Fizz Creations Slush Puppie User manual

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE 1
SLUSH PUPP E®MAKER
INSTRUCTIONS FOR USE
Product Ref: 9041_v11. Voltage: 220-240V 50/60Hz. Power: 20 Watts.

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE
2
Safety Information 2
Before You Begin 3
– Remove Packaging
– What’s in the box
– What you will need
– Tips on using your SLUSH PUPPiE Maker
Assembly 4-5
Using the Machine 5-6
– Making Slush Puppies
– Dispensing Slush Puppies
Storage and Maintenance 7
– Cleaning and Care
– Storage
– Servicing
– Troubleshooting
– Helpful Hints and Tips
– Technical Specication
✘Never use any attachments or tools not included with the
SLUSH PUPPiE Maker. The use of these attachments may
cause, re, electric shock or injury.
✘Never use the SLUSH PUPPiE Maker for anything other than
its intended use. The appliance is for household use only. This
appliance is used indoors only. This appliance is intended to be
used in household and similar applications: staff kitchen areas in
shops, ofces and other working environments; farm houses; by
clients in hotels, motels and other residential type environments;
bed and breakfast type environments.
✘Never allow children to use the SLUSH PUPPiE Maker,
close supervision is necessary when this appliance is in use
near children.
✘Never let the power cord hang over the edge of the worktop,
touch hot surfaces, become knotted, trapped or pinched.
✘Never place on or near a heat source.
✘Never leave the SLUSH PUPPiE Maker unattended during use.
✘Never touch the exposed metal parts of the appliance during
use as they will become very hot.
✘Never operate the SLUSH PUPPiE Maker by means of an
external timer or separate remote control system.
✘Never immerse the power cord or plug into water or any other
liquid. This is to protect against electric shock.
✔Always ensure the SLUSH PUPPiE Maker is only used by a
responsible adult.
✔ Always use the SLUSH PUPPiE Maker on a stable
level surface.
✔Always ensure that hands are dry before handling the plug or
switching on the SLUSH PUPPiE Maker.
✔Always unplug this unit when not in use and before cleaning.
✔Always allow the SLUSH PUPPiE Maker to fully cool down
before cleaning or storing.
✔Always carry out regular checks on the SLUSH PUPPiE Maker
and power cord.
• A 3 amp BS1362 ASTA approved fuse must be tted.
• There are no user serviceable parts inside the SLUSH PUPPiE
Maker. In order to avoid hazard always refer servicing to a
qualied service personnel.
• Do not allow the SLUSH PUPPiE Maker to be exposed to rain or
moisture during use or storage.
• Before switching on, make sure that the voltage of your electricity
supply is the same as that indicated on the SLUSH PUPPiE
Maker’s rating plate. Connecting it to any other power source may
cause damage.
• The mains lead of the SLUSH PUPPiE Maker is not replaceable by
the user. If the mains lead is damaged, the entire SLUSH PUPPiE
Maker should be replaced by a suitable qualied person in order to
avoid hazard. In order to avoid hazard if the plug has to be changed
because it is not suitable for your socket, or due to damage, it
should be cut off and a replacement tted by a qualied person.
In order to avoid hazard, should there be any sign of damage, do not
attempt to use or repair. If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard. The SLUSH PUPPiE Maker has
no user serviceable parts.
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children
unless they are older than 8 and supervised.
• Keep the appliance and its cord out of reach of children less
than 8 years.
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND USING YOUR SLUSH PUPPIE MAKER.
WE RECOMMEND YOU KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE USING THE SLUSH PUPPIE MAKER
OR CONNECTING IT TO THE MAINS ELECTRICITY SUPPLY.
Electrical Safety
safety information
contents
Watch a Video
For top tips and guidance on
making perfect Slush Puppies
a video can be found at:
slushpuppie.zzcreations.com
or simply scan here.

