FitLogic MIRACLE R270 User manual

0
Read all the instructions carefully before
assembling and using this product. Retain this
owner’s manual for the future’s reference.
!

1
1. Plug the power cord of the treadmill directly into a dedicated grounded circuit. This
product must be grounded well. If it has breakdown, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock.
2. Position the treadmill on a clean and flat surface with at least 2m*1m area. Do not
place the treadmill on thick carpet as it may interfere with proper ventilation. Also, do
not place the treadmill near water or outdoors.
3. Position the treadmill where the wall plug is visible and accessible.
4. NEVER start the treadmill while you are standing on the walking belt. After turning
the power on and adjusting the speed control, there may be a pause before the
walking belt begins to move, ALWAYS stand on the foot rails on the sides of the
frame until the belt is moving.
5. Wear appropriate clothing when exercising on the treadmill. Do not wear long,
loose fitting clothing that could become caught in the treadmill. Always wear running
or aerobic shoes with rubber soles.
6. Always unplug the power cord before removing the treadmill motor cover.
7. Keep small children away from the treadmill during operation.
8. Always hold the handrails when initially walking or running on the treadmill, until
you are comfortable with the use of the treadmill.
9. Always attach the safety pull pin rope to your clothing when using the treadmill. If
the treadmill should suddenly increase in speed due to an electronics failure or the
speed being inadvertently increased, the treadmill will come to a sudden stop when
the pull pin is disengaged from the console.
IMPORTANT SAFETY PRECAUTIONS

2
10. When the treadmill is not being used, the power cord should be unplugged and
the safety pull pin should be removed.
11. Before starting any exercise program, consult with your physician or health
professional. He or she can help to establish the exercise frequency, intensity (target
heart zone) and time appropriate to your particular age and physical condition. If you
have any pain or tightness in your chest, an irregular heartbeat, shortness of breath,
feel faint or have any discomfort while you exercise, STOP IMMEDIATELY! Consult
your physician before continuing.
12. If you observe any damage or wear on the mains plug or on any section of the
mains lead then please have these replaced immediately by a qualified electrician –
do not attempt to change or repair these yourself.
13. If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
14. Put your feet on the side rail before using the treadmill, and always attach the
safety pull pin rope to your clothing. Hold the handle bar before the running belt
moving well ( feel the running speed by your single foot before using it). To avoid loss
balance, please slow down the speed to the lowest or take off the safety. And hold the
handle bar to jump to the side rail when emergency or the safety key is not attached.
IMPORTANT SAFETY PRECAUTIONS

3
When you open the carton, you will find the below spare parts:
Spare parts list:
NO.
DESCRIPTION
SPEC
QTY
NO.
DESCRIPTION
SPEC
QTY
1
CONSOLE MAIN FRAME
1
31
Right Bottom
Decoration Case
1
9
LEFT HANDLE BAR
1
86
BOLT
M8*16
8
10
RIGHT HANDLE BAR
1
90
BOLT
M8*35
2
16
Allen Wrench With Driver
S=13, 14,
15
1
92
BOLT
M8*42
2
17
5# ALLEN WRENCH
5 mm
1
104
BOLT
M6*12
6
23
LEFT OUTTER COVER
1
107
SCREW
ST4.2*12
10
26
RIGHT OUTTER COVER
1
108
SCREW
ST4.2*13
8
30
Left Bottom Decoration
Case
1
122
4# ALLEN WRENCH
4 mm
1
Assembly tools：
Allen Wrench: 5mm 1pc, 4mm 1pc
Allen Wrench With Screw Driver :S=13、14、15 1pc
ASSEMBLY INSTRUCTIONS

4
Notice: Do not turn power on before assembly is done.
Step 1：
Step 2:
Step 3:
Open the carton，take out the
spare parts，and put the MAIN
FRAME on the ground.
Turn the computer and the
upright frame up .
Attention: Don’t press the
wires inside the upright
frame when folding. Hold
the computer and upright
frame to avoid dropping.
Use 5# Allen wrench, lock the
left & right upright tubes (#3 &
#4) onto the base main frame
with M8*16 bolt (#86), and arc
washer (#115).
Attention: Hold the left and
right upright tubes to avoid
dropping.
ASSEMBLY STEPS

