Fisher & Paykel HC60PLX4 User manual

Installation instructions
lease read and follow the ‘Safety and warnings’ and ‘installation instructions’ sections carefully before using your
rangehood.
Rangehood (1) Installation instructions User guide
manual (1) Chimney (1)
Upper chimney (1)
Upper chimney bracket (1) Chimney bracket (1)
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
1

150 mm diameter ducting adapter (1)
125 mm diameter ducting adapter (1)
Expansion plug (8)
30 mm self tapping screw (4)
10 mm self tapping screw (4)
roduct dimensions
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
2

Product dimensions for HC90PLX4 and HC90PLX4
Property (mm) HC60PLX4 HC90PLX4
A. Overall height of product
min. 610 – max.
1050
min. 610 – max.
1050
B. Overall width of product 598 898
C. Overall depth of product 500 500
D. Height of product 80 80
E. Width of chimney 320 320
F. Depth of chimney 290 290
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
3

Property (mm) HC60PLX4 HC90PLX4
G. Distance from centre of ducting outlet to back of
product 80 80
H. Distance from centre of ducting outlet to side of
chimney 160 160
I. Diameter of ducting outlet 150 150
J. Distance between centre of lights 235 370
K. Distance between centre of lights to back of product 50 50
Length of power cord 1400 1400
Actual product dimensions may vary by ± 2 mm.
lease read the entire instructions before installing the rangehood.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
4

Height of rangehood
Installation Dimensions
Property Size (mm)
L. Installation height min. 650 – max. 1050 min.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
5

Property Size (mm)
•Ducted
•Recirculation 690 – max. 1050
M. Height top of cooktop to base of product
•Electric cooktop
•Gas cooktop
min. 600 – max. 750
min. 650 – max. 750
Rangehood installation height above the cooktop is the user’s preference. Lower
installation heights will improve the efficiency of capturing cooking odours, grease, and
smoke. This rangehood must be installed between the minimum and maximum dimensions
indicated in the table above.
Venting options
Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air are
fulfilled.
The rangehood can be installed to operate with the exhaust air ducted externally from the kitchen, or installed to
operate with the exhaust air recirculating within the kitchen.
Ducted
For ducted installation it is recommended that 150 mm diameter, rigid or semi-rigid ducting is used. This will
require a 160 mm (min) round hole in the ceiling or wall. Care should be taken to position the hole correctly.
For optimal efficiency use the shortest and straightest duct route possible and use rigid or semi-rigid ducting for
reduced noise and increased airflow. Flexible metal ducting should only be used as a last resort (ie in difficult
installations) and if used ensure that it is straight and smooth and extended as much as possible.
Recirculating
To enable the product to operate with the air recirculating, please purchase a recirculation diverter and carbon
filters (refer to the ‘ arts and accessories’ section). The recirculation diverter is required to channel the air out the
side vents at the top of the chimney and the carbon filters are required to remove odours.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
6

A ducting hole is not required in the wall or ceiling if the rangehood is installed to operate
with exhaust air recirculating.
•This product is heavy and requires two persons for installation.
•Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards.
•Failure to install the screws or fixing device in accordance with these instructions may
result in electrical hazards
Wear gloves to protect against sharp edges.
The manufacturer is not liable for any damage caused by not following these instructions.
Installation
1. Preparing for installation:
Before installing your rangehood:
• lease read the instructions carefully.
• Unpack the rangehood.
• Ensure that the voltage (V) and the frequency (Hz) indicated on the serial plate match the voltage and
frequency at the installation site.
• Check that all functions are working.
• Check that the area behind the installation surface to be drilled is clear of any electrical cables or pipes, etc.
• The rangehood surfaces can be damaged during installation if grazed or knocked by tools. lease take care to
protect the surfaces during installation.
• rotect the cooktop surface with cardboard, or the like, to prevent damage occurring whilst the rangehood is
being installed above.
• Temporarily mark the height of the bottom of the rangehood and the centre of the cooktop on the wall according
to the information given in the ‘Installation instructions
◦ Height of rangehood’ section.
• The wall used for mounting the rangehood should have sufficient strength and a flat surface.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
7

2. Attach chimney brackets and rangehood
mounting screws to the wall
• Attach the chimney bracket and upper chimney
bracket in the location shown in Fig. 2 and Fig. 3. Use
the 30 mm screws (and expansion plugs if attaching to
masonry).
• Attach the upper rangehood mounting screws in the
locations shown in Fig. 2 and Fig. 3. Use the 30 mm
screws (and expansion plugs if attaching to masonry).
Ensure that there is a 2 mm gap between the screw
head and the wall (see Fig. 1). Fig. 1
Fig. 2
Product dimensions for HC90PLX4 and HC90PLX4 (Continued)
Property (mm) HC60PLX4 HC90PLX4
N. Lower rangehood attachment point width 440 550
O. Lower rangehood attachment point height 40 40
P. Upper rangehood attachment point width 250 250
Q. Upper rangehood attachment point height 295 295
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
8

Property (mm) HC60PLX4 HC90PLX4
R. Chimney bracket attachment point width 235 235
S. Chimney bracket attachment point height 575 575
T. Upper chimney bracket attachment point width 250 250
U. Upper chimney bracket attachment point height 25 25
3. Attach the ducting adapter to the rangehood
• lace the ducting adapter onto the rangehood and
screw it in place using the 10 mm screws.
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
9

4. Wall mounting
• Remove the filters – pull the relative catch and tilt the filter downwards until it disengages from the supports.
• Hang the rangehood off the upper rangehood mounting screws with 2 mm gap. Hang off the keyhole attachment
points on the back of the rangehood then tighten the screws.
• Attach the lower rangehood mounting screws to fix the rangehood to the wall.
• Refit the filters.
5. Attach ducting
• Attach ducting to the ducting adapter using aluminium duct tape and vent outside.
6. Attach chimney
• Bend the tabs on the chimney (A).
• lace chimney around the hood chassis and hang off the bracket (B).
https://producthelp.fisherpaykel.com/au/Cook/Rangehoods/Canopy/HC90 LX4/User_Guide_HC90 LX4/02_Installation_instr…
Updated: Thu, 30 Jul 2020 10:51:38 GMT
owered by
10