Flashforge Creator 3 Pro User manual

快速启动指南
Creator 3 Pro / 金刚狼3 Pro
Quick Start Guide
EN/CN/DE/FR/한-A01
本手册仅适用于闪铸科技 金刚狼3 Pro 3D打印机
This guide is only applicable to FLASHFORGE Creator 3 Pro 3D printer
EN P01 / CN P09 / DE P17 / FR P25 / 한 P33
WARNING
注意事项
1. Hot! Avoid touching the heating nozzle and heating build plate in
operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。

Creator 3 Pro Quick Start Guide
Creator 3 Pro Introduction
01
3
4
10
12 13 14
11
5
6
7
8
9
21
1. Touch screen
2. USB disk port
3. Right extruder
4. Left extruder
5. Nozzle brush
6. Build plate
7. Leveling nut
8. Filament holder cover
9. Filament holder cover handle
10. Wind guide nozzle
11. Nozzle
12. Ethernet port
13. Power switch
14. Power cord entry

Packing List
02
Creator 3 Pro Filament Quick Start Guide After-sales
service card
Power cord
Unclogging pin tool
Lubricating grease PVP glue stick
Stamping wrench Cross screwdriver
Allen wrench
USB disk Leveling card
PTFE tube
Scraper
快速启动指南
Creator 3 Pro 金刚狼3 Pro
Quick Start Guide
EN/CN/DE/FR/한-A01
本手册仅适用于闪铸科技 金刚狼3 Pro 3D打印机
This guide is only applicable to FLASHFORGE Creator 3 Pro 3D printer
EN P01 / CN P09 / D E P17 / FR P2 5 / 한 P33
WARNING
注意事项
1. Hot! Avoid touching the heating nozzle and heating build plate in
operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。

03
Precautions for Unpacking the Equipment
4. Remove the buckles on the X-axis and Y-axis synchronous belts.
1. Take out the top accessories and pearl cotton.
2. Remove the tape from the machine.
3. Take out the internal pearl cotton block.
6. Press and hold [Z-] continuously until the build plate rises to a higher position, and
then take out the foam block below.
5. Connect the printer to the power supply, after power on, and then click [Tools] and
[Manual] in turn on the touch screen to enter the manual control interface.

04
1. Open the filament holder cover.
2. Take out the filament and insert it
into the filament feeding inlet.
Filament
intake
3. Attention: To facilitate smooth rotation of the filament, please install the filament in
the direction shown in the figure.
When installing the left-side filament, please make it run in the counterclockwise
direction;
When installing the right-side filament, please make it run in the clockwise direction.
Filament Loading
Preparation for Printing

05
4. Insert the filament into the filament
feeding inlet continuously until the filament
goes through the filament guide tube.
5. Press the filament feeding pressing plate
in front of the extruder, insert the filament
vertically into the extruder until it can't be
inserted any further, and then loosen the
filament feeding pressing plate.
6. Insert the filament guide tube into the
filament inlet hole on the extruder to fix.
7. Finally, fix the filament spool on the
filament spool holder and close the cover.

06
8. Filament feeding operation: Click the [Tools]-[Filament] button on the screen in turn,
and set a reasonable heating temperature according to the required temperature value
of the material; Operate according to the screen prompts, and wait for the nozzle to
extrude uniform filament smoothly.
Filament unloading operation: Click [Unload], press down the filament pressing plate
after the extruder temperature heating is completed, pull out the white filament guide
tube, and pull out the filament upward quickly and then filament unloading is completed.
Push filament
down through
for 3 seconds
Withdraw
Filament
Guidetube
Press here

07
9-point leveling function: when the printing flatness is still poor after the platform
leveling and XY/Z axis calibration, this function can be used to compensate for better
flatness;
Manual leveling mode: Execute platform leveling, Z-axis calibration and X, Y axis
calibration in turn. This is a complete set of leveling and calibration operation procedures.
The equipment has been leveled and calibrated before leaving factory. However, the
leveling plane may be damaged due to the vibration generated during transportation. It
is recommended to perform leveling before the first printing. There are two leveling
modes: auxiliary leveling mode and manual leveling mode. In the auxiliary leveling
mode, all execution will be completed with the help of the extruder sensor and auxiliary
prompts. When the function option is in the manual mode, the platform leveling in the
auxiliary mode will not activate the sensor function.
In total, the equipment contains the following leveling calibrations: Platform Leveling,
Calibration XY, Calibration Z and Auto level;
Please operate in the following order:
1. Click [Tools] and [Level Calibration] on the touch screen;
2. Select the auxiliary mode for leveling and calibration;
3. The extruder sensor calibration has been set before leaving factory, so there is no need
to operate again; Click platform leveling and operate following the prompts on the
screen;
4. Perform Z-axis calibration and operate following the prompts on the screen;
5. The X, Y axis have been calibrated before leaving factory, so there is no need to
operate again;
6. The whole leveling and calibration is completed.
Leveling and Calibration

08
Before the first printing, please complete the leveling, loading and calibration correctly
under the guidance of the quick start guide.
1. Tap [Print]. 2. Tap [Local memory] to choose print files.
3. Choose the preset print file [pavilion.gx].
5. The printer starts to heat up and will start printing after heating completed.
First Print
4. Tap [Print].

