Fisher & Paykel HC24DTXB2 User manual

6
INSTALLATION INSTRUCTIONS
Contents of packaging
Upper chimney bracket
(1)
Installation instructions
User guide manual
(1)
Chimney
(1)
6” (152mm) diameter
Ducting adapter with
back draft damper
(1)
1⁄” (30mm)
Expansion plug
(10)
Upper chimney
(1)
Ventilation hood
(1)
Power connection box
(1)
Chimney bracket
(1)
US CA
INSTALLATION INSTRUCTIONS
USER GUIDE
INSTRUCTIONS D’INSTALLATION
GUIDE D’UTILISATION
HC24DTXB2, HC30DTXB2, and HC36DTXB2 models
Modèles HC24DTXB2, HC30DTXB2 et HC36DTXB2
Chimney Box Ventilation Hood
Hotte de Ventilation Murale Décorative

7
INSTALLATION INSTRUCTIONS
1⁄” (30mm)
Self tapping screw
(10)
⅜” (10mm)
Self tapping screw
(4)
1¾” (44mm)
Drywall expansion plug
(8)
⅜” (10mm)
Screw
(2)
EN

8
INSTALLATION INSTRUCTIONS
Please read the entire instructions before installing the ventilation hood.
Product dimensions
h
i
C
j
g f
A
A
B
D E
Ø
l
k
UL power
connection box
min
max

9
INSTALLATION INSTRUCTIONS
HC24DTXB2 HC30DTXB2 HC36DTXB2
PRODUCT DIMENSIONS inches (mm) inches (mm) inches (mm)
AMin overall height of product 23¾” (603) 23¾” (603) 23¾” (603)
AMax overall height of product 41⁄” (1043) 41⁄” (1043) 41⁄” (1043)
BOverall width of product 23⁄” (598) 29¾” (755) 35⅜” (898)
COverall depth of product 19⁄” (500) 19⁄” (500) 19⁄” (500)
DHeight of product 2⁄” (65) 2⁄” (65) 2⁄” (65)
EHeight of stainless steel face panel 1⁄” (36) 1⁄” (36) 1⁄” (36)
FWidth of chimney 12⅝” (320) 12⅝” (320) 12⅝” (320)
GDepth of chimney 11⁄” (290) 11⁄” (290) 11⁄” (290)
HDistance from center of ducting
outlet to back of product 3⅜” (85) 3⅜” (85) 3⅜” (85)
IDistance from center of ducting
outlet to side of chimney 6⁄” (160) 6⁄” (160) 6⁄” (160)
JDiameter of ducting outlet 6” (152) 6” (152) 6” (152)
KDistance between center of lights 9⅝” (244) 9⅝” (244) 9⅝” (244)
LDistance between center of lights
and back of product 1⅜” (35) 1⅜” (35) 1⅜” (35)
IMPORTANT!
Actual product dimensions may vary by ± ⁄”(2 mm).
EN

10
INSTALLATION INSTRUCTIONS
Height of ventilation hood
INSTALLATION DIMENSIONS inches (mm)
MInstallation height
Ducted
Recirculation
min. 24⁄” (627) – max. 43⁄” (1034)
min. 26⅞” (682) – max. 43⁄” (1034)
NHeight top of cooking
surface to base of product
min. 26” (660) – max. recommended 36” (915)
This ventilation hood must be installed no lower than the minimum height indicated
in the table above. Minimum installation height may be greater if required by the
cooktop manufacturer or safety and warning section of this user guide. Installation
at the minimum height will improve the efficiency of capturing cooking odors, grease
and smoke. Installation at the maximum height improves user ergonomics by offering
increased head room.
M
N

