Lamp Replacement
Parts & Service
a)Switch off the power to the rangehood.
b)Use a small bladed screwdriver to prise off the light cover (note slot).
c) Use a cloth to remove the bulb. Do not touch the bulb with fingers.
d)Replace with a new bulb and “snap” the cover back into place.
e)Halogen bulb 12Volt/20Watt required.
BULB
NOTE: TAB ON
BOTH SIDES TO BE
BENT IN TO LOCK
DUCT IN PLACE
SEE DETAIL1
Rercirculating
Kit 89504
104385 issue H
ECN: 04 036
Electrical Rating:
346W (1.44A)
Max. at 230-240V 50Hz
RECOMMENDED UNIDUCT DUCTING
SYSTEMS FOR RANGEHOODS
WARNING
•This appliance is not intended for use by young children or infirm persons
without supervision.
•Young children should be supervised to ensure that they do not play with
the appliance.
•There shall be adequate ventilation of the room when the rangehood is
used at the same time as appliances burning gas or other fuels.
•You must read the details concerning the method and frequency of
cleaning.
•There is a fire risk if cleaning is not carried out in accordance with the
instructions.
•Do not flambé under the rangehood.
•Exhaust air must not be discharged into an existing flue which is used
for exhausting fumes from appliances burning gas or other fuels.
•The minimum distance between the hob surface and the lowest part of
the rangehood is 600mm. This distance shall be at least 650mm
(recommended 700mm) if the rangehood is installed over a gas hob.
•Attention should be given to ensure that any applicable regulations
concerning the discharge of exhaust air is fulfilled.
•If the supply cord of this equipment is damaged, it must only be replaced
by the manufacturer or its service agent or similarly qualified person in
order to avoid a hazard.
WARNING: The distance between the hob and the mounting holes of the canopy to be
at least 900mm to ensure that the fully installed canopy has a clearance of
700mm (recommended height) between the lower part of the hood and the
cooking hob. Before drilling any holes check the wall and the ceiling are clear of
any electrical cables, pipes etc. Fixing to a solid stud is recommended. A
Fix the mounting washers in position shown in diagram. 1 Check with spirit level
accross the washers to ensure they are level.
INSTALLING DUCTING
NOTE: All ducting must comply with local requirements and building codes.
Mark the position of decorative chimney at ceiling and wall, cut cornice moulding
away if necessary to enable panels to fit flat against the wall and ceiling. 2 Mark
and cut the hole in the ceiling to fit the ducting (155 to 160mm dia). 3 This is
positioned centrally with the canopy and 100mm from the wall.
INSTALLING CEILING BRACKET
Using the supplied screws, fix the ceiling bracket 4 to the wall, checking that it is
aligned with the hood.
FINAL ASSEMBLY
Remove protective plastic covering from all parts including filters.
Now fit the canopy on the fixed mounting washers. 5 Plug in power
cord at power supply. Check function of rangehood light and motor,
before continuing assembly. Fix safety screw 5 connect 150mm
ducting 6 to top of motor flange secure with cable tie. Assemble
the telescopic ducting covers (chimney) 7 to accurately suit the
dimension required, 8 fit black plastic extrusion to the base and top
of the chimney and cut to length. 9 Mounting screws and plastic
cover caps are applied on top and bottom of the chimney.
INSTALLATION OF THE UNIT
TOP
GUIDE
RECIRCULATING
DUCTING
RECIRCULATING
OPTION
DUCTING
OPTION
200mm
A
700mm
UNDERSIDE OF HOOD
TO COOKING SURFACE
2.4 TO 2.65 METRE HIGH CEILING
6
FILTERS
Aluminium Filter - No. R104163 (Ducted models)
Charcoal Filter No. R104165 (Recirculated models)
The use of charcoal filter is recommended on
recirculating model rangehoods.
DUCTED
UNIDUCT FLEXI DUCT FIT is recommended.
1569 Flexi Duct Kit (150mm)
RECIRCULATED
Use manufacturer Part No. 89504
For other Accessories, Parts or Service, please contact your local supplier.
(Refer to the Warranty Certificate)
DETAIL 1
MANUFACTURED FOR
BY:
ROBINHOOD LIMITED
6 ZELANIAN DRIVE, EAST TAMAKI
AUCKLAND, NEW ZEALAND
ISO9001 Certified
