Flash Furniture WX-5L203-X-BK-GR-GG User manual

ASSEMBLY INSTRUCTIONS
WX-5L203-X-BK-GR-GG WX-5L203-X-WH-GR-GG
Thank you for your purchase!
4 Drawer Storage Chest
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components
may result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death
or damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety
Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email: [email protected] | Phone: [phone]
Online Assembly Instructions: http://ftp.flashfurniture.com/AssemblyInstructions/WX-5L203-X-BK-GR-GG.pdf

PARTS
STEP 2
STEP 3
STEP 1
2pc
1
6pcs
4
11 pc
1
①
②
2
2
4
8
5
4
1
③
④
⑤
⑥
⑦
⑨
4
2
1
5
2
2
⑧
⑩
11
12
13
54pcs
3
pcs
2
11 pcs
1
2
6
6
6
2
1A
3
1B
3
5
5
5
5
AB
1
14
13 pcs2
12 pc1
14 pc1
pcs16
12
12
6
6
13 13
Side frame
Wooden top
Adjustable leveler
M6X25mm
M6X10mm
Rear Bars
Open End
Frame Pole
M6X25MM Screw
Hex Wrench
Left Side Frame
Right Side Frame
Wooden Top
STEP 1: Attach Left Frame (Part 1A) and
Right Side Frame (Part 1B) to the Frame Poles
(Part 3) using (4) M6x25mm Screws (Part 5)
STEP 2: Place the Wooden Top
(Part 2) with screw holes facing down
and attach to the frame using (4)
M6x10mm Screws (Part 6)
Wooden Top
M6x10mm Screws
Hex Wrench
Wooden Top
Rear Bars
Open End
Hex Wrench
Hex Cap
M6x10mm
STEP 3: Attach Rear Bars (Part 13) together
using (1) M6x10mm Screw (Part 6) and (1) Hex
Cap (Part 12). Tighten with Open End Hex
Wrench (Part 14)

4pcs4
12 pcs4
54pcs
4
4
4
4
5
5
5
12
12
12
12
STEP 4
STEP 5
STEP 8
pcs
4
7
8
7
7
STEP 6
STEP 7
10
10
Top: Max static weight capacity 40 lbs.
Drawer: Max weight capacity 5 lbs.
7
pcs
4
8
9
8
10
14 pc1
Adjustable Leveler
M6x25mm
Hex Cap
Open End
Hex Wrench
STEP 4A: From the inside of the
frame, attach the rear bars to the
frame using (4) M6x25mm Screws
(Part 5) and (4) Hex Caps (Part 12).
Tighten with Open End Hex
Wrench (Part 14)
STEP 4B: Attach Adjustable Levelers (Part 4)
to the bottom of the frame legs. Turn clockwise
to tighten.
STEP 5: Unfold (4) Fabric Drawers (Part 7) and place Drawer Flooring (Part 8) into the drawer with the pull
strap facing up.
Fabric Drawers
Drawer Flooring
STEP 6: Insert drawers
into the assembled frame
STEP 7: Insert (2) Wall Anchors (Part 10) into the drywall
Note: A power drill is required to make pre-drilled holes for
wall anchors
STEP 8: Insert Wall Mount Screw (Part 9) through the hole in the frame and
into the Wall Anchors.