5
Step 4：
Step 5：
Step 6：
Connect the hand pulse wire.
Use 4# Allen wrench, lock the
left and right handle bar
(#9,#10) onto the upright
upper post (#3,#4) by M6*12
bolt (#104).
Use 5# Allen wrench, turn the
computer to the right position
according to the arrow direction
shown as the picture. Lock the
console main frame (#1) onto
the upright upper frame by
M8*35 bolt (#90) and nut. And
then lock the bolt on the position
“A”.
Use Allen wrench with screw
driver, lock the left & right outer
cover (#23,#26) onto the upright
upper frame (#3,#4) by screw
4.2*13 (#108).
Attention: Please fix the treadmill well according to the above steps, and then go to
the next step to assemble the plastic covers.

6
Step 7:
1. Put the left and right bottom
decoration case (#30,#31) onto the
base main frame (#5), then lock them
with ST4.2*12 screw (#107) by Allen
wrench with screw driver.
Attention: Please don’t put the power on until you make sure that all the above
steps are finished and all the bolts are tightened well. Please also read all the
following instructions when you operate the treadmill.

7
Folding up:
Releasing down:
FOLDING INSTRUCTION
Hold the place A, and pull up
the main frame up as the arrow
direction till you hear the sound
of the cylinder (#15).
Hold the place A, and pull up
the main frame as shown of the
arrow till you hear the sound
from the cylinder (15).

8
TECHNICAL PARAMETER
BUILT UP
SIZE(mm)
1760*775*1350mm
FOLDABLE
SIZE(mm)
830*775*1620mm
RUNNING
BOARD(mm)
460*1320mm
NET WEIGHT
69KG
MAX USE’S
WEIGHT
120KG
SPEED
RANGE
1.0-20KM/h
INCLINE
LEVEL
0-15%
ONE LCD
DISPLAY
WINDOW
SPEED,TIME,DISTANCE,CALORIES,PULSE INCLINE

9
GROUND GUIDE
This product must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This product is
equipped with a cord having an equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
DANGER –Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product
–if it will not fit the outlet, have a proper outlet installed by a qualified electrician. This product
is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug
illustrated in sketch A in following figure. Make that the product is connected to an outlet
having the same configuration as the plug. No adapter should be used with this product.

10
WINDOW DISPLAY:
1. “SPEED” window: On operation state, it will display the current speed, and the
speed range is 1.0-20KM/H(Kilometer) or 0.6-12MPH(Mile).
2. “INCL” window: Display the current incline level and the range is 0--15%.
3. “TIME”: Display the running exercise time. Counting from 0:00 to 99:59, when
it reaches 99:59, the speed of the treadmill will be slowly decreased. After the
treadmill stops completely, the unit will become STANDBY status after 5 seconds.
Counting from the target data down to 0:00, when it reaches 0:00, the speed of
the treadmill will also be slowly decreased. After the treadmill stops completely,
the unit will become STANDBY state.
4. “DIST.” Window: Display the exercise distance. Counting from 0:00 to 99:9,
when it is over 99:9, the display will be reset to be 0:00 and the counting will start
again from 0:00 to 99:9. Counting from the target distance down to 0:00, when it
reaches 0:00, the speed of the treadmill will also be slowly decreased. After the
treadmill stops completely, the unit will become STANDBY state.
OPERATION GUIDE