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE 3
before you begin
Remove Packaging
Carefully remove all packaging material and promotional labels from the SLUSH PUPPiE Maker.
What’s in the box
In the box you will nd...
1Ice/Salt Inlet Cap
2Ice/Salt Inlet
3Canister Lid
4Locking Catch
5Syrup Inlet
10 Slush Puppie Container
11 Locking Notch
12 Tap Handle
13 Tap
6Ice Canister Cage with Ice Paddle
Locking Clips
7Ice Canister
8Ice Paddle Assembly
9Slush Puppie Blades
14 Motor Base
15 Drive Sprocket
16 Mix/Off/Dispense Switch
17 Drinks Tray
Canister Lid Slush Puppie ContainerIce Canister
Motor Base
10 11
13
12
1
2
3
4
5
6
8
7
9
14
17
15
16
Ice Canister
Motor Base
Ice Canister
Slush Puppie
Container
Once you’ve chosen a avour, make the Slush Puppie
syrup mixture in a jug that will hold at least 1 litre of
mixture. Carefully follow the instructions on the syrup
bottle. To make 1 litre of Slush Puppie, mix 835ml
of water to 165ml syrup. This is a guide and should
your mixture not produce the desired slush, you can
add more water or syrup as necessary. If the mixture
is not freezing enough to produce slush, it is likely you
will need more water. If the mixture is becoming too
solid it is likely you will need more syrup.
To make perfect Slush Puppies chill your mixture
for a minimum of 2 hours but ideally overnight. If the
mixture is too warm, chilling or freezing within the Ice
Canister will not take place. For faster Slush Puppies
and the best results we recommend freezing the Ice
Canister for 1 hour before making Slush Puppies. Do
not freeze the Ice Canister for longer than this as it will
become too cold.
What you will need…
Ice Cubes
Make sure you have enough
ice cubes on hand to ll the
Ice Canister.
Water
At least 80ml of cold water.
Salt
We recommend you have enough
salt to ll 7 Ice/Salt Inlet Caps. This
is equivalent to approximately 170g
NOTE: The salt will not be
consumed; it is used to stop the ice
mix from rapidly freezing.
Cups
Use your own, or purchase
the Slush Puppie Cups (9oz).

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE
4
Hexagonal
Socket
Slush Puppie
Container
Top of
Couple
Ice Canister
Ice Canister
Cage
Hexagonal
Socket
Hexagonal
Mount
Ice Canister
4Insert the assembled Ice Canister
into the Slush Puppie Container.
Make sure the Hexagonal Socket on
the Ice Canister aligns with the top
of the Coupler in the Slush Puppie
Container and slots rmly into place.
Canister
Lid
Locking Catch
Locking Notch
Central Spindle
of Ice Paddle
Mount on
underside of
Canister Lid
Ice Canister
Cage Ice
Canister
Ice Paddle
Assembly
Indent
Clips
Indents
Slush Puppie
Container
Tap
Motor Base
Coupler
Drive
Sprocket
Drinks Tray
1Insert the Slush Puppie Container
onto the Motor Base. Make sure
the Coupler on the Slush Puppie
Container is correctly aligned with
the Drive Sprocket and slots rmly
into position. The Tap should sit
directly above the Drinks Tray.
3Insert the Ice Canister complete
with Ice Canister Cage into the Ice
Paddle Assembly so that the Clips
line up with the 3 Indents. Make
sure the Ice Canister is correctly
seated. Carefully push each Clip
into place. A loud ‘click’ will indicate
each Clip is securely in position.
2Insert the Ice Canister Cage
into the Ice Canister. Make
sure the Hexagonal Socket on
the Ice Canister Cage aligns
with the Hexagonal Mount in
the Ice Canister.
5Fit the Canister Lid into
place. Make sure the
Slush Puppie logo is at
the front and the text
displaying FRONT on
the Canister Lid is facing
forwards. Push down
on the front of the lid
and then the rear. The
Central Spindle of the Ice
Paddle assembly should
be rmly in place in the
mount on the underside
of the Canister Lid.
Secure the Locking
Catch onto the rear
Locking Notch of the
Slush Puppie Container.
Your SLUSH PUPPiE Maker can make a maximum of 1 litre of Slush Puppie mix in one go.
PLEASE NOTE that the Slush Puppie mix will reduce in volume when the slush starts to form.
DO NOT exceed the maximum capacity of 1 litre of liquid in the Slush Puppie Container as indicated by the ‘Max Fill’ level
on the front of the container. This will result in the liquid overowing into the Ice Canister, mixing with the salt and ice.
TIP: Using Your SLUSH PUPPiE Maker
assembly
It’s almost time for some Slush Puppies.
First, let’s get the SLUSH PUPPiE Maker ready for action…
DO NOT plug the power cord into the mains electrical supply until the SLUSH PUPPiE Maker is fully assembled. Before using for
the rst time, clean any removable parts with a soft sponge and washing up liquid. Thoroughly rinse with clean water and dry.

