FLIR Quasar CM-6405 User manual

This document does not contain any export-controlled information.
Quasar™ Mini-Dome
Installation and
User Guide
CM-6405/CM-6408
i
CM-640x Installation and User Guide - Revision 100 - December 2020

This document does not contain any export-controlled information.
© 2020 FLIR Systems, Inc. All rights reserved. No parts of this material may be copied, translated, or transmitted (in
any medium) without the prior written permission of FLIR Systems, Inc.
Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems,
Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are used for
identification only and are the property of their respective owners.
Protected by one or more patents and patent applications. Learn more here: www.flir.com/patentnotice.
Photographs and images appearing in this manual may have been modified for illustrative purposes using commercial
image editing software and may not always reflect an actual product configuration. The contents of this document are
subject to change without notice.
For additional information visit www.flir.com or write to:
FLIR Systems, Inc.
6769 Hollister Avenue
Goleta, CA 93117
USA
Support: https://www.flir.com/support/
[e-mail]
Important Instructions and Notices to the User:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Modification of this device without the express authorization of FLIR Systems, Inc. may void the user’s authority under
FCC rules to operate this device.
Proper Disposal of Electrical and Electronic Equipment (EEE)
The European Union (EU) has enacted Waste Electrical and Electronic Equipment Directive
2012/19/EU (WEEE), which aims to prevent EEE waste from arising; to encourage reuse,
recycling, and recovery of EEE waste; and to promote environmental responsibility.
In accordance with these regulations, all EEE products labeled with the “crossed out wheeled bin”
either on the product itself or in the product literature must not be disposed of in regular rubbish
bins, mixed with regular household or other commercial waste, or by other regular municipal
waste collection means. Instead, and in order to prevent possible harm to the environment or
human health, all EEE products (including any cables that came with the product) should be
responsibly discarded or recycled.
To identify a responsible disposal method nearby, please contact the local waste collection or
recycling service, the original place of purchase or product supplier, or the responsible
government authority in the area. Business users should contact their supplier or refer to their
purchase contract.
Document History
Revision
Date
Comment
100
December 2020
Initial FLIR release
CM-640x Installation and User Guide - Revision 100 - December 2020 ii

This document does not contain any export-controlled information.
Register your Product with FLIR at https://customer.flir.com.
For warranty information, see https://www.flir.com/support-center/warranty/security/flir-security-product-
warranties/.
Product Registration and Warranty
Information
iii
CM-640x Installation and User Guide - Revision 100 - December 2020

This document does not contain any export-controlled information.
Table of Contents
iv
CM-640x Installation and User Guide - Revision 100 - December 2020
1. Document Scope and Purpose .................................................................................................. 1
2. Camera Overview ........................................................................................................................ 4
Features ............................................................................................................................... 4
2.1
Accessing Product Information from the FLIR Website ...................................................... 5
2.2
Camera Dimensions ............................................................................................................ 6
2.3
3. Installation ................................................................................................................................... 7
Preparation .......................................................................................................................... 7
3.1
Supplied Components ........................................................................................... 7
3.1.1
Site Preparation - General ..................................................................................... 8
3.1.2
Indoor Mounting ..................................................................................................... 9
3.1.3
Outdoor Mounting .................................................................................................. 9
3.1.4
Pre-Installation Checklist ....................................................................................... 9
3.1.5
Power Supply Options ......................................................................................... 10
3.1.6
Initial Configuration ............................................................................................................ 11
3.2
Remove Dome Cover and Separate Base from Mounting Bracket ..................... 12
3.2.1
Connect the Camera ............................................................................................ 13
3.2.2
Configure for Networking ..................................................................................... 15
3.2.3
Change Video Format (Optional) ......................................................................... 16
3.2.4
Re-attach Dome Cover ........................................................................................ 17
3.2.5
Mounting and Connecting the Camera .............................................................................. 18
3.3
Fit Mounting Hardware ........................................................................................ 18
3.3.1
Remove Dome Cover and Separate Base from Mounting Bracket ..................... 18
3.3.2
Install Mounting Bracket ...................................................................................... 18
3.3.3
Route Cables and Connect the Camera .............................................................. 18
3.3.4
Mount and Aim the Camera ................................................................................. 19
3.3.5
Additional Configuration Steps .......................................................................................... 20
3.4
Attaching the Camera to a Supported VMS ...................................................................... 22
3.5
4. Operation and Configuration ................................................................................................... 23
Accessing the Camera's Web Page .................................................................................. 23
4.1
Camera Web Page Introduction ........................................................................................ 26
4.2
Live Screen ........................................................................................................................ 27
4.3
System Tab ........................................................................................................................ 30
4.4
System ................................................................................................................. 31
4.4.1
Security ................................................................................................................ 32
4.4.2
User ........................................................................................................................... 32
4.4.2.1
HTTPS ....................................................................................................................... 34
4.4.2.2

