Fisher & Paykel HS60 User manual

111024 Issue C
ECN: 07 039
STEP 2. PREPARING THE RANGEHOOD
FOR INSTALLATION
If the rangehood is to be installed
as a ducted hood, remove the
appropriate duct knockout.
See Diagram 1.
Refer to Steps 3 & 4 for MOUNTING
METHODS and ALTERNATIVE DUCTING
METHODS.
If the rangehood is to be installed as a
recirculating hood, first ensure the
overhead cabinets are built according
to Diagram 2, and
i) Remove Cover Tape ‘A’. See Diagram 1
ii) if 80mm handle is not installed. Remove
Front Fascia ‘B’ by undoing 3 screws on
the fascia. See Diagram 1.
iii) Replace ‘B’ with Replacement Front Panel ‘C’
constructed of same or similar material as
cupboard doors. See diagram 2 for height of panel.
iv) Now install the rangehood in accordance with step 3.
The rangehood’s plug can be easily plugged into the nearest wall socket, or if connected
directly into the house wiring a registered electrician is required.
DIAGRAM 2
80
DIAGRAM 3
STEP 3. MOUNTING THE RANGEHOOD
The Rangehood can be mounted in two ways, top
or sides.
TOP MOUNTING
Fix rangehood to a shelf mounted
at the right height in your wall
units, by drilling 4 holes (see
Diagram 3) and fixing with 4
screws supplied. The position of
the holes can quickly be found
using the installation sheet
provided.
SIDE MOUNTING
See installation sheet provided.
DIAGRAM 1
C
AB
KNOCKOUTS
For top ducting cut hole to suit duct size
Dimensions shown are for UNIDUCT
WALL
INSTALLATION INSTRUCTION
SLIDEOUT RANGEHOOD
Note: Generic model is shown.
Actual product may differ.
All dimensions are in millimeters
PRODUCT DIMENSIONS
INSTALLATION OF UNIT
Please read the entire instructions
before installing the rangehood.
The following steps will help you to easily install your rangehood
in the manner most suited to your kitchen. Please read the
complete instructions before installing your rangehood. Plan your
ducting method and mounting arrangements, choose your electrical
connection, then simply follow these instructions.
When installing the rangehood, the lower edge of the unit must
be a minimum of 600mm (650mm for gas cooker)
above the cooking range.
The recommended position for the hood is 650mm above
the hotplates.
STEP 1. PRELIMINARY
INSTRUCTIONS
597 (600 Model)
897 (900 Model)
161
462
280
33 or 80
POWER CORD EXITS
THIS SIDE EITHER
TOP OR BOTTOM
not less
than 650 mm
GAS
BURNER

WARNING
•This appliance is not intended for use by young children or infirm
persons without supervision.
•Young children should be supervised to ensure that they do not
play with the appliance.
•There shall be adequate ventilation of the room when the
rangehood is used at the same time as appliances burning gas
or other fuels.
•You must read the details concerning the method and frequency
of cleaning. (Refer to Maintenance Instruction)
•There is a fire risk if cleaning is not carried out in accordance
with the instructions. (Refer to Maintenance Instruction)
•Do not flambé under the rangehood.
•Exhaust air must not be discharged into an existing flue which
is used for exhausting fumes from appliances burning gas or
other fuels.
•The minimum distance between the hob surface and the lowest
part of the range hood is 600mm. This distance shall be at least
650mm if the range hood is installed over a gas hob.
•Attention should be given to ensure that any applicable
regulations concerning the discharge of exhaust air are fulfilled.
•If the supply cord of this equipment is damaged, it must only
be replaced by the manufacturer or its service agent or similarly
qualified person in order to avoid a hazard.
IMPORTANT:
THESE RANGEHOODS ARE NOT SUITABLE
FOR BARBEQUES, OPEN ROTISSERIES,
OR IN A COMMERCIAL APPLICATION
MAINTENANCE
USE & CARE GUIDE
Thank you for choosing our product. These instructions will help you derive the greatest
benefit from it. Please remember to fill out the details on the warranty certificate.
LIGHT
The light is controlled by an ON/OFF switch in accordance with the graphics printed on
the control panel.
FAN
The fan is controlled by a switch in accordance with the graphics printed on the control
panel.
When installing or replacing filters, remove protective plastic covering
from the filters.
FILTER MAINTENANCE
Filter can be removed by pulling the tray open and sliding the
filter forward. To maintain efficiency the filter should be removed
regularly (approximately monthly), and washed using soap or
mild detergents or dishwasher powders. Badly smoked filters
may be cleaned with “cookware cleaners”.
Rangehoods fitted with Charcoal Filters are designed to remove
grease and odours from cooking vapours, prior to the cleansed
air re-entering the kitchen (when the Rangehood is in recirculating
mode). Charcoal Filters should be replaced every three to six months
depending on use.
REPLACEMENT OF HALOGEN LAMPS
To replace a lamp, first disconnect rangehood from power
supply. Apply finger pressure to the face of the lamp and twist
one quarter turn anti-clockwise, the lamp will now be free to drop out.
Insert the replacement lamp into the lamp holder, apply finger
pressure and twist one quarter turn clockwise.
GENERAL MAINTENANCE
The rangehood should be cleaned regularly using warm
water with soap or mild liquid detergents, so that no build-up
of grease occurs as these deposits are corrosive. Do not
use abrasives or harsh detergents/cleaning fluids.
STEP 4. ALTERNATIVE DUCTING METHODS
Some authorities require rangehoods to be vented outside. DUCTED models comply with
this requirement in every respect.
DUCTING OPTIONS
SIDE DUCTING
TOP DUCTING THROUGH ROOF REAR DUCTED
RECOMMENDED UNIDUCT DUCTING
SYSTEMS FOR RANGEHOODS
Note: Fully saturated charcoal filters can become a barrier to air
movement therefore impeding Rangehood performance.
In the event of fire, fully grease laden filters could be flammable
and therefore regular replacement is recommended.
In ducted installations, conventional aluminium filters are
recommended 111024 Issue C
ECN: 07 039
Electrical Rating:
Models: 80417/18/19/20/21/22/23
210W (0.84A)
Models: 80462/63/64/65
162W (0.68A)
Max at 230 - 240V 50Hz

Align left hand front corner Align right hand front corner
Align with inside left cupboard wall Align with inside right cupboard wall
Align cupboard door front

Installation sheet
Top Mounting (Preferred installation method)
1. Use template provided on the reverse page.
2. Cut or fold along the dotted edge.
3. Align template with the inside cupboard wall and the front of the cupboard door and drill holes.
Keep opposite side door to which you are drilling closed in order to align template correctly.
4. Screw down through shelf into plastic lugs in slideout.
Position
f
r
o
n
t
left
hand corner
Position
f
r
o
n
t
right
hand corner
Position
f
r
o
n
t
left
hand corner
Position
f
r
o
n
t
right
hand corner
Align cupboard door front
Align with inside left cupboard wall Align with inside right cupboard wall
Align cupboard door front
Align with inside left cupboard wall Align with inside right cupboard wall
Cupboard wall
Cupboard door
Side Mounting
1. Remove filter.
2. Remove thin plastic skin (A) from each side fixing hole (see diagrams below).
Robinhood recommends an 8mm diameter drill be used.
3. Position slideout (ensuring unit is level) and fix in place using screws and hollow dowels
through each side fixing hole (see diagrams below).
Slideout Side
Hollow Dowel
Cupboard
(A)
IMPORTANT ***To correctly align the front rail of the slideout flush with the cabinets.
Keep the opposite side door, to which you are drilling, closed. See diagram below***
111052 Iss A
ECN: 07 039