Flashforge Inventor 2 User manual

SZ15-ZN/EN-A07
P15
Inventor 2 / Inventor 2s
发明家 2 / 发明家 2s
This guide is only applicable to FLASHFORGE Inventor II / Inventor IIs 3D printer
本指南仅适用于闪铸科技 发明家II/发明家IIs 3D打印机

01
1. Take out the packing box, which contains a
Quick Start Guide, an After-sales Service Card,
a power adapter, a power cable, a solid glue,
a filament guide tube, a tool bag with an USB
stick inside.
2. Take out the 3D printer.
3. Check filament inside the box. 4. Remove all protective foams.
5. Remove the tape and the packing bag. 6. Remove the top foam piece.

02
8. Open the door, squeeze top lid slightly from
both sides to the middle so as to take top lid
successfully.
7. Use scissors to cut the ties that hold the
rods in the place.

Allen Wrench
Grease
03
Inventor 2 Kit Contents

04
Allen Wrench
Fan Grease
Inventor 2s Kit Contents

10. Nut
05
Getting to Know Your Inventor 2

06
11. Nut
Getting to Know Your Inventor 2s

07
Filament Outlet
Filament Guide Tube
Please pay attention to
loading direction!
4. After filament goes through guide tube, press
spring presser on the left side of extruder, and
insert filament vertically into filament intake to
the bottom.
1. Filament cartridge is at the back of printer. Before taking out filament cartridge, please hold the
clip on the top and take filament cartridge out.
2. Take out filament, tear off vacuum packing and put it into filament cartridge. Put filament through
filament outlet as the picture shown on the top left.
3. Hold clip on the top of filament cartridge, put
filament catridge back to the printer, and put
filament through filament guide tube.
Attention: filament unwinding direction should keep pace with the picture, or causing cannot
print properly.
Press here Filament intake

5. After inserting into filament intake, insert
guidetube into extruder filament intake.
6. Finally put the other end of filament guidetube
to filament outlet on the top of filament
cartridge.
7. Connect the power adapter with the power cable. 8. Insert the power supply into the power input
on the back.
10. Press the touch screen button to turn on
the printer.
Touch Screen Button
9. Plug the other end of power cable into socket,
turn on the power switch.
08

04
How to use the leveling nuts
Rotate the nut clockwise
Raise the build plate to reduce the distance
between the nozzle and build plate.
Lower the build plate to increase the distance
between the nozzle and build plate.
Rotate the nut Anticlockwise
Build plate goes up Build plate goes down
Berfore leveling, let's learn the funciton of leveling nuts.
1. Tap [Tools]. 2. Tap [Level].
02
03
01
09

Attention: three nuts may be tightened up before going out, please skip this step if you find
three nuts have been tightened up, and continue to following steps
3. After tapping [OK] button, the extruder will
move towards the first point and the plate will
move up and down to verify the distance
between nozzle and plate.
5. After tapping [OK] button, the extruder will
move towards the first point and the plate will
move up and down to verify the distance
between nozzle and plate.
4. If the distance between the nozzle and plate
is too large, rotate three nuts underneath
the platform clockwise for the same rounds
until you hear a steady beep.
6. If the distance is appropriate, tap [ok] to next
step. If the diastance still not appropriate,
please follow the prompts on the touch screen
to adjust till you see [ok].
2. Please wait while the extruder and platform finish initial movements. Screw three nuts under the
platform anticlockwise, then tap [OK] button.
Screw the three nuts under the platform
counterclockwise until they are tight,
then tap the [OK] button.
Turn all three nuts under the platform
clockwise equally until
you hear the beep.
10

11
8. After first leveling point completed, start the other two leveling points.
Attention: when starting the second and the third leveling points, just need to adjust one
corresponding nut under extruder.
10. If the distance is appropriate, tap [ok] to next
step. If the diastance still not appropriate,
please follow the prompts on the touch
screen to adjust till you see [ok].
11. Start the third leveling point according to the
method of the second leveling point.
After leveling completed, tap return arrow to
go back to home screen.
9. Follow the prompts on the touch screen to adjust the corresponding nut till you hear a steady
beep.
Turn the corresponding nut under
the platform clockwise until
you hear the beep.
Turn the corresponding nut under
the platform counterclockwise until
you hear the beep.
Leveling completed!
Finish

12
2. Tap [Load]. 3. Extruder starts to heat.
Attetion: If extruder can not unload in a long time, please check if you have inserted filament
into the bottom of extruder.
4. Once heated, filament will be drawn through the extruder. Continue extruding until the extruder
provides a steady flow of filament.
Loading started, push filament vertically
into extruder and press [Done] when you see
filament come out of the extruder
Loading Filament
Finish

13
1. Insert USB stick into the USB stick input.
In print interface, tap [Build]-[USB stick].
1. Ensure that the build plate has been leveled before
printing.
2. Ensure that the filament has been loaded in an
appropriate approach.
3. Load the filament for a while to extrude all the
melted filament you printed last time out of the
extruder.
4. Please clean extruder before printing.
5. Do not leave the printer unattended during
operation.
Polar Cloud Print
Polar Cloud Disconnected
FlashPrint切片软件
Quick Start Guide快启
Test Files测试文件
Software Installation Packa..
Happy3D软件安装包
Internal Storage
USB Stick
P

14
Extruder
Unload started, press down on the
spring lever and withdraw filament
2. Tap [Tools].1. Pull filament guide tube out of filament intake,
leave filament 10cm to pull filament easily.
Please follow steps below if you need to unload filament in
daily use.
3. Tap [Filament]. 4. Tap [Unload].
Unloading Filament
Press here
Push filament down
through for
3 seconds
Withdraw
filament
Press here
Done
5. When heating to target temparture, press
spring presser and push filament down through
for 3 seconds, until you see steady filament
coming out from nozzle.
6. Then pull out vertically quickly and release
spring presser. Tap [Finish], go back. Tap return
arrow to go back to home screen.

15
1. 打开纸箱取出中间的包装盒，上方自封袋内
有快速启动指南和售后服务卡，盒内含有电
源线、USB线、电源适配器、工具包（内有
U盘等工具）、固体胶和导丝管。
5. 撕除打印机两侧和底部的胶带，去除包装袋。
4. 去除在运输中起保护作用的泡沫。
2. 取出打印机。
3. 注意纸箱底部有一卷耗材。

16
10. 用手托住打印平台，缓缓将其提升，
以便于取出平台下方的泡沫盒。
8. 轻轻地向中间挤压顶罩两侧，以便顺利取出。

17
内六角扳手
润滑脂
发明家 2 装箱物品

18
内六角扳手
风 扇 润滑脂
发明家 2s 装箱物品