09
金刚狼3 Pro 快速启动指南
整机介绍
3
4
10
12 13 14
11
5
6
7
8
9
21
1、触摸屏
2、U盘端口
3、右喷头
4、左喷头
5、喷嘴刷
6、打印平台
7、调平螺母
8、丝盘盖
9、丝盘盖把手
10、导风嘴
11、喷嘴
12、以太网接口
13、电源开关
14、电源线接口

10
3D打印机
电源线
通 针
润滑脂 PVP固体胶
冲压扳手 十字螺丝刀
内六角扳手
U盘 调平卡
聚四氟乙烯管
3D打印耗材 快速启动指南 售后服务卡
铲 刀
装箱清单
快速启动指南
Creator 3 Pro 金刚狼3 Pro
Quick Start Guide
EN/CN/DE/FR/한-A01
本手册仅适用于闪铸科技 金刚狼3 Pro 3D打印机
This guide is only applicable to FLASHFORGE Creator 3 Pro 3D printer
EN P01 / CN P09 / D E P17 / FR P2 5 / 한 P33
WARNING
注意事项
1. Hot! Avoid touching the heating nozzle and heating build plate in
operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。

11
4. 移除X轴、Y轴同步带上的卡扣；
1. 取出顶部配件与珍珠棉；
2. 移除机身上的胶带；
3. 取出内部的珍珠棉块；
6. 持续按住【Z-】，直到打印平台上升到较高的位置，取出下方的泡沫块。
5. 打印机连接电源，开机后，在触摸屏上依次点击【工具】、【手动调节】进入手动控制界面；
设备开箱的注意事项

12
1. 打开丝盘盖。
2. 取出耗材，将耗材插入进丝口中。
进丝口
3. 注意：为方便耗材转动顺畅，请按图中所示的方向安装耗材。
安装左侧耗材时，请按逆时针方向出丝；安装右侧耗材时，请按顺时针方向出丝。
安装丝料
打印前准备

13
4. 持续将耗材送入进丝口，直到耗材从导丝管
穿出。
5. 按下喷头前方的进丝压板，将耗材垂直插入
喷头，直到无法继续插入。松开进丝压板。
6. 将导丝管插入喷头进丝孔中固定。
7. 最后将丝盘固定在丝盘架上，盖上丝盘盖。

14
8. 进丝操作：点击屏幕中的【工具】-【换丝】按钮，根据材料所需温度值设置合理加热温度；根
据屏幕提示进行操作，等待喷嘴挤出均匀的耗材。
退丝操作：点击【退丝】，待喷头温度加温完成后，向下压耗材压板，拔出白色耗材导丝管，将耗
材迅速向上拔出，退丝完成。
向下按压
耗材3秒
拔出导丝管

15
9点调平功能：在平台调平以及XY/Z轴校准后，打印平面度仍较差时，可以使用该功能进行补偿，
以获得更好的平面度；
手动调平模式：依次执行平台调平、Z轴校准、XY轴校准。此为一套完整的调平校准操作流程。
设备出厂已进行过调平校准，由于运输中会产生震动，调平面可能会被破坏，建议首次打印前进行
一次调平。调平方式有两种模式：辅助调平模式和手动调平模式。在辅助调平模式下，所有执行将
借助喷头传感器及辅助提示完成。
当功能选项在手动模式时，辅助模式中的平台调平将不启动传感器功能。
设备总共包含如下调平校准：平台调平，XY校准，Z轴校准，9点调平；
按如下顺序进行操作：
1. 在触控屏上点击【工具】、【调平与校准】；
2. 选择辅助模式进行调平校准；
3. 喷头传感器校准已在出厂前完成设定，无需再操作；点击平台调平，按照屏幕指示进行操作；
4. 进行Z轴校准，按屏幕提示进行操作；
5. X.Y轴在出厂前已经完成校准，无需再操作；
6. 整个调平校准完成。
调平与校准

16
首次打印前，请在快启的指引下正确地完成调平、进丝和校准。
1. 打印开始前请确保打印机已经经过调平；
2. 打印开始前确保耗材安装正确，没有打结或卡住；
3. 喷头内可能残留有少量耗材，请进丝一段时间，确保上一次打印的耗材已经全部挤出;
4. 使用ABS耗材打印时，请装上顶罩，关闭前门；使用PLA耗材打印时，请移除顶罩，打开前门;
5. 打印开始前请将喷头耗材清理干净;
6. 不可在长时间无人看守的情况下使用3D打印机。
打印建议
1. 点击 [打印]。 2. 点击 [内部储存] 进入打印模型选择界面。
5. 打印机开始加热，加热完成后开始打印。
首次打印
3. 选择预设文件 [pavilion.gx]. 4. 点击 [打印]。

17
Creator 3 Pro Kurzanleitung
Vorstellung von Creator 3 Pro
3
4
10
12 13 14
11
5
6
7
8
9
21
1. Touchscreen
2. USB-Anschluss
3. Rechter Extruder
4. Linker Extruder
5. Düsenbürste
6. Konstruktionsplattform
7. Nivelliermutter
8. Filamenthalterabdeckung
9. Griff der Fadenabdeckung
10. Führungsnase
11. Düse
12. Ethernet-Anschluss
13. Netzschalter
14. Stromkabelanschluss

18
Creator 3 Pro
Stromkabel
Reinigungsstift-
werkzeug
Schmierfett PVP-Leimstift
Stanzschlüssel Kreuzschrauben-
dreher
USB-Disk Nivellierkarte
PTFE-Rohr
Filament Kurzanleitung Kundendienstkarte
Abstreifer
Innensechs-
kantschlüssel
Verpackungsinhalt
快速启动指南
Creator 3 Pro 金刚狼3 Pro
Quick Start Guide
EN/CN/DE/FR/한-A01
本手册仅适用于闪铸科技 金刚狼3 Pro 3D打印机
This guide is only applicable to FLASHFORGE Creator 3 Pro 3D printer
EN P01 / CN P09 / D E P17 / FR P2 5 / 한 P33
WARNING
注意事项
1. Hot! Avoid touching the heating nozzle and heating build plate in
operation.
2. Moving parts in printer may cause injury. Do not wear gloves or other
sources of entanglement in operation.
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。