Flashforge Guider 2 User manual

SZ11S-ZN/EN-A02 Guider 2 / Guider 2s
引领者 2 / 引领者 2s
This guide is only applicable to FLASHFORGE Guider 2/Guider 2s 3D printer
P14
本指南仅适用于闪铸科技 引领者2/引领者2s 3D打印机

01
3. The bottom PE foam should contain: a spool of
PLA filament, a spool holder, a solid glue, a USB
cable, a filament guide tube and a accessories
bag.
5. Remove the top PE foam piece, which
contains one power cable, one USB Stick,
one Quick start guide and a After-sales
service card.
2. Take your 3D printer out of the box.

9. Tap [Tools].
Build
Power Switch
12. Remove both bottom foam pieces. Tear off
the stretch wrap.
11. Tap [Z-] to partially elevate the build plate.
Tap touch screen button on the right side of
touch screen, go back to home screen.
7. Tear off tape and the stretch wrap of front door.
Squeeze top lid slightly from both sides to the
middle so as to take top lid successfully.
Remove the stretch wrap of top lid.
Tear off the
stretch wrap
02

03

3. Y-Axis Guide Rod 4. X-Axis Guide Rod1. Z-Axis Guide Rod 2. Filament Intake
7. Build Plate 8. Nut5. Touch Screen 6. Touch Screen Button
11. Nozzle 12. Turbo Fan Baffle9. Servo 10. Turbo Fan
15. USB Cable Input 16. Spool Holder Slot13. Network Interface 14. USB Stick Input
17. Power Switch 18. Power Input
04
Getting to Know Your Guider 2

3. Air-Filter 4. Y-Axis Guide Rod1. Z-Axis Guide Rod 2. Filament Intake
7. Touch Screen Button 8. Build Plate5. X-Axis Guide Rod 6. Touch Screen
11. Servo 12. Turbo Fan9. Nut 10. Camera
(Inside the printer)
15. Network Interface 16. USB Stick Input13. Nozzle 14. Turbo Fan Baffle
17. USB Cable Input 18. Spool Holder Slot 19. Power Switch 20. Power Input
05
Getting to Know Your Guider 2S

5. After filament goes through guide tube, press
spring presser on the left side of extruder, and
insert filament vertically into filament intake.
1. Locate the spool holder. Install the spool holder
into the left quadrangular opening on the back.
6. After inserting into filament intake, insert guide
tube into extruder filament intake to fix.
Press here Filament intake
06

How to use the nuts
Rotate the nuts clockwise
Raise the build plate to reduce the distance
between the nozzle and build plate.
Lower the build plate to increase the distance
between the nozzle and build plate.
Rotate the nuts Anticlockwise
Build plate goes up
Build plate goes down
Leveling Build Plate
1. Tap [Tools].
Build
2. Tap [Level].
07
Berfore leveling, let's learn the funciton of nuts.
0403
0201
Tools

7. If the distance is appropriate, tap [ok] to next
step. If the diastance still not appropriate, please
follow the prompts on the touch screen to
adjust till you see [ok].
Tap the [OK] button to move to
the next leveling point.
Congartulations
Screw the three nuts under the platform
counterclockwise until they are tight,
then tap the [OK] button.
3. Please wait while the extruder and platform finish initial movements. Screw three nuts under the
platform anticlockwise, then tap [OK] button.
Attention: three nuts may be tightened up before going out, please skip this step if you find
three nuts have been tightened up, and continue to following steps
4. After tapping [OK] button, the extruder will
move towards the first point and the plate will
move up and down to verify the distance
between nozzle and plate.
6. Then tap the [Verify] button to check whether
the distance is appropriate.
5. If the distance between the nozzle and plate
is too large, rotate the three nuts underneath
the platform clockwise for the same rounds
until you hear a steady beep.
08

09
8. After first leveling point completed, start the other two leveling points.
Attention: when starting the second and the third leveling points, just need to adjust one
corresponding nut under extruder.
9. Follow the prompts on the touch screen to adjust the corresponding nut till you hear a steady
beep.
Turn the corresponding nut under
the platform clockwise until
you hear the beep.
Distance Too Small
Turn the corresponding nut under
the platform anticlockwise until
you hear the beep.
10. If the distance is appropriate, tap [ok] to next
step. If the diastance still not appropriate,
please follow the prompts on the touch
screen to adjust till you see [ok].
11. Start the third leveling point according to the
method of the second leveling point.
After leveling completed, tap return arrow to
go back to home screen.
Tap the [OK] button to move to
the next leveling point.
Congartulations
Leveling completed!
Finish

Loading Filament
1. Tap [Tools]. 2. Tap [Filament].
3. Tap [Load], extruder starts to heat.
4. Once heated, filament will be drawn through the extruder. Continue extruding until the extruder
provides a steady flow of filament. Tap touch screen button, go back to home screen.
Done
Loading started, push filament vertically
into extruder and press [Done] when you see
filament come out of the extruder
10
Attetion: If extruder can not unload in a long time, please check if you have inserted filament
into the bottom of extruder.

