Fisher & Paykel OB60SDPT User manual

OB60SDPT models
BUILT-IN OVEN
INSTALLATION GUIDE
NZ AU GB IE
591942A 07.19

2
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• Before carrying out any work on the
electrical section of the appliance, it must
be disconnected from the mains electricity
supply.
• Connection to a good earth wiring system is
absolutely essential and mandatory.
• Alterations to the domestic wiring system
must only be made by a qualified electrician.
!WARNING!
Fire Hazard
Failure to follow this advice may result in
overheating, burning, and injury.
• Do not use adapters, reducers, or branching
devices to connect this appliance to the
mains power supply.
!WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to
change at any time. For current details about model and specification availability in your country,
please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
WARNING!
To avoid hazard, follow these instructions carefully
before installing or using this appliance.
• Please make this information available to the person
installing the appliance—doing so could reduce your
installation costs.
• This appliance must be installed and connected to
the mains power supply only by a suitably qualified
person according to these installation instructions and
in compliance with any applicable local building and
electricity regulations. Failure to install the appliance
correctly could invalidate any warranty or liability claims.
• If the power supply cable is damaged, it must be
replaced by the manufacturer, its service agent or
similarly qualified person in order to avoid a hazard.
• Isolating switch: make sure this oven is connected to a
circuit which incorporates an isolating switch providing
full disconnection from the power supply in accordance
with the wiring rules.
• The oven must be earthed.
• Do not use adaptors, reducers or branching devices to
connect the oven to the mains electricity supply, as they
can cause overheating and burning.
• The appliance must not be installed behind a decorative
door in order to avoid overheating.
• Please take extra care not to damage the lower trim of
the oven during installation. The trim is important for
correct air circulation and allows the door to open and
close without obstruction. The manufacturer does not
accept any responsibility for damage resulting from
incorrect installation.
SAFETY AND WARNINGS

3
Screws (2) Metal side shelves
fixing nut (2)
Ensure that:
the countertop and oven cavity are square and level, and are the required dimensions
the installation will comply with all clearance requirements and applicable standards and regulations
the isolating switch will be easily accessible to the customer with the oven installed
the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1.5 metres in front of the bottom edge of the opening
the cable may enter the cavity from the side, top or bottom, but top entry must be at the rear of the cavity
the oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear wall
the oven will rest on a surface that can support its weight
the height from the floor suits the customer
you consult local building authorities and by-laws if in doubt regarding installation
IMPORTANT!
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or
excessive condensation, we recommend moisture-proofing the oven cavity.
zzthe oven door can open fully without obstruction.
zzthe power supply cable does not touch any hot metal parts.
zzthe isolating switch is easily accessible to the customer with the oven installed.
zzyou complete the ‘Final checklist’ at the end of the installation.
zzIf, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Centre, Customer Care, or contact us
through our local website listed at the end of this document.
PARTS SUPPLIED
PRIOR TO INSTALLATION
AFTER INSTALLATION

4
PRODUCT DIMENSIONS
OB60SDPT MODELS
MM
A Overall height of oven 598
B Overall width of oven 596
C Overall depth of oven (excluding handle and dials) 565
D Height of chassis 575
E Width of chassis 556
F Depth of chassis 545
G Depth of oven frame and control panel
(distance between front of chassis and front of oven door, excl. handle and dials) 20
H Depth of oven door when fully open
(measured from front of control panel) 460
PRODUCT DIMENSIONS
a
c
f
g
d
e
h
FRONT
PLAN
PROFILE

5
CABINETRY DIMENSIONS
OB60SDPT MODELS
MM
A Minimum inside width of cavity 560
B Overall width of cabinetry 600
C Minimum inside height of cavity 580
D Overall height of cabinetry 600
E Minimum inside depth of cavity 550
If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manufacturer’s instructions.
CABINETRY DIMENSIONS
PROUD INSTALL
FLUSH INSTALL
16-20mm
16-20mm
2mm
PROFILE PLAN
e
b
a
c d

6
Remove the accessories box from
the top of the oven and set aside.
Recycle responsibly
DISCARD PACKAGING RESPONSIBLY

7
IMPORTANT!
zzThis oven must be connected to the mains power supply only by a suitably
qualified person.
zzThis oven must be earthed.
Before connecting the oven to the mains power supply, check that:
the domestic wiring system is suitable for the power drawn by the oven (as specified on
the rating plate)
the voltage corresponds to the value given on the rating plate.
CONNECT THE OVEN TO THE MAINS SUPPLY
L1N(L2) E
L1N(L2) E
MODEL CODE MAX POWER (W) HZ VOLTAGE (V) AMPS (A)
OB60SDPT 2800 - 3300 50 Hz 220 - 240 V~ 12.8 - 13.8
Brown (Live)
Blue (Neutral)
Green & Yellow (Earth)
Ensure cable
clamp is
tightened
Unclip
and lift
SECURE THE OVEN TO THE CABINETRY
IMPORTANT!
zzDo not lift the oven by the door handle.
zzDo not over-tighten the screws.
zzDo not seal the oven into the cabinetry with silicone or glue.
This makes future servicing difficult. Fisher & Paykel will not
cover the costs of removing the oven, or of damage caused
by this removal.
1 Position the oven in the prepared cavity.
2 Open the oven door fully.
3 Mark and pre-drill the screw holes.
4 Use the supplied screws to secure the oven to the cabinetry.

8
TO BE COMPLETED BY THE INSTALLER
Ensure the oven is level and securely fitted to the cabinetry.
Check the lower trim is undamaged.
Open the oven door slowly until it is fully open and check there is adequate clearance
between the bottom of the door and the lower trim.
This is to ensure correct air circulation. Should the lower trim become damaged,
straighten the trim and ensure the oven door opens fully without obstruction.
Ensure you remove all internal packaging (including the circular yellow packing retainers
holding the accessory box in place).
Ensure all oven vents and openings are clear and free of any obstruction or damage.
IMPORTANT!
Failure to make sure all oven vents are clear may result in poor product performance.
Ensure the isolating switch is accessible by the customer.
TEST OPERATION:
Turn the power to the oven on. The display should light up.
Set the clock following the instructions in the ‘User guide’.
Set the oven to Bake at 50oC. The light should come on inside the oven cavity and air
should blow out of the vent at the top of the oven. After five minutes, open the oven
door: the air inside should feel warm. Turn the oven off.
Have you demonstrated the basic operation to the customer?
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
INSTALLER CHECKLIST