11
INSTALLATION INSTRUCTIONS
WARNING!
To reduce the risk of fire, use only metal ductwork. Do not use flexible plastic ducting
CAUTION!
To reduce risk of fire and to properly exhaust air, be sure to duct air outside – do not
vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or
garages.
Venting options
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
The ventilation hood can be installed to operate with the exhaust air ducted
externally from the kitchen, or installed to operate with the exhaust air recirculating
within the kitchen.
Ducted
For ducted installation it is recommended that 6” (152 mm) diameter, rigid or semi-rigid
ducting is used. This will require a 6⁄” (160 mm) (min) round hole in the ceiling or wall.
Care should be taken to position the hole correctly.
For optimal efficiency use the shortest and straightest duct route possible and use rigid
or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting
should only be used as a last resort (ie in difficult installations) and if used ensure that it
is straight and smooth and extended as much as possible.
Recirculating
To enable the product to operate with the air recirculating, please purchase a
recirculation diverter and carbon filters or recirculation kit (refer to the ‘Parts and
accessories’ section). This recirculation diverter is required to channel the air out the
side vents at the top of the chimney and the carbon filters are required to remove odors.
Note: a ducting hole is not required in the wall or ceiling if the ventilation hood is
installed to operate with exhaust air recirculating.
EN

12
INSTALLATION INSTRUCTIONS
WARNING!
 This product is heavy and requires two persons for installation.
 Installation work and electrical wiring must be done by qualified person(s)
in accordance with all applicable codes and standards.
IMPORTANT!
Wear gloves to protect against sharp edges.
The manufacturer is not liable for any damage caused by not following these instructions.
Installation
1Preparing for installation:
Before installing your ventilation hood:
 Please read the instructions carefully.
 Unpack the ventilation hood.
 Ensure the voltage (V) and the frequency (Hz) indicated on the serial plate match
the voltage and frequency of the installation site.
 Check that the area behind the installation surface to be drilled is clear of any
electrical cables or pipes etc
 The ventilation hood surfaces can be damaged during installation if grazed or
knocked by tools. Please take care to protect the surfaces during installation.
 Protect the cooktop surface with cardboard, or the like, to prevent damage
occurring whilst the ventilation hood is being installed above.
 Temporarily mark the height of the bottom of the ventilation hood and the center
of the cooktop on the wall according to the information given in the ‘Installation
instructions – Height of ventilation hood’ section.
 The wall used for mounting the ventilation hood should have sufficient strength
and a flat surface.
2Attach chimney brackets and ventilation hood mounting screws to the wall
 Attach the chimney bracket and upper
chimney bracket (if using the upper chimney)
in the locations shown in Fig.2 (refer to
page13) and Fig.3 (refer to page 14). Use the
1⁄” (30 mm) screws (and expansion plugs if
attaching to masonry).
 Attach the upper ventilation hood mounting
screws in the locations shown in Fig.2 (refer to
page 13) and Fig.3 (refer to page 14). Using the
1⁄” (30 mm) screws (and expansion plugs if
attaching to masonry). Ensure that there is a
⁄” (2 mm) gap between the screw head and
the wall (Fig.1).
Fig.1
⁄” (2mm)

13
INSTALLATION INSTRUCTIONS
PRODUCT DIMENSIONS inches (mm)
oLower ventilation hood attachment point width 20” (508)
PLower ventilation hood attachment point height 1⁄” (43)
qUpper ventilation hood attachment point width 9⅞” (250)
rUpper ventilation hood attachment point height 11⁄” (288)
sChimney bracket attachment point width 9¼” (235)
tChimney bracket attachment point height 22¼” (566)
uUpper chimney bracket attachment point width 9⅞” (250)
vUpper chimney bracket attachment point height 1” (25)
Fig.2
Upper chimney bracket
attachment points
Chimney bracket
attachment points
Upper ventilation
hood attachment point
Lower ventilation
hood attachment point
u
o
v
t
r
p
q
s
EN

14
INSTALLATION INSTRUCTIONS
Fig.3
3Attach ducting adapter and power connection box
to the ventilation hood
 Place the ducting adapter onto the ventilation hood and
screw it in place using ⅜” (10mm) screws.
 Place the power connection box onto the ventilation hood
and screw it in place using ⅜” (10mm) screws.
 Follow wiring instructions described in the ‘Electrical
connection’ section page16.

15
INSTALLATION INSTRUCTIONS
4Wall mounting
 Remove the filters – pull the relative catch and tilt the filter downwards until
it disengages from the supports.
 Hang the ventilation hood off the upper ventilation hood mounting screws
with ⁄” (2 mm) gap. Hang off the keyhole attachment points on the back
of the ventilation hood then tighten the screws.
 Attach the lower ventilation hood mounting screws to fix the ventilation hood
to the wall.
 Refit the filters.
EN