This document does not contain any export-controlled information.
Table of Contents
v
CM-640x Installation and User Guide - Revision 100 - December 2020
IP Filter ...................................................................................................................... 37
4.4.2.3
IEEE 802.1X .............................................................................................................. 38
4.4.2.4
Network ................................................................................................................ 39
4.4.3
Basic .......................................................................................................................... 39
4.4.3.1
QoS ............................................................................................................................ 41
4.4.3.2
VLAN ......................................................................................................................... 42
4.4.3.3
SNMP ....................................................................................................................... 43
4.4.3.4
UPnP ......................................................................................................................... 44
4.4.3.5
DDNS ......................................................................................................................... 45
4.4.3.6
Mail ............................................................................................................................ 46
4.4.3.7
FTP ............................................................................................................................ 47
4.4.3.8
HTTP ......................................................................................................................... 48
4.4.3.9
Events Setup ........................................................................................................ 49
4.4.4
IO ............................................................................................................................... 49
4.4.4.1
Network Failure Detection .......................................................................................... 50
4.4.4.2
Tampering .................................................................................................................. 51
4.4.4.3
Periodic Event ............................................................................................................ 54
4.4.4.4
Manual Trigger ........................................................................................................... 55
4.4.4.5
Audio Detection .......................................................................................................... 56
4.4.4.6
Triggered Actions ....................................................................................................... 58
4.4.4.7
Edge Recording ................................................................................................... 60
4.4.5
SD Card ..................................................................................................................... 61
4.4.5.1
Network Share ........................................................................................................... 62
4.4.5.2
Recording .................................................................................................................. 65
4.4.5.3
Motion Detection .................................................................................................. 66
4.4.6
Schedule .............................................................................................................. 68
4.4.7
File Location ......................................................................................................... 69
4.4.8
Maintenance ........................................................................................................ 69
4.4.9
Log File ...................................................................................................................... 70
4.4.9.1
User Information ........................................................................................................ 70
4.4.9.2
Factory Default ........................................................................................................... 70
4.4.9.3
Software Version ........................................................................................................ 72
4.4.9.4
Software Upgrade ...................................................................................................... 72
4.4.9.5
Parameters ................................................................................................................ 74
4.4.9.6
Import/Export ....................................................................................................... 74
4.4.10
Streaming Tab ................................................................................................................... 75
4.5
Video Configuration ............................................................................................. 76
4.5.1

