Fisher & Paykel HC60PHTX1 User manual

Installation instructions
Details the various product and cabinetry dimensions of your rangehood and everything else you need to need to know
prior to installing your rangehood.
Contents of packaging
Rangehood hood (1) Installation instructions User guide manual
(1)
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
1

Upper chimney (1)
Upper chimney bracket (1) Chimney bracket (1)
150 mm diameter ducting adapter (1)
Expansion plug (10) 30 mm self-tapping screw (10)
10 mm self-tapping screw (4)
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
2

Product dimensions
Product Dimensions HC60PHTX1 HC90PHTX1 HC120PHTX1
A. Overall height of product (mm) 655 – 1094 655 – 1094 655 – 1094
B. Overall width of product (mm) 598 898 1198
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
3

Product Dimensions HC60PHTX1 HC90PHTX1 HC120PHTX1
C. Overall depth of product (mm) 500 500 500
D. Height of product (mm) 113 113 113
E. Width of chimney (mm) 320 320 320
F. Depth of chimney (mm) 290 290 290
G. Distance from centre of ducting outlet to
back of product (mm) 95 95 95
H. Distance from centre of ducting outlet to
side of chimney (mm) 160 160 160
I. Diameter of ducting outlet (mm) 150 150 150
J. Distance between centre of lights (mm) 1 light in
centre N/A
2 lights on
sides 820
3 lights (2 on sides, one
in centre) 558
K. Distance between lights to back of
product (mm) 50 – 430 50 – 430 50 – 430
Length of power cord (mm) 800 800 800
Actual product dimensions may vary by ± 2 mm.
Please read the entire instructions before installing the rangehood.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
4

Height of rangehood
Installation Dimensions mm
L. Installation height
• Ducted
• Recirculation
min. 680 – max. 1094
min. 720 – max. 1094
H. Height top of cooktop to base of product min. 660 – max. 750
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
5

• Rangehood installation height above the cooktop is the user’s preference.
• Lower installation heights will improve the efficiency of capturing cooking odours, grease, and
smoke. This rangehood must be installed between the minimum and maximum dimensions
indicated in the table above.
Venting options
Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are fulfilled.
The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to operate
with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 150 mm diameter, rigid or semi-rigid ducting is used. This will
require a 160 mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.
For optimal efficiency use the shortest and straightest duct route possible and use rigid or semi-rigid ducting for
reduced noise and increased airflow. Flexible metal ducting should only be used as a last resort (ie in difficult
installations) and if used ensure that it is straight and smooth and extended as much as possible.
Recirculating
To enable the product to operate with the air recirculating, please purchase a recirculation diverter and carbon
filters (refer to the ‘Parts and accessories’ section). This recirculation diverter is installed after a short length of
ducting and is required to channel the air out the side vents at the top of the chimney and the carbon filters are
required to remove odours.
A ducting hole is not required in the wall or ceiling if the rangehood is installed to operate
with exhaust air recirculating.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
6

Installation
•This appliance is heavy and requires two persons for unpacking and installation
•Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards.
•Failure to install the screws or fixing device in accordance with these instructions
may result in electrical hazards.
•Wear gloves to protect against sharp edges.
• The manufacturer is not liable for any damage caused by not following these instructions.
1. Preparing for installation:
Before installing your rangehood:
• Please read the instructions carefully.
• Unpack the rangehood.
• Ensure the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and frequency of
the installation site.
• Check all functions are working.
• Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes etc.
• The rangehood surfaces can be damaged during installation if grazed or knocked by tools. Please take care to
protect the surfaces during installation.
• Protect the cooktop surface with cardboard, or the like, to prevent damage occurring whilst the rangehood is
being installed above.
• Temporarily mark the height of the bottom of the rangehood and the centre of the cooktop on the wall according
to the information given in the ‘Installation instructions – Height of rangehood’ section.
• The wall used for mounting the rangehood should have sufficient strength and a flat surface.
2. Attach chimney brackets and rangehood
mounting screws to the wall
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
7

• Attach the chimney bracket and upper chimney
bracket (if using the upper chimney) in the
locations shown in Fig. 2 and 3. Use the 30 mm
screws (and expansion plugs if attaching to
masonry).
• Attach the upper rangehood mounting screws in
the locations shown in Fig. 2 and 3. Using the 30
mm screws (and expansion plugs if attaching to
masonry). Ensure that there is a 2 mm gap
between the screw head and the wall (see Fig
1).
Product Dimensions mm
N. Lower rangehood attachment point width 508
O. Lower rangehood attachment point height 44
P. Upper rangehood attachment point width 250
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
8

Product Dimensions mm
Q. Upper rangehood attachment point height 291
R. Chimney bracket attachment point width 235
S. Chimney bracket attachment point height 615
T. Upper chimney bracket attachment point width 250
U. Upper chimney bracket attachment point height 25
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
9

3. Attach the ducting adapter to the rangehood
• Place the ducting adapter onto the rangehood
and screw it in place using 10 mm screws.
4. Wall mounting
• Remove the filters – pull the relative catch and tilt the filter downwards until it disengages from the supports.
• Hang the rangehood off the upper rangehood mounting screws with 2 mm gap. Hang off the keyhole attachment
points on the back of the rangehood then tighten the screws.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC60PHTX1/User_Guide_HC60PHTX1/03_Installation_i…
Updated: Fri, 03 Apr 2020 01:59:14 GMT
Powered by
10