11
5.“CAL /PULSE” window : Display the runner’s pulse and calories data. Counting
from 0 to 999, when it is over 999, the display will be reset to be 0 and the
counting will start again from 0 to 999. Counting from the target data down to 0,
when it reaches 0, the speed of the treadmill will also be slowly decreased. After
the treadmill stops completely, the unit will become STANDBY state. When the
runner grasps the hand pulse, it will test pulse after 5 seconds and show the data
in window, the relevant light will show at the same time, pulse range is 50 to 200
hypo/min ( the data is just for reference, can not be used as medical data).
BUTTON FUNCTION:
1. “PROG.” Button: Under the STANDBY state, press “PROG.” button, you can
circularly choose either “0:00” or the following 19 operation modes of
“P1-P2-P3-P4-P5-P6-P7-P8-P9-P10-P11-P12-P13-P14-P15-U1-U2-U3-FAT” FAT
are the body fat testing function). Manual mode is the default mode with speed 1.0
KM/H. (0:00 is manual model, P1-P15 is preset program and U1-U3 is the user’s
self-set program).
2. “MODE” Button: Press this button to choose the modes: “0:00”, “15:00”, “1.0”
and “50” (“0:00” is manual mode, “15:00” is the time count-down mode, “1.0” is
the distance count-down mode and “50” is the calorie count-down mode). When
you choose each mode, you can press the speed button and incline button to set
the target count-down data, after that, press the START button to start the
treadmill.
3.“START” button：When the power is on and the safety key is attached onto the
console, press this button at any time, it can start the treadmill.
4. “STOP” button: While running the treadmill, press this button at any time to
stop the treadmill and return all the data back to 0.
5. “SPEED+”,“SPEED-” Button: After starting the treadmill, press “SPEED” button
to adjust the speed and the adjustment range of speed is 0.1km each time. When
pressing “SPEED” button for more than 0.5 seconds, the speed will be
continuously increased or decreased.
6. “INC+”, “INC-” Button: After starting the treadmill, pressing “INCLINE” button
can adjust the level of incline and the adjustment range of speed is 1 section each

12
time. When pressing “INCLINE” button for more than 0.5 seconds, the incline level
will be continuously increased or decreased.
7.“SPEED: 3, 5, 7, 9, 11”quick access button: you can do quick setting of the
speed.
8. “INCLINE: 3, 5,7, 9, 11” quick access button: you can do quick setting of the
speed.
9. When the treadmill is under standby state, press both SPEED+ and INCLINE+
for about 3 seconds. You will hear the buzzer make a sound “BI”, then the changes
between Kilometer and Mile will be finished.
START-UP QUICKLY (MANUAL)
1. Put the power switch on, and then attach the safety key to the computer.
2. Press START/STOP button，the system will enter into 3 seconds count-down,
the buzzer will make the sound “Bi” and the TIME window will start to count down,
then the speed will run 1.0km/hour after 3 seconds.
3. After start-up, you can use speed up or down to adjust the speed up or down.
The operation of exercise process:
1. Press “SPEED+” will increase the running speed.
2. Press “SPEED-“ will decrease the running speed.
3. Press “INCLINE+” will increase the incline level.
4. Press “INCINE-“ will decrease the incline level.
5. Press STOP will reduce the speed until the unit stops.
6. When the user hold the hand pulse about 5 seconds, it will display pulse data.

13
MANUAL MODE:
1. When the treadmill is under the standby state, press START button, the
treadmill will start to run from the speed 1.0km/h and the inline of “0” level. The
other windows will also start to count up from “0”, press “INCLINE+”,”INCLINE-”,
“SPEED+”, “SPEED-” to change the incline and speed.
2. Set up the TIME, press “MODE” button to enter into time count-down, the TIME
window will display “15:00” and glitter. Press “INCLINE+”,”INCLINE-”, “SPEED+”,
“SPEED-”to set up the time that you need. The setting range is 5:00-99:00.
3. In TIME setting mode, press “MODE” button to enter into distance count-down,
the DISTANCE window will display “1.0” and glitter. Press “INCLINE+”,”INCLINE-”,
“SPEED+”, “SPEED-” to set up the distance that you need. The setting range is
0.5—99.9.
4. To set up the CALORIES, press “MODE” button to enter into calories count
down, the CAL window will display “50’ and glitter. Press “INCLINE+”,”INCLINE-”,
“SPEED+”, “SPEED-” to set up the calories that you need. The setting range is
10-999.
5. When setting is finished, press “START” button to start up, the treadmill will
run after 3 seconds, press “INCLINE+”,”INCLINE-”, “SPEED+”, “SPEED-” to adjust
the speed and the incline; press the PAUSE, the treadmill will stop.
PRESET PROGRAMS:
Press “PROGRAM” button “CAL /PULSE” window will display P1-P15 to choose the
program you like. Setting the running time, then the TIME window display will be
flashing; Display the advance setting time10:00, press “INCLINE+”,”INCLINE-”,
“SPEED+”, “SPEED-” to set up the exercise time what you need. Press “START”
button to start the inner install program, the inner install program is divided into
10 sections. Each exercise time=the setting time/10. When the system enters into
the next section, it will make 3 sound “Bi—Bi—“ and the speed will be changed
according to the setting speed of the program, then press “INCLINE+”,”INCLINE-”,
“SPEED+”, “SPEED-” to change the INCLINE and SPEED as you need. When the
program enters into the next section again, the system will make 3 sound
“Bi—Bi—“ and change to the setting speed of the program automatically.

