Fisher-Price T4265 User manual

www.fisher-price.com
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “D” (LR20) alkaline batteries for mobile
operation and two "AAA" (LR03) alkaline batteries for
remote operation (batteries not included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
T4265

2
WARNING
Consumer Information
Prevent Entanglement Injury
• Keep mobile out of baby’s reach.
• Remove mobile portion of product from crib or playpen
when baby begins to push up on hands and knees.
• This product may not attach to all crib designs. Do not add
additional strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib or playpen.
In exceptional circumstances, batteries may leak fluids that can cause a chemical
burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove exhausted batteries
from the product. Dispose of batteries safely. Do not dispose of product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
•
If removable, rechargeable batteries are used, they are only to be charged under adult supervision.
Battery Safety Information
IMPORTANT! Always attach with all provided fasteners tightly to a crib or playpen according to the
instructions. Do not add additional strings or straps to attach to a crib. Check frequently.
• The mobile portion of this product may be used from birth until 5 months.
• The base portion of this product may be used from birth until 36 months.
• A crib mobile is intended for visual stimulation and is not to be grasped by a child.
• Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not
immerse this toy. The soft toys are surface washable.
• This toy has no consumer serviceable parts. Do not take this toy apart.
• If this product begins to operate erratically, you may need to reset the electronics.
Slide the power/volume switch on the mobile base off and then back on. Remove the
batteries from the remote and replace them.
• Protect the environment by not disposing of this product with household waste
(2002/96/EC). Check your local authority for recycling advice and facilities
(Europe only).

3
Parts
Arm
Note: All of the screws used to assemble this toy are attached to the product.
Follow these instructions carefully to fully secure the screws. Tighten and loosen all
screws with a Phillips screwdriver. Do not over-tighten the screws.
BaseCrib Connector
Mobile Hub
3 Long Spokes
3 Short Spokes
Remote

4
Remote
• Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove
the battery compartment door.
• Insert two "AAA" (LR03) alkaline batteries.
• Replace the battery compartment door and tighten the screw.
1,5V x 3
“D” (LR20)
Mobile Base
• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove
the battery compartment door.
• Insert three “D” (LR20) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
IMPORTANT! Under normal use conditions, the batteries in the mobile base will require
replacement more often than the batteries in the remote. When sounds or lights become
faint or stop, it’s time for an adult to change the batteries.
Battery Installation
1,5V x 2
"AAA" (LR03)
Hint: We recommend using alkaline batteries for longer battery life.

5
1
2
• Fit the crib connector to the base and tighten both screws.
IMPORTANT! Make sure the straps are over the top of the crib connector.
Crib Connector
Base
• First, press the button on the mobile base, next to the
socket Aand then slide the socket door open B.
• Fit the arm into the socket in the base and tighten
both screws.
Arm
Socket
1
1
A
PRESS
SLIDE
SLIDE
B
Assembly

6
Assembly
• Attach a long spoke to the mobile hub, as shown.
• Tighten the screw in the long spoke.
• Repeat this procedure to attach the remaining long spokes to the mobile hub.
• Fit the end of the arm to the socket on the mobile hub.
• Tighten both screws in the arm to secure the mobile hub.
Arm
Socket
Long Spoke
1
3
1
4

7
Assembly
• Attach a short spoke to the mobile hub, as shown.
• Tighten the screw in the short spoke.
• Repeat this procedure to attach the remaining short spokes to the mobile hub.
Short Spoke
1
5

8
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. T4265pr-0920
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA
FCC Statement (United States Only)
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced
radio/TV technician for help.
Note: Changes or modifications not
expressly approved by the manufacturer
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
ICES-003
This Class B digital apparatus complies with
Canadian ICES-003.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
NMB-003
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée
seulement aux conditions suivantes:
(1) il ne doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit être prêt
à accepter tout brouillage radioélectrique
reçu, même si ce brouillage est susceptible
de compromettre le fonctionnement
du dispositif.
Consumer Information
CO
N
S
UMER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.

9
Crib Attachment
• Position the base so that the decorated side faces the inside of the crib.
• Fit the base onto the crib top rail.
Hint: The base is designed to fit most crib designs. Please refer to the main illustration
and the inset photograph.
• Make sure the top strap is hanging over the crib top rail. Pull the bottom strap through
the crib rails.
• Buckle the straps. Make sure you hear a “click”.
IMPORTANT! If you are attaching this toy to a crib side rail that can be lowered and raised,
make sure the crib side rail is in the raised (locked) position whenever a child is in the crib.
Crib Top Rail
Base
Buckles
Buckles
1
1
WARNING
Prevent Entanglement Injury
• Keep mobile out of baby’s reach.
• Remove mobile portion of product from crib or playpen
when baby begins to push up on hands and knees.
• This product may not attach to all crib designs. Do not add
additional strings or straps to attach to crib or playpen.
• Use ONLY attached to a crib or playpen.

10
Crib Attachment
• Make sure the straps are tightened securely around the crib rail.
• While pushing the tab at the bottom of the buckle, pull the free end of the strap to
tighten on the rail.
Hint: You can secure the free end of the strap to the base.
1
2