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE 5
x2
Motor Base
Drinks Tray
assembly
6Push the Inlet Cap into position in
the Ice/Salt Inlet.
7Carefully pull the Drinks Tray out from
the Motor Base until it is fully extended.
Inlet Cap
Ice/Salt Inlet
Canister
Lid
using the machine
Making Slush Puppies
Are you ready? Feeling thirsty?
Let’s make some Slush Puppies!
Watch a Video
For top tips and guidance on
making perfect Slush Puppies
a video can be found at:
slushpuppie.zzcreations.com
or simply scan here.
1Plug the SLUSH PUPPiE Maker
into an appropriate mains power
supply and check that it is
switched on at the socket.
2Press the Mix/Off/Dispense
switch to position I (Mix).
Tap in closed
position
3Ensure the Tap is in the
closed position.
IMPORTANT
It is very important that your
SLUSH PUPPiE Maker is working
before you add ice; otherwise the
motor or blade could freeze.
4Remove the Inlet Cap and half ll
the Ice Canister with ice through
the Ice/Salt Inlet. This is indicated
by the ICE and SALT marker on
the Canister Lid.
5Pour 2 inlet caps of salt into the
Ice/Salt Inlet.
IMPORTANT
Add salt to the Ice Canister only.
The salt will not be consumed;
it is used to stop the ice mix
from rapidly freezing.
40ml
6Pour 40ml of water into the Ice
Canister through the Ice/Salt Inlet.
7Fill the rest of the Ice Canister with
ice cubes through the Ice/Salt Inlet.
Note: The ice level should be at least
3cm below the rim of the Ice Canister.

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE
6
x3
using the machine
8Pour a further 3 Inlet Caps of salt
into the Ice Canister through the
Ice/Salt Inlet. 10 Re-t the Inlet Cap into position
on the lid.
9Pour a further 40ml of water into
the central Ice Canister.
40ml
12 Leave the SLUSH PUPPiE Maker running
for approximately 15-25 minutes. Do
not leave the SLUSH PUPPiE Maker
unattended or exceed the running time
(40 minutes). The amount of time until
the desired consistency is reached will
depend on the ambient temperature.
13 When the mixture level drops add more
ice cubes to the Ice Canister to a level no
higher than 3cm from the rim of the Ice
Canister. Do not ll the ice to the top of
the canister as this cools the Ice Canister
too much; add a couple of ice cubes at
a time and leave a minute or two before
adding more ice cubes. Add 2 or 3 Inlet
Caps of salt to the Ice Canister and the
equivalent amount of water.
Note: If the Ice Canister jams,
simply turn the machine off and
wait for the ice to melt around
the canister, enough to allow the
blades to rotate again. Once this
has melted enough, add ice again,
slowly and regularly to cool the
canister enough to make slush.
14 To create perfect Slush Puppies,
wait until peaks form in the Slush
Puppie mixture before dispensing.
Note: After using the SLUSH PUPPiE
Maker wait at least 15 minutes before
using again. This will allow the motor
to cool.
1Press the Mix/Off/Dispense switch to Position II (dispense).
2Place a cup or glass onto the Drinks Tray and turn the Tap Handle clockwise so
that it is in the open position. The mixture will start to pour.
3To stop dispensing, turn the Tap Handle anti-clockwise.
4When you have nished, press the Mix/Off/Dispense switch to Off (Position O).
Dispensing Slush Puppies
Tap in
open
position
IMPORTANT
DO NOT exceed the 1 litre limit as
shown by the Max Fill line on the
Slush Puppie Container.
11 Slowly pour your Slush Puppie
syrup mixture through the Syrup
Inlet at the rear right of the
Canister Lid. This is indicated
by the BEVERAGES HIGH IN
SUGAR CONTENT ONLY marker
on the Canister Lid. Not suitable
with carbonated beverages.
IMPORTANT
Add salt to the Ice Canister only.
The salt will not be consumed;
it is used to stop the ice mix
from rapidly freezing.
IMPORTANT
Add salt to the Ice Canister only.
The salt will not be consumed;
it is used to stop the ice mix
from rapidly freezing.