1. Please insert the USB stick into USB stick
input on the right side of the printer. Tap [Build].
2. Tap [USB Stick]. 3. Tap [Test Files].
5. Tap [Build].
6. The printer starts to heat and it prints
automatically after heating completed.
4. Tap [40mm_Box-PLA.gx].
Quick Start Guide 快启
Test Files 测试文件
User Guide 说明书
Flashprint切片软件
PLA
PLA
11
1. Ensure that the build plate has been leveled before
printing.
2. Ensure that the filament has been loaded in an
appropriate approach.
3. Load the filament for a while to extrude all the
melted filament you printed last time out of the
extruder.
4. Please clean extruder before printing.
5. Do not leave the printer unattended during
operation.

Extruder
Load Unload
Done
Extruder
Unload started, press down on the
spring lever and withdraw filament
2. Tap [Tools].
Please follow steps below if you need to unload filament in
daily use.
3. Tap [Filament]. 4. Tap [Unload].
Unloading Filament
12
1. Pull filament guide tube out of filament intake,
leave filament 10cm to pull filament easily.
Press here
Push filament down through for 3 seconds
5. When heating to target temparture, press
spring presser and push filament down through
for 3 seconds, until you see steady filament
coming out from nozzle.

13
Press here Withdraw
Filament
6. Then pull out vertically quickly and release spring presser.
Tap [Done], go back. Tap return arrow to go back to home screen.

14
3. 在纸箱底部的泡沫块中包含有一卷耗材、
丝盘轴、固体胶、USB线、耗材导丝管和
工具包。
2. 将打印机从纸箱中提出。
5. 移除打印机顶部泡沫块，上面附带有一根电
源线、一个U盘、一本《快速启动指南》和
一张《售后服务卡》。撕除固定前门的无痕
胶带。

7. 撕保护前门的无痕胶带和缠绕膜。轻轻从两
侧向中间挤压顶罩，以便顺利取出顶罩。
撕除包裹顶罩的缠绕膜。
8. 取出电源线，插入打印机背部的电源接口，
按下图中箭头所示的电源开关，接通电源。
9. 开机后在液晶屏上点击[Tools]。
12. 取出下方的两块泡沫块，撕除固定打印
平台的缠绕膜。
11. 按住“Z-”将打印平台上升至机身中部。
点击触摸屏右侧的开关返回主界面。
Build
电源开关
撕除此处
的缠绕膜
15

16

1. Z轴导轨 2. 喷头进丝孔 3. Y轴导轨 4. X轴导轨 5. 触摸屏
6. 开关 7. 打印平台 8. 调平螺母 9. 调平舵机 10. 涡轮风扇
11. 喷嘴 12. 导风嘴 13. 网线接口 14. U盘接口 15. USB线接口
16. 丝盘轴插口 17. 电源开关 18. 电源线接口
引领者2 部件介绍
17

1. Z轴导轨 2. 喷头进丝孔 3. 空气过滤装置 4. Y轴导轨 5. X轴导轨
6. 触摸屏 7. 开关 8. 打印平台 9. 调平螺母 10. 摄像头(打印机内侧)
11. 调平舵机 12. 涡轮风扇 13. 喷嘴 14. 导风嘴 15. 网线接口
16. U盘接口 17. USB线接口 18. 丝盘轴插口 19. 电源开关 20. 电源线接口
引领者2s 部件介绍
18

2. 丝盘轴插入丝盘轴插口后，让丝盘轴底部向下
贴住打印机背部。
5. 耗材穿过导丝管后，按下喷头左侧的压板，
然后将耗材垂直插入喷头进丝孔中，直到
耗材无法继续插入。
6. 耗材插入进丝孔后，再将导丝管插入喷头进丝
孔固定。
按下压板
进丝孔
19