Flashforge Adventurer 5M Pro User manual

快速启动指南
Quick Start Guide
中文P11
EN/CN - A01 Adventurer 5M Pro / 冒险家5M Pro
1. Please refer to this Guide for initial printer setup.
2. Hot! Avoid touching the heating nozzle in operation.
3. Moving parts in the printer may cause injuries. Do not wear
gloves or other sources of entanglement in operation.
1. 请参照本指南完成打印机的初始准备。
2. 高温危险！打印机喷嘴在工作时会被加热，操作时请避免接触！
3. 可动部件可能会造成卷入挤压和切割伤害。操作机器时请不要
佩戴手套或缠绕物。
Do not power on the printer until installation is completed.
请勿在打印机安装完成之前通电。
安全提示
Safety Notice

For more information, you can visit the Flashforge official website.
www.flashforge.com - [Support]
更多产品相关资料您可以登陆闪铸官网查看。
www.sz3dp.com - [技术支持]

01
1. Open the box. 2. Remove the upper foam packaging,
Quick Start Guide and After-sales Service
Card.
3. Take out the machine, place it on a level
workspace and remove the packaging
bags and tapes.
4. Open the top cover and remove the
upper protective foam.
Unboxing Instructions
5. Remove the filament, power cable, and accessory
box from the chamber protective foam. Remove
the inner protective foam from the extruder.

7. Remove the foam.
6. Move the extruder and chain according to the arrow direction.
02

Packing List
3D Printer Filament After-sales
Service Card
Spool Holder
(with 2 screws)
0.6mm Nozzle
Quick Start Guide Grease
Power Cable
USB Disk
Glue
Diagonal Pliers
Allen Wrench Set
2.0 2.5 3.0
Screwdriver
Unclogging Pin Tool
03

Printer Components
1
2
3
4
5
9
10
7
8
6
11 12 13
1. Top Cover
2. Extruder
3. Switch Button
4. Touch Screen
5. Front Door
6. Auxiliary Cooling Fan
7. Build Plate
8. USB Port
9. Air Filter
10. Screw Holes for Spool Holder
11. Ethernet Input
12. Power Switch
13. Power Socket
04

1. Take out the two screws and spool holder from
the accessory box.
2. Install the spool holder at the position shown
in the figure with the two screws.
Please tighten them using a
2.0mm Allen wrench.
Install the Spool Holder
05
Note

Please ensure the platform has been cleared up.
Please use a 2.0mm Allen wrench to remove four screws which lock the build plate (as indicated
by the arrow).
Unlock the Build Plate
06
Note

1. Connect the power, turn on the power switch, and press
the switch button to turn on the screen.
* The interface layout may change whenever there is an upgrade of firmware.
Power switch
2. Following the guide on the screen, select
the language.
3. Click [Next] according to screen prompts and the machine will perform the first calibration.
Vibrations and noise during calibration are normal. (Note: Please keep the machine on a
stable surface and do not move it during calibration.)
First Print
07
Switch button

4. Load filament following the on-screen startup boot:
a. Cut off the bent part of the filament end.
08
C1. Click [Load] and select [PLA] for the first print. C2. Wait for the extruder to heat up.
b. Hang the filament on the spool holder. Pass it through the filament sensor until it’s seen
from the other end of the filament guide tube. Push it forward to the feed roller, until it
can not go further. (Please use PLA filament for the first print on initial setup).

