Fisher & Paykel Aerotech OS302 User manual

599193B 6/2006 NZ & AU
Installation Instructions
NZ & AU
OD302
OD302M
OS302
OS302M

2
OS302M
718mm
570mm
757mm
675mm
530mm
688mm
595mm
681mm
762mm
20mm
16-20mm

3
OD302M
1217mm
1230mm
595mm
1222mm
762mm
757mm
530mm
718mm
20mm
570mm
16-20mm

4
Warnings & safety information
WARNING
Cut Hazard
Take care - panel
edges are sharp.
Failure to use caution
could result in minor
injury or cuts.
Before you start
Ensure a suitable disconnection switch
is incorporated in the permanent wiring,
mounted and positioned to comply with
the local wiring rules and regulations. A
means of disconnection with at least a
3mm air gap contact separation in all poles
must be incorporated into the fixed wiring
in accordance with the wiring rules, unless
the local wiring rules allow for the following
variation. A means of disconnection from
the supply having an air gap separation
in all active (phase) conductors must be
incorporated in to the fixed wiring.
We recommend that the outlet for the
electrical supply cable is located in the
right rear corner of the cabinet cavity.
This allows the electrical supply cable to
sit inside the rear chamfered corner of
the oven and prevents it being jammed
between the cabinet wall and the rear of
the oven.
Ensure the benchtop and the oven cavity
are square and level.
The oven support surface should be flat,
level and be able to support a weight of at
least 190kg for double oven models and
108kg for single oven models.
Ensure the electrician provides sufficient
free length of mains cable to reach from
the bottom rear of the cavity to at least 1.5
metres in front of the bottom edge of the
opening. The cable may enter the cavity
from the side, top or bottom, but top entry
must be at the rear of the cavity.
Use easy to clean finishes for the wall
surfaces surrounding the oven and cooktop
to aid in removal of any cooking fume
staining resulting from the use of the oven
and cooktop.
Check the height from the floor suits the user.
Ensure that drawers and doors will be clear
of obstruction when fully opened.
CAUTION!
In order to avoid hazard these products
must be installed according to these
instructions.
Please follow installation information
carefully. If in doubt consult your local
building authority by-laws.
Failure to install the product correctly
could invalidate any warranty or liability
claims.
The product is to be installed only by an
authorised person.
IMPORTANT!
Please make this information available
to the person responsible for installing
the product as it could reduce your
installation costs.
Read these instructions carefully before
installing or using this product.

5
Installing a cooktop above a
Titan oven
If installing a cooktop above the oven
ensure adequate clearance is provided
for the cooktop as per the Cooktop
Manufacturers Instructions.
Customer care
For contact details please refer to your
Service and Warranty book or visit
www.fisherpaykel.com
Flush mounting options
Installation instructions
Installation instructions
1 Check that the oven cavity is square
and within the limits in the installation
dimensions.
2 Remove the mains wiring access cover.
3 Connect the mains wiring and replace the
access cover.
Ensure the product is bonded to earth.
4 Remove the oven door and accessories, lift
and slide oven into place. When installing
the oven it is essential to centre the
product in the cavity giving a spacing of
2.5mm from the door edge to the joinery
5 Secure oven in cavity using the four wood
screws and washers supplied through the
enamelled frame at either side of the oven
as shown in the flush mounting options.
6 Test then refit the door and accessories,
check that the oven is firmly secured in
the kitchen unit.
Wiring Connection
Minimum temperature rating of the supply
cord must be at least 90oC.
20mm
2.5mm
DRAWER FRONT
20mm
2.5mm
CUPBOARD FRONT
20mm
2.5mm
Maximum current draw and Maximum Load:
Double: 38.2 A 9.2 kW 35 A 7.7 kW
240V 220V
Single: 21 A 5.1 kW 19.5 A 4.3 kW
220...230V~
PEL1
1 2 3 5
N (L2)
4
380...400V 3N~
PE
L1
1
N
4
L3
3
L2
2 5