14
PROGRAM CHART:
Each program will divide into 10 grades for the exercise time and each time sect
has the speed and incline accordingly.
Mode
Time
Form 1:TIME INTERVAL(kilometer)
1
2
3
4
5
6
7
8
9
10
P1
SPEED
2
4
3
4
3
5
4
2
5
3
INCLINE
1
2
3
3
1
2
2
3
2
2
P2
SPEED
2
5
4
6
4
6
4
2
4
2
INCLINE
1
2
3
3
2
2
3
4
2
2
P3
SPEED
2
5
4
5
4
5
4
2
3
2
INCLINE
1
2
2
3
1
2
2
2
2
1
P4
SPEED
3
6
7
5
8
5
9
6
4
3
INCLINE
2
2
3
3
2
2
4
6
2
2
P5
SPEED
3
6
7
5
8
6
7
6
4
3
INCLINE
1
2
4
3
2
2
4
5
2
1
P6
SPEED
2
8
6
4
5
9
7
5
4
3
INCLINE
2
2
6
2
3
4
2
2
2
1
P7
SPEED
2
6
7
4
4
7
4
2
4
2
INCLINE
4
5
6
6
9
9
10
12
6
3
P8
SPEED
2
4
6
8
7
8
6
2
3
2
INCLINE
3
5
4
4
3
4
4
3
3
2
P9
SPEED
2
4
5
5
6
5
6
3
3
2
INCLINE
3
5
3
4
2
3
4
2
3
2
P10
SPEED
2
3
5
3
3
5
3
6
3
3
INCLINE
4
4
3
6
7
8
8
6
3
3
P11
SPEED
3
5
8
8
9
5
7
6
3
2
INCLINE
4
5
6
6
9
9
10
12
6
3
P12
SPEED
2
5
5
4
4
6
4
2
3
4
INCLINE
3
5
6
7
12
9
11
11
6
3
P13
SPEED
2
7
4
7
8
9
4
5
3
2
INCLINE
5
6
6
4
6
5
8
9
4
2
P14
SPEED
2
6
5
4
8
6
5
2
3
3
INCLINE
5
6
5
8
4
5
5
10
6
3
P15
SPEED
2
6
5
4
8
7
5
3
3
2
INCLINE
3
4
5
6
3
5
5
6
4
3

