Flash Furniture GO-1691-1-BK-GG User manual

Swivel Task Chair
(Arms Sold Separately)
GO-1691-1-BK-GG,GO-1691-1-ORG-GG,GO-1691-1-PINK-GG,GO-1691-1-BLUE-GG, GO-1691-1-PUR-GG,GO-1691-1-GREEN-GG,GO-1691-1-GY-GG
GO-1691-1-BK-A-GG,GO-1691-1-ORG-A-GG,GO-1691-1-PINK-A-GG,GO-1691-1-BLUE-A-GG, GO-1691-1-PUR-A-GG,GO-1691-1-GREEN-A-GG,GO-1691-1-GY-A-GG
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email: [email protected] | Phone: [phone]
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/GO-1691-1-BLUE-GG.pdf

PARTS
STEP 1 STEP 2 STEP 3
STEP 4
STEP 5 STEP 6
(11 (2)*1 (3)*1(L)*1(R) (4)*1
(5)*1 (6)*1
(11)*6 (12)*1
(10)*4
(9)*4
(8)*5
(7)*1
(11)
(8)
(7)
(5)
(6)
(1)
(3)
(2)
(5)
(6)
(7)
(8)
(4)
(3)
(3)
(2)
(3) (3)
(4)
(2)
(1) (10)
(3)
(4)
(2)
(3)
(9)
Chair Back Seat
Left Arm Right Arm
Only for models
with arms. Will
not be included
with armless
model.
Lift Mechanism
Gas Lift Cylinder Cylinder Cover
Base
Casters
Allen Wrench
STEP 1A: Place cylinder
cover (Part 6) over Gas Lift
Cylinder (Part 5) then insert
Gas Lift Cylinder into the Base
(Part 7)
Gas Lift Cylinder
Cylinder Cover
Base
Casters
Step 1B:
Attach (5)
casters (Part 8)
to Base
STEP 2: (Only for models with included arms)
Attach Left and Right Arms (Part 3) to Seat (Part 2) using (6)
long bolts (Part 11)
Right Arm
Left Arm
Seat
Long Bolts
STEP 3: Attach Lift Mechanism (Part 4) to the underside of the
Seat using (4) Short Bolts (Part 9). Note: Lever Arm should be
pointing toward the Right Arm.
Right Arm Left Arm
Lift Mechanism
Seat (Underside View)
Lever Arm
Short Screws
Long Bolts
Medium Bolts
Short Bolts
STEP 4: Attach Chair Back (Part 1) to underside of Seat using (4)
Medium Bolts (Part 10)
Seat (Underside View)
Lift Mechanism
Left Arm
Right Arm
Chair Back
Medium Bolts
STEP 5: Place assembled seat onto the Gas Lift Cylinder
Seat Back
Left Arm
Seat
Gas Lift Cylinder
Cylinder Cover
Base
Casters
Lift Mechanism
Right Arm
(3)
STEP 6: Ensure all bolts
are securely tightened