryer.
The washer and dryer cold
hoses can be swapped if
necessary.

10
CONNECT CABLES AND HOSES
4. Turn off cold water tap for
washer, and undo washer cold
hose at tap end.
5. Connect washer and dryer
straight ends to the top of the
supplied Y join.
6. Connect the dryer straight
hose to the bottom of the Y
join.

11
CONNECT CABLES AND HOSES
7. Partially push dryer into the
alcove.
8. Route the power cables and
hoses through service holes.
Ensure power will remain
accessible following install to
allow access for any future
product maintenance.
9. Connect the cold hose to
cold water tap and turn tap on.

12
CONNECT CABLES AND HOSES
10A. Standpipe Installations
Route the drain hose through
the guide and place into the
standpipe.
Ensure a maximum of 20mm of
the hose rests in the standpipe.
10B. Spigot Installations
Drill out blanking insert from
the spigot.
Route the drain hose through
the guide and place into the
spigot. Secure using a hose
clamp.
11. Connect the power cable
and check product is powered
on.

13
1. Push dryer into the alcove.
Take care not to damage hoses
or cords.
2. Check alignment and
ensure required clearances are
maintained. Adjust as required.
INSTALL DRYER

41188A 09.2
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2023. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher&Paykel dealer.