15
Mode
Time
Form 2:TIME INTERVAL(mile)
1
2
3
4
5
6
7
8
9
10
P1
SPEED
1.2
2.4
1.8
2.4
1.8
3.1
2.4
1.2
3.1
1.8
INCLINE
1
2
3
3
1
2
2
3
2
2
P2
SPEED
1.2
3.1
2.4
3.7
2.4
3.7
2.4
1.2
2.4
1.2
INCLINE
1
2
3
3
2
2
3
4
2
2
P3
SPEED
1.2
3.1
2.4
3.1
2.4
3.1
2.4
1.2
1.8
1.2
INCLINE
1
2
2
3
1
2
2
2
2
1
P4
SPEED
1.8
3.7
4.3
3.1
4.9
3.1
5.5
3.7
2.4
1.8
INCLINE
2
2
3
3
2
2
4
6
2
2
P5
SPEED
1.8
3.7
4.9
3.1
4.9
3.7
4.3
3.7
2.4
1.8
INCLINE
1
2
4
3
2
2
4
5
2
1
P6
SPEED
1.2
4.9
3.7
2.4
3.1
5.5
4.3
3.1
2.4
1.8
INCLINE
2
2
6
2
3
4
2
2
2
1
P7
SPEED
1.2
3.7
4.3
2.4
2.4
4.3
2.4
1.2
2.4
1.2
INCLINE
4
5
6
6
9
9
10
12
6
3
P8
SPEED
1.2
2.4
3.7
4.9
4.3
4.9
3.7
1.2
1.8
1.2
INCLINE
3
5
4
4
3
4
4
3
3
2
P9
SPEED
1.2
2.4
3.1
3.1
3.7
3.1
3.7
1.8
1.8
1.2
INCLINE
3
5
3
4
2
3
4
2
3
2
P10
SPEED
1.2
1.8
3.1
1.8
1.8
3.1
1.8
3.7
1.8
1.8
INCLINE
4
4
3
6
7
8
8
6
3
3
P11
SPEED
1.8
3.1
4.9
4.9
5.1
3.1
4.3
3.7
1.8
1.2
INCLINE
4
5
6
6
9
9
10
12
6
3
P12
SPEED
1.2
3.1
3.1
2.4
2.4
3.7
2.4
1.2
1.8
2.4
INCLINE
3
5
6
7
12
9
11
11
6
3
P13
SPEED
1.2
4
3.1
4
4.8
5.5
3.1
3.7
1.8
1.2
INCLINE
5
6
6
4
6
5
8
9
4
2
P14
SPEED
1.2
3.7
3.7
3.1
5.5
4.8
3.7
1.2
1.8
1.8
INCLINE
5
6
5
8
4
5
5
10
6
3
P15
SPEED
1.2
3.8
3.1
3.1
5.5
4
3.1
1.8
1.8
1.2
INCLINE
3
4
5
6
3
5
5
6
4
3
User programs
U1, U2, U3: Besides the 15 preset programs, you can also set up another 3 user’s
programs for user’s programs as your need: U1, U2, U3.
1. User’s programs setting:
Press the button “PROGRAM”until it shows the user’s program（U1-U3）, then press
the “MODE” to enter into the setting. For the first section, press “SPEED+”、
“SPEED -”to change the speed, and press “INCLINE+”、“INCLINE -”to change the

16
incline. Press “MODE” to complete the setting of the first section and also go to the
setting of the next section till all the 10 sections are completed. The setted data
will be saved without losing due to the power off until next time when you reset it.
2. Start-up of the user’s program:
Under the standby state, press “PROGRAM”until it shows the user’s program
(U1-U3), set the running time that you need and press the “START” button for
starting the treadmill.
3. User’s program set-up explanation:
Each user’s program divides time to be ten sections, the treadmill can only be
started after the speed and the incline are set well for the 10 sections and the
running time can also be set well.
Range of programs:
SETTING CONTENT
BEGINNING
SETTING OF
BEGINNING
SET-UP
RANGE
DISPLAY
RANGE
TIME(MIN:SECOND)
0:00
15:00
5:00-99:00
0:00－99:59
INCLINE(%)
0
0
0-12
0-12
SPEED(K/h)
1.0
1.0
1.0-16
1.0-16
DISTANCE(K)
0
1.0
0.5-99.9
0.00－99.9
PULSE(hypo/min)
P
N/A
N/A
50-200
CALORIE(THERM)
0
50
10-999
0－999
BODY TESTER:
At the beginning state, press “ PROGRAM” continually to enter into the body FAT tester, press
“MODE”enter F-1, F-2, F-3, F-4, F-5 (F-1 SEX, F-2 AGE, F-3 HEIGHT, F-4 WEIGHT, F-5 FAT
TESTER), Press “SPEED+”, “SPEED -” to set F-1 ---- F-4 ( refer to the following chart), after
that, press “ MODE” to set F-5, then grasp the hand pulse, the window will display your body
quality index after 3 seconds. The body quality index is to test the relation between height and
weight, not referring to the body proportion. The body FAT suits for any male and female,
offering reference information of adjusting people’s weight. The ideal FAT should be 20-25, if
under 19, it means too thin. If between 25 and 29, it means overweight, if over 30, it means
obesity. (The data is just for reference, can not be used as medicinal data).