6. Click [Print] and the machine starts printing
the built-in file (configured for PLA material).
5. Please clear the filament residues on the nozzle
and platform. Users must apply glue to the platform
so as to improve adhesion for the first print.
09
C3. Feeding will begin after heating. Successful filament extrusion from the nozzle indicates
successful loading. Lastly, confirm the filament guide tube is properly inserted.
If no filament is extruded, manually insert the filament into the inlet and click [Back]
to retry. Feel for filament movement until it is extruded.
Note

Parameters
Machine Name
Extruder Quantity
Printing Precision
Positioning Accuracy
Layer Thickness
Build Volume
Nozzle Diameter
Printing Speed
Max Acceleration
Max Travel Speed
Max Extruder Temperature
Supported Filament
Power Supply
Device Size
Net Weight
Connectivity
Operating Temperature
Compatible Operating System
Slicing Software
Max Platform Temperature
Leveling Method
Filament Run-out Reminder
Power Loss Recovery
Smart Touch Screen
Remote Video Monitoring
Time-lapse Video
Air Filtration
Build Plate
Automatic Shutdown
Adventurer 5M Pro
1
±0.2mm [testing based on 100mm cubes]
X/Y-axis: 0.0125mm, Z-axis: 0.0025mm
0.1-0.4mm
220 x 220 x 220mm
0.4mm default [0.6/0.8/0.25mm optional]
10-300mm/s
20000mm/s²
600mm/s
280℃
*PLA/*PETG/*TPU [0.4mm nozzle]
ABS/ASA
PLA-CF/PETG-CF [0.6/0.8mm nozzle]
Input: AC 100~240V, 50/60Hz, 350W
380 x 400 x 453mm [excluding the spool holder]
14.6kg
USB/Wi-Fi/Ethernet
15-30℃
Windows 7/8/10/11; Linux support version Ubuntu
20.04 or later; Mac OS support version 10.9 or later.
FlashPrint 5 / Orca / Prusa / Cura
110℃
One-click auto leveling
√
√
4.3-inch
√
√
Internal circulation + external circulation
[HEPA + activated carbon]
PEI flexible steel plate
√
* Note: Materials marked with * are recommended for printing.
10

1. 打开纸箱。 2. 取出上方固定泡棉以及快启售后服务卡。
3. 取出机器放置水平桌面，去除包装袋和
固定胶带。
4. 打开机器上盖，取出上部保护棉。
产品开箱
5. 取出腔体保护棉内的耗材、电源线、配件盒
和喷头内侧保护棉。
11

7. 取出泡棉，完成开箱。
6. 按照箭头方向移动喷头和链条。
12

装箱清单
3D打印机 耗材 售后服务卡
料盘支架
[含两颗螺丝]
0.6mm 口径喷嘴
快速启动指南 润滑脂
电源线
U盘
水洗胶
斜口钳
内六角扳手
2.0 2.5 3.0
十字螺丝刀
通针
13

部件介绍
1
2
3
4
5
9
10
7
8
6
11 12 13
1. 上门板
2. 喷头
3. 开关机键
4. 显示屏
5. 前门板
6. 辅助散热风扇
7. 打印平台
8. USB接口
9. 空气滤芯
10. 料盘支架安装孔
11. 网线接口
12. 电源开关
13. 电源接口
14

1. 取出配件盒中的两颗螺丝和料盘架。
2. 用两颗螺丝将料盘架固定在如图背板位置
（注意：请用2.0mm内六角扳手拧紧固定）。
安装耗材架
15

请确认打印平台无异物！
用2.0mm内六角扳手取下图示中的4颗螺丝（可参照机器上箭头标识），解锁打印平台。
解锁平台
注意事项
16

1. 连通电源，打开电源开关，点击开机键点亮屏幕。
* 固件不定期更新，UI界面请以实际为准。
电源开关
开机键
2. 根据屏幕上的开机指引完成界面语言选择。
3. 根据屏幕提示，点击[下一步]，机器进行首次校准。校准过程中出现震动和噪音属于正常现象。
（注：请将机器放置于稳定的平台面，且校准过程中请勿移动机器。）
首次打印
17

4. 根据屏幕开机指引完成耗材安装进丝操作：
a. 剪去耗材头部弯折部分。
b. 将耗材挂在耗材架上，穿过丝料传感器，直至从导丝管一端看到丝料，将丝料推送到送丝轮处，
直到无法再推入（*首次开机请使用PLA耗材进行第一次打印）。
18
C1. 点击进丝，首次选择默认[PLA]。 C2. 等待喷头加热。