FLIR DCV64DL User manual

Product Information
User Manuals Quick Start Guides
Specification Sheets
WARNING - A REGULATED UL / CSA APPROVED 12V DC / 24V AC
power supply is REQUIRED for use with this camera. Use of a non-
regulated, non-conforming power supply can damage this product and
voids the warranty.
Video Tutorials & DemosLatest News
1 x Flat-head Screwdriver
Contents
700+ TVL
VARIFOCAL IR DOME CAMERA
MODEL: DCV64DL
QUICK START GUIDE
English Version 2.0
www.digimerge.com
IT’S ALL ON THE WEB!
www.digimerge.com
VISIT
Digimerge Technologies Inc.
Copyright © 2013
As our products are subject to continuous improvement, Digimerge
reserves the right to modify product design, specifications and prices,
without notice and without incurring any obligation. E&OE
1 x Weatherproof IR Dome
Camera with Varifocal Lens
4 x Mounting Screws
Features
Safety Precautions
• Use an appropriate low voltage power cable to prevent
fire or electrical shock.
• Make sure to install the camera in an area that can
support the camera weight.
• There are no user serviceable parts inside the camera.
Please do not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens cover.
Ultra Resolution,
Outstanding Value Cameras
Ultra Resolution Cameras
with Advanced Features
Fully Connected DVR’s
• 1/3” Sony EX-View II 960H with Effio DSP/700+ TVL
• Superior Low Light Sensitivity
• Advanced Digital Noise Reduction
• Smart IR Night Vision (100ft/31m)*
• 2.8–10.5mm Varifocal Auto Iris Lens
• External Zoom/Focus Adjustment
• IP66 Weatherproof Rating**
• 3-Axis Design for Wall/Ceiling Mounting
• Vandal Resistant
• 12V DC/24V AC Operation
* IR Illumination range under ideal conditions. Objects at or beyond
this range may be partially or completely obscured, depending on the
camera application
** Not recommended for submersion in water

Camera Base
FOCUS ZOOM
Installing the Camera
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the camera(s) and
cables to the DVR.
Image Sensor 1/3” Sony EX-View™ II 960H
Video Format NTSC
Effective Pixels H: 976 V: 494
Horizontal Resolution 700+ TVL
Scan System 2:1 Interlace
Sync System Internal
S / N Ratio >52dB (AGC Off)
Iris Auto Iris
AES Shutter Speed 1/60 ~ 1/100,000 sec.
Min. Illumination 0.03 LUX @ F1.2 (IR Off)
0 LUX (IR LEDs ON)
Video Output Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type 2.8–10.5mm F1.6 / Varifocal AI
FOV (Diagonal) 38–104°
Termination Video: BNC Female
IR Range / Qty. 100ft / 31m; 35 LED’s
Power Requirement 12V DC ± 10% / 24V AC ± 10%
Power Consumption 12V: 650mA max / 24V: 325mA max
Operating Temp. Range –4° ~ 122°F / –20° ~ 50°C
Environmental Rating IP66
Dimensions (LxWxH) 4.8” x 4.8” x 4.1”
119mm x 119mm x 80mm
Weight (including stand) 1.4lbs / 0.6kg
Dimensions
Camera SpecificationsSetting up the Camera
1. Connect the BNC connector of the camera
to the video cable.
2. Connect power source to the power
terminal block.
NOTE: Make sure to follow correct polarity as marked on the
power connector. For AC power, connect multiple cameras
using consistent wiring polarity to prevent video rolling.
1. Rotate the camera base counter
clockwise to separate it from the ball
camera and dome cover.
2. Mount the camera base to the wall or
ceiling using the included screws.
3. Feed the BNC/power termination cable
through the camera base. Connect
video and power cable as described
in the next section, ‘Setting up the
Camera’.
4. Position the dome cover over the
camera and screw it clockwise half way
onto the camera base.
5. Move the ball camera to the desired
position, and while holding the ball
camera firmly in place, screw the dome
cover the rest of the way to secure it to
the camera base. Holding the camera
prevents it from moving while installing
the dome cover. 119mm / 4.7”
80mm
3.1”
3. Use a screwdriver to adjust the ZOOM and
FOCUS control screws as required.
Video connector
Power terminal block
(pre-attached)
Power connector