Flash Furniture BT-7615-BK-CURV-GG User manual

Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or componenets
may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
Injury may result from tipping furniture. You must install the Tipping Restraint Hardware with the unit to prevent
the unit from tipping and causing any accidental injury, instability, death or damage. The tipping restraint is
intended only as a safety measure, it is not a substitute for proper adult supervision.
This tipping restraint is not an earthquake restraint. If you wish to add the extra security of earthquake
restraints, they must be purchased and installed separately.
Serious or fatal crushing injuries can occur from furniture tipping over. To prevent furniture from tipping over it
ferent wall materials
Failure to detach this restraint before moving furniture may result in injury or damage.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
ASSEMBLY INSTRUCTIONS
Customer Service email: [email protected] | phone: [phone]
BT-7615-BK-CURV-GG / BT-7615-BN-CURV-GG
Thank you for your purchase!
LeatherSoft Recliner and Ottoman
with Swiveling Maple Wood Base
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/BT-7615-BK-CURV-GG.pdf

(2)
(9)
(5)
(1)X1
(7)X2 (8)X4 (9)X4 (10)X1 (11)X1 (12)X1 (13)X1
(3)X 1 (4)X 1 (5)X4 (6)X 4
STEP 1
STEP 3
STEP 5
STEP 2
STEP 4
PARTS
(2)X 1(L )X1(R )
M6*45mm Bolt
M8*25mm Bolt & Nut
6.5*18*1.5mm
(7)
(1)
(10)
(4)
(6)
(8)
(3)
(6)
(8)
M6*50mm Bolt
6.5*15*1.5mm
Chair
Arm Cushions
Ottoman Cushion Ottoman Base
Tilt Tension Knob
Small Allen Wrench Large Allen Wrench Open End Wrench
STEP 1: Move seat back
to the upright position and
lock into place using (1)
M8*25mm Bolt and Nut
Set (Part 7) to attach back
and seat frames. Chair
M8*25mm Bolt and Nut Set
STEP 2: Attach Arm Cushions (Part 2) to
the left and right arms using (4)
6.5*18*1.5mm Washers (Part 9) and (4)
M6*50mm Bolts (Part 5)
STEP 3: Insert Tilt Tension
Knob (Part 10) into hole
beneath the chair seat.
Tilt Tension Knob
STEP 4A: Lay Ottoman
Cushion (Part 3) face down
on a soft clean surface
Ottoman Cushion
STEP 4B: Attach Ottoman Base (Part 4) to
underside of the Ottoman Cushion using
(4) 6.5*15*1.5mm Washers (Part 8) and (4)
M6*45mm Bolts (Part 6)
Ottoman Base
M6*45mm Bolt
6.5*15*1.5mm Washer
STEP 5: Return Ottoman to the upright
position and place in front of the recliner
Seat Back
Arm Cushions
6.5*18*1.5mm
Washer
M6*50 Bolt
M6*50 Bolt
M6*45mm Bolt
6.5*15*1.5mm Washer
6.5*15*1.5mm Washer
M6*45mm Bolt
M6*45mm Bolt
6.5*15*1.5mm Washer