Fisher & Paykel ELBA OB60SC User manual

Built-in Oven
OB60SC Single models
NZ AU
INSTALLATION INSTRUCTIONS
590913 C 10.15

1
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to
our website listed on the cover or contact your local ELBA by Fisher & Paykel dealer.
IMPORTANT SAFETY INSTRUCTIONS
 To avoid hazard, follow these instructions carefully before installing or using this
appliance.
 Please make this information available to the person installing the appliance - doing so
could reduce your installation costs.
 This appliance must be installed and connected to the mains power supply only by a
suitably qualified person according to these installation instructions and in compliance
with any applicable local building and electricity regulations. Failure to install the
appliance correctly could invalidate any warranty or liability claims.
 If the power supply cable is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified person in order to avoid a hazard.
 Isolating switch: make sure this oven is connected to a circuit which incorporates an
isolating switch providing full disconnection from the power supply in accordance with
the local wiring rules.
 The oven must be earthed.
WARNING!
Electrical Shock Hazard
Always disconnect the appliance from the mains power supply before
carrying out any maintenance or repairs.
Connection to a good earth wiring system is essential and mandatory.
Alterations to the domestic wiring system must only be made by a
qualified electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Hot Surface Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Fire Hazard
Do not use adapters, reducers, or branching devices to connect this appliance
to the mains power supply.
Failure to follow this advice may result in overheating, burning, or fire.
!
!
!
1SAFETY AND WARNINGS

2
2PRODUCT DIMENSIONS (TOP OPENING MODELS)
A
C F
B
E
G
H
I
J
K
D
L
M
Electrical supply 16-20 mm
FRONT SIDE
TOP
OB60SC
white
models
OB60SC
stainless steel
models
PRODUCT DIMENSIONS MM MM
AOverall height of product 595 595
BOverall width of product 595 595
Coverall depth of product (excluding handle and knobs) 565 569
DHeight of chassis 575 575
EWidth of chassis 552 552
FDepth of chassis 545 545
GDepth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs)
20 24
HDepth of oven door when fully open
(measured from front of control panel)
450 450

3
2CABINETRY DIMENSIONS (TOP OPENING MODELS)
A
C F
B
E
G
H
I
J
K
D
L
M
Electrical supply 16-20 mm
TOPSIDE
OB60SC
white
models
OB60SC
stainless steel
models
CABINETRY DIMENSIONS MM MM
IMinimum inside width of cavity 560 560
JOverall width of cavity 600 600
KInside height of cavity 580 580
LOverall height of cavity 600 600
MMinimum inside depth of cavity 550 550
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s
instructions.

4
2PRODUCT DIMENSIONS (SIDE OPENING MODELS)
A
C F
B
E
G
H
I
J
K
D
L
M
Electrical supply
16-20 mm
FRONT SIDE
TOP
OB60SC
side opening
models
PRODUCT DIMENSIONS MM
AOverall height of product 595
BOverall width of product 595
Coverall depth of product (excluding handle and knobs) 569
DHeight of chassis 575
EWidth of chassis 552
FDepth of chassis 545
GDepth of oven frame and control panel
(=distance between front of chassis and front of oven door, excl. knobs & door hinge)
24
HMaximum Depth of oven door when fully open
(measured from front of control panel)
590

5
2CABINETRY DIMENSIONS (SIDE OPENING MODELS)
OB60SC
side opening
models
CABINETRY DIMENSIONS MM
IMinimum inside width of cavity 560
JOverall width of cavity 600
KInside height of cavity 580
LOverall height of cavity 600
MMinimum inside depth of cavity 550
Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer’s
instructions.
IMPORTANT!
Doors of adjacent
cabinetry may need
adjusting to allow
the oven door to
open properly: a
minimum clearance
of 2.5mm is
recommended.
A
C F
B
E
G
H
I
J
K
D
L
M
Electrical supply
16-20 mm
SIDE TOP