SLUSH PUPPiE®MAKER – INSTRUCTIONS FOR USE 7
Storage and Maintenance
To safely store your SLUSH PUPPiE Maker:
1Make sure the SLUSH PUPPiE Maker is turned off with
the Mix/Off/Dispense switch set to Off (Position O).
2Unplug the SLUSH PUPPiE Maker from the mains
electricity supply.
3Make sure the SLUSH PUPPiE Maker has completely cooled and
is clean before storing.
4Store the SLUSH PUPPiE Maker in its original packaging in a
clean dry place. Do not allow the SLUSH PUPPiE Maker to be
exposed to rain or moisture during use or storage.
• Do not add thick liquids or solids to the Slush mix.
• Do not operate the SLUSH PUPPiE Maker for longer than required
and do not use for longer than 40 minutes of continuous use.
• Consume Slush Puppies as soon as they have been served.
• Slush mixtures with higher sugar content will reach the desired
consistency more quickly than mixtures with lower sugar content.
• When preparation begins always start with liquid mixtures and not
frozen mixtures.
• Follow the instructions on the syrup bottle carefully.
We recommend you use the SLUSH PUPPiE branded syrup.
• You can use any drink with a high sugar level in your SLUSH PUPPiE
Maker such as fresh orange juice.
• If you are not using ofcial SLUSH PUPPiE branded syrup please
ensure your mixture has a high sugar content which helps with the
reaction to create the slush. If the mixture is not freezing sufciently
to produce slush, there is too much sugar in the mixture and it will
need to be diluted. If the mixture is becoming too solid, it is likely
you will need more sugar in your mixture.
If your SLUSH PUPPiE Maker is not working as expected you may nd a simple solution listed below:
If you drop or damage your SLUSH PUPPiE Maker do not use it until it has been examined by an authorised service centre
or appliance technician. Servicing must only be carried out by qualied service personnel.
The SLUSH PUPPiE Maker is for household use only.
Storage
Helpful Hints and Tips
Troubleshooting
Servicing
Whats is happening? What it could be
The motor is not spinning The blade may have become frozen. Turn the SLUSH PUPPiE Maker off, move the frozen
blade and restart the machine.
The mixture is not freezing
or chilling
The Ice Canister may not be cold enough. Add more ice and salt. The mixture added is too
warm. We recommend chilling the syrup mixture for at least 2 hours, ideally overnight before
use. For best results, freeze the Ice Canister for 1 hour before use.
If the SLUSH PUPPiE Maker is
getting too cold too quickly
Too much ice is being used. When lling the Ice Canister leave a gap
of 3cm from the top of the ice to the canister rim.
If the Canister Lid
comes off
Too much ice is being used. When lling the Ice Canister leave a gap of
3cm from the top of the ice to the Ice Canister rim.
If your SLUSH PUPPiE Maker is
not making slush
This could be due to salt falling into the wrong compartment. Make sure salt is only poured into the
Ice/Salt Inlet indicated by the ICE AND SALT marker on the Ice Canister Lid.
We recommend cleaning the Ice Canister straight after use. There is
a large amount of salt used when making Slush Puppies. This salt is
not consumed and prevents freezing.
If the salt is left in the Ice Canister for a long period of time it will
corrode the metal. Please refer to the steps below:
To clean your SLUSH PUPPiE Maker:
1Unplug the SLUSH PUPPiE Maker from the mains electricity
supply and allow it to cool completely.
2Remove all detachable parts.
Note: When removing the Canister Lid, press the Clip and the rear
inwards to release the Canister Lid. Please take care when handling
any sharp edges or parts during cleaning.
3Clean the detachable, non-electronic parts in lukewarm water
with some washing-up liquid and rinse them under a tap.
4Clean the outer surface of the SLUSH PUPPiE Maker with a
soft damp cloth.
5After each use please clean the Ice Canister thoroughly. The Ice
Canister is sturdy but the metal is purposely designed to be thin.
Salt must not be left in or on the Ice Canister after use as it can
cause corrosion. The ultra-thin Ice Canister allows the freezing cold
temperatures to transfer to the outer wall, this design helps you to
make perfect Slush Puppie.
Cleaning and Care
IMPORTANT
DO NOT immerse the Motor Base in
water or any other liquids.
IMPORTANT
DO NOT use coarse or abrasive cleaners or steel
wool to clean the SLUSH PUPPiE Maker.
IMPORTANT
Never spray or apply cleaning products directly
onto the SLUSH PUPPiE Maker. If necessary, apply
cleaner to a soft cloth instead.
IMPORTANT
DO NOT use a dishwasher to clean your
SLUSH PUPPiE Maker.
IMPORTANT
Before cleaning your SLUSH PUPPiE Maker, make
sure the machine is turned off with the Mix/Off/
Dispense switch set to Off (Position O).
Voltage: 220–240 V 50/60 Hz
Power: 20 Watts
Capacity: 1 litre
Technical Specication

WARNING!
– This product is not a toy.
– WEEE products must be disposed of by handing it over at a designated collection point.For more information
about where you can drop off your waste product for recycling please contact your local authority.
© 2020 SLUSH PUPPiE®. SLUSH PUPPiE® is a registered trademark of The ICEE Company, a Subsidiary of J&J Snack Foods Corp.