17
F-1
Seg
01 male
02 female
F-2
Age
10------99
F-3
Hight
100----200
F-4
Weight
20-----150
F-5
FAT
≤19
Underweight
FAT
=(20---25)
Normalweight
FAT
=(25---29)
Overweight
FAT
≥30
Obesity
Safety lock function:
Pull out the safety pulling rope, then the treadmill will stop immediately. All the
windows display“―――”，the buzzer will make 3 sound “Bi-Bi-Bi”, and the treadmill
become stopped. Attach the magnet end of the safety lock to the console, the
treadmill will be at the beginning of running.
Save on power function:
The system is with SAVE-ON power function.Under the standby state, without
operating the treadmill for 10 minutes, the SAVE-ON power function will be
available, and the display will be closed up. You can press any button to re-wake
up the display.
MP3(Option):
When Mp3 is connected, the console is able to play music. The volume is controlled
on the Mp3. Please pay attention to adjust the volume properly for having better
timbre and protecting the inner voice-frequency circuit.
Turn off:
Turn off the power: You can turn off the power to stop the treadmill, so that the
treadmill won’t be damaged at any time.
Caution:
1. We recommend that you maintain a slow speed in the beginning of exercise and
hold on the handrails until you become comfortable and familiar with the
treadmill.
2. Attach the magnet end of the safety lock to the console and also attach the clip
of the safety pulling rope to your clothing.
3. To end your workout safely, press the PAUSE button or pull out the safety
pulling rope, then the treadmill will stop immediately.

18
EXERCISE INSTRUCTIONS
1. The Warm Up Phase
This stage helps to get the blood flowing around the body and the muscles working properly.
It will also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching
exercises as shown below. Each stretch should be held for approximately 30 seconds, do not
force or jerk your muscles into a stretch - if it hurts, STOP.
2. The Exercise Phase
This is the stage where you put the effort in. After regular use, the muscles in your legs will
become stronger. It is very important to maintain a steady tempo throughout. The rate of work
should be sufficient to raise your heart beat into the target zone shown on the graph below.
This stage should last for a minimum of 12 minutes.
3. The Cool Down Phase
This stage is to let your Cardio-vascular System and muscles wind down. This
is a repeat of the warm up exercise e.g. reduce your tempo, continue for
approximately 5 minutes. The stretching exercises should now be repeated, again
remembering not to force or jerk your muscles into the stretch.
As you get fitter you may need to train longer and harder. It is advisable to train at
least three times a week, and if possible space your workouts evenly throughout
the week.
To tone muscle while on your Treadmill you will need to have the resistance set
quite high. This will put more strain on our leg muscles and may mean you cannot
train for as long as you would like. If you are also trying to improve your fitness
you need to alter your training program. You should train as normal during the
warm up and cool down phases, but towards the end of the exercise phase you
should increase resistance, making your legs work harden than normal. You may
have to reduce your speed to keep your heart rate in the target zone.
The important factor here is the amount of effort you put in. The harder and
longer you work the more calories you will burn. Effectively this is the same as if
you were training to improve your fitness, the difference is the goal.
MAINTENANCE INSTRUCTIONS

19
WALKING BELT CENTERING AND TENSION ADJUSTMENT
DO NOT OVERTIGHTEN the walking belt. This may cause reduced motor
performance and excessive roller wear.
TO CENTER WALKING BELT:
● Place treadmill on a level surface
● Run treadmill at approximately 3.5 mph
● If the belt has drifted to the right, turn the right adjusting bolt 1/2 turn clockwise
and the left adjusting bolt 1/2 turn counterclockwise
● If the belt has drifted to the left, turn the left adjusting bolt 1/2 turn clockwise
and the right adjusting bolt 1/2 turn clockwise and the right adjusting bolt 1/2 turn
counterclockwise
Picture A. If the belts has drifted to the LEFT Picture B. If the belts has drifted to the RIGHT
WARNING: ALWAYS UNPLUG THE TREADMILL FROM THE ELECTRICAL OUTLET
BEFORE CLEANING OR SERVICING THE UNIT.
PIC A
PIC B