6
3PRIOR TO INSTALLATION
Before you install the oven, make sure that
 the benchtop and oven cavity are square and level, and are the required dimensions
 the installation will comply with all clearance requirements and applicable standards and regulations
 a suitable isolating switch providing full disconnection from the mains power supply is incorporated in the permanent wiring, mounted and positioned to comply with the local wiring rules and
regulations. The isolating switch must be of an approved type and provide a 3 mm air gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules allow for
this variation of the requirements)
 the isolating switch will be easily accessible to the customer with the oven installed
 there is at least 1.5 m (and not more than 2 m) free length of power supply cable within the cavity for ease of installation and servicing
 the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall
 the oven will rest on a surface that can support its weight
 the height from the floor suits the customer
 you consult local building authorities and by-laws if in doubt regarding installation
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
IMPORTANT!
Do not lift the oven by the door handle.
 Remove the accessories box from on the top of the oven and set aside.
 Remove all packaging (and dispose of it responsibly. Recycle items that you can.
 Place the unpacked oven onto wooden blocks or similar supports to prevent damaging the
lower edge of the oven.
 Depending on the model, the door is either left- or right-hinged. When
determining the location of the oven, ensure there will be enough space for the
door to open to its full extent.
IMPORTANT!
To access the fixing screw location above the door hinge, you need to position
the screw/screwdriver at an angle. Although not recommended, if you are
unable to access the fixing screw at an angle, the door can be removed first.
To remove the door:
1Unscrew the four screws on the
inside of the door hinge, as shown.
2Carefully remove the door
and lay on a flat surface.
Be careful not to
damage or scratch
the glass.
4 Inner door hinge
screws
Securing Screw location
above door hinge
Securing
Screw location
4UNPACKING THE OVEN 5OVEN LOCATION (OB60SC SIDE OPENING MODELS ONLY)
Lower edge
IMPORTANT!
When you remove the oven from
the carton be careful not to damage
the lower edge which is important
for both ventilation and excess
condensation.
1
2

7
6ELECTRICAL CONNECTION 7SECURING THE OVEN TO THE CABINETRY
IMPORTANT!
 This oven must be connected to the mains power supply only by a suitably qualified
person.
 This oven must be earthed.
Before connecting the oven to the mains power supply, check that
 the domestic wiring system is suitable for the power drawn by the oven
(as specified on the rating plate)
 the voltage corresponds to the value given on the rating plate.
1Position the oven in the prepared cavity.
IMPORTANT!
Do not lift the oven by the door handle.
2Open the oven door fully.
3Mark and pre-drill the screw holes.
4Use the supplied screws to secure the oven to the cabinetry.
IMPORTANT!
 Do not over-tighten the screws.
 Do not seal the oven into the cabinetry with silicone or glue. This makes future servicing
difficult. Fisher & Paykel will not cover the costs of removing the oven, or of damage
caused by this removal.
(OB60SC SIDE OPENING MODELS ONLY)
To replace the door
(if previously removed)
1Fit the door back onto the hinge
and replace the four inner
screws holding it in place.
IMPORTANT!
 Ensure the screws shown are
correctly located and fully
tightened.
 Ensure the door is correctly
aligned and gaps around the
door are consistent.
Unclip
and lift up
L1N(L2)E
Brown
(Live)
Ensure cable
clamp is tightened
with screw
(you may have
to remove the
screw rst
before tting
the clamp)
L
N
Green
& Yellow
(Earth)
Blue
(Neutral)
Oven may vary
MODEL CODE MAX POWER (W) HZ VOLTAGE (V) AMPS (A)
OB60SC... 3000 50 Hz 220 - 240 V~ 13
4 Inner door hinge
screws

8
8FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Make sure the oven is level and securely fitted to the cabinetry.
Check the lower trim is undamaged.
Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim.
This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the oven door opens fully without obstruction.
Make sure you remove all internal packaging.
Make sure all oven vents and openings are clear and free of any obstruction or damage.
IMPORTANT!
Failure to make sure all oven vents are clear may result in poor product performance.
Make sure that the isolating switch is easily accessible by the customer.
TEST OPERATION:
Turn the power to the oven on. On some models, the display should light up and show 0.00.
Check the oven is working:
 Set the clock (some models only). See the User Guide for instructions on how to do this.
 Select the Bake function and set the temperature to 50 0C.
 Wait 10 minutes. Has the oven has warmed up?
 Switch the oven back off.
Advise the customer to follow the instructions in their user guide in section ‘First use’.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date