Flashforge Inventor II User manual

1. Hot! Avoid touching the heating nozzle and heatingbuild platein operation.
Please refer to FlashForge official website www.flashforge.com to download
the newest User's Guide, Software and Instruction Videos.
(Support-Support Center-Select a Product)
2. Moving parts inprintermaycause injury. Do not wear gloves or other
sources of entanglement in operation.
Download
1. 高温危险！打印机喷嘴和打印平台在工作时会被加热，请避免接触!
2. 可动部件可能造成卷入挤压和切割伤害。操作机器时请不要佩戴手套或缠绕物。
前往闪铸科技官方网站 www.sz3dp.com ，可以在[ 技术支持 ] 页面下载用户使
用手册、切片软件等资料，或查看相关操作视频。
资料下载
快速启动指南
Quick Start Guide
SZ15-ZN/EN-A04
中文

Grease / Allen Wrench
01

10. Leveling Knob
02

1. Take out the packing box, which contains a
Quick Start Guide, a After-sales Service Card,
a power adapter, a power cable, a solid glue,
a filament guide tube, a tool bag with an USB
stick inside.
03

04

5. Connect power adapter with the power cable and then insert the power supply into the power
input on the back of the Inventer II. Turn on the power switch and press the touch screen button
to turn on the printer.
05

1. Tap [Tools]-[Level] on your InventorII touch screen. Please wait while the extruder and platform
finish initial movements. Screw three nuts under the platform counterclockwise, then tap [OK]
button.
Screw the three nuts under the platform
counterclockwise until they are tight,
then tap the [OK] button.
06

2. After tapping [OK] button, the extruder will move towards the first point and the plate will move
up and down to verify the distance between nozzle and plate.
3. If the distance between the nozzle and plate is too big, rotate the nut underneath the platform
clockwise until you hear a steady beep. If the distance is too small, rotate the nut counterclockwise
until you hear a steady beep.
Turn the corresponding nut under
the platform clockwise until
you hear the beep.
Turn the corresponding nut under
the platform counterclockwise until
you hear the beep.
07

1. Tap [Preheat]--[Start] to heat up the extruder.
2. Once preheated, hold down the spring presser and pull out the filament.
3. Tap the return button, insert the new filament into the filament intake, tap [Tools]-[Filament]-
[Load]. The filament will be drawn through the extruder once heated. Wait for the extruder to
provide a steady flow of filament.
08

09

润滑脂 / 内六角扳手
10

触摸屏
电源线接口
触摸屏开关
11

1. 打开纸箱取出中间的包装盒，上方自封袋内
有快速启动指南和售后服务卡，盒内含有电
源线、USB线、电源适配器、工具包（内有
U盘等工具）、固体胶和导丝管。
12

10. 用手托住打印平台，缓缓将其提升，
以便于取出平台下方的泡沫盒。
13

14

请逆时针拧紧底板下三个螺母
再点击【确定】按钮。
1. 点击触摸屏上【工具】－【调平】图标，待喷头和打印平台完成初始化运动后逆时针拧紧底板
下三个螺母，再点击【确认】按钮。
15

2. 喷头开始移向第一个点，打印平台上下移动来验证喷嘴与平台之间的距离。
顺时针调节平台下对应的螺母
直到听到持续稳定的提示声。
逆时针调节平台下对应的螺母
直到听到持续稳定的提示声。
16

17

18