This document does not contain any export-controlled information.
Table of Contents
vi
CM-640x Installation and User Guide - Revision 100 - December 2020
Encode Type .............................................................................................................. 77
4.5.1.1
CM-6408 Video Resolutions ...................................................................................... 79
4.5.1.2
CM-6405 Video Resolutions ...................................................................................... 82
4.5.1.3
Video Rotation ..................................................................................................... 86
4.5.2
Video Text Overlay .............................................................................................. 87
4.5.3
Video OCX Protocol ............................................................................................. 88
4.5.4
Video Mask .......................................................................................................... 89
4.5.5
Audio .................................................................................................................... 89
4.5.6
Camera Tab ....................................................................................................................... 91
4.6
Exposure Screen ................................................................................................. 91
4.6.1
Auto Iris Mode ............................................................................................................ 92
4.6.1.1
P-Iris Priority Mode .................................................................................................... 93
4.6.1.2
Iris Priority Mode ........................................................................................................ 94
4.6.1.3
Auto Shutter Mode ..................................................................................................... 94
4.6.1.4
Shutter Priority Mode ................................................................................................. 94
4.6.1.5
Manual Mode ............................................................................................................. 95
4.6.1.6
Picture Adjustment ............................................................................................... 96
4.6.2
Advanced Picture Settings ................................................................................... 96
4.6.3
White Balance ............................................................................................................ 97
4.6.3.1
Highlight Compensation (HLC) .................................................................................. 98
4.6.3.2
WDR Function ............................................................................................................ 98
4.6.3.3
Noise Reduction Settings ........................................................................................... 98
4.6.3.4
IR Function ........................................................................................................... 99
4.6.4
Misc. Screen ...................................................................................................... 100
4.6.5
Log Out ............................................................................................................................ 101
4.7
5. Appendices .............................................................................................................................. 102
Technical Specifications .................................................................................................. 102
5.1
Internet Security Settings ................................................................................................ 102
5.2
Install UPnP Components ............................................................................................... 104
5.3
Installing and Deleting the Web Player ........................................................................... 106
5.4
Connecting Leads to a Spring Clamp Terminal Block ..................................................... 107
5.5
Deleting Temporary Internet Files ................................................................................... 108
5.6
Troubleshooting ............................................................................................................... 109
5.7
Accessories ..................................................................................................................... 111
5.8

This document does not contain any export-controlled information.
Document Scope and Purpose
1
CM-640x Installation and User Guide - Revision 100 - December 2020
1 Document Scope and Purpose
The purpose of this document is to provide installation, operation, and configuration instructions for
Quasar CM-640x cameras.
Note:
This document is intended for use by technical users who have a basic understanding of CCTV
camera/video equipment and LAN/WAN network connections.
Remarque:
Ce document est destiné aux utilisateurs techniciens qui possèdent des connaissances de base des
équipements vidéo/caméras de télésurveillance et des connexions aux réseaux LAN/WAN.
Warning:
Installation must follow safety, standards, and electrical codes as well as the laws that apply where the
units are being installed.
Avertissement:
L'installation doit respecter les consignes de sécurité, les normes et les codes électriques, ainsi que la
législation en vigueur sur le lieu d'implantation des unités.
Disclaimer
Users of FLIR products accept full
responsibility for ensuring the suitability and
considering the role of the product detection
capabilities and their limitation as they apply
to their unique site requirements.
FLIR Systems, Inc. and its agents make no
guarantees or warranties to the suitability for
the users’ intended use. FLIR Systems, Inc.
accepts no responsibility for improper use or
incomplete security and safety measures.
Failure in part or in whole of the installer,
owner, or user in any way to follow the
prescribed procedures or to heed
WARNINGS and CAUTIONS shall absolve
FLIR and its agents from any resulting liability.
Specifications and information in this guide
are subject to change without notice.
Avis de non-responsabilité
Il incombe aux utilisateurs des produits FLIR de vérifier
que ces produits sont adaptés et d'étudier le rôle des
capacités et limites de détection du produit appliqués
aux exigences uniques de leur site.
FLIR Systems, Inc. et ses agents ne garantissent
d'aucune façon que les produits sont adaptés à l'usage
auquel l'utilisateur les destine. FLIR Systems, Inc. ne
pourra être tenu pour responsable en cas de mauvaise
utilisation ou de mise en place de mesures de sécurité
insuffisantes.
Le non respect de tout ou partie des procédures
recommandées ou des messages d'AVERTISSEMENT
ou d'ATTENTION de la part de l'installateur, du
propriétaire ou de l'utilisateur dégagera FLIR Systems,
Inc. et ses agents de toute responsabilité en résultant.
Les spécifications et informations contenues dans ce
guide sont sujettes à modification sans préavis.

This document does not contain any export-controlled information.
Document Scope and Purpose
2
CM-640x Installation and User Guide - Revision 100 - December 2020
General Cautions and Warnings
This section contains information that indicates a
procedure or condition where there are potential
hazards.
SAVE ALL SAFETY AND OPERATING
INSTRUCTIONS FOR FUTURE USE.
Although the unit is designed and manufactured in
compliance with all applicable safety standards, certain
hazards are present during the installation of this
equipment.
To help ensure safety and to help reduce risk of injury or
damage, observe the following:
Précautions et avertissements
d'ordre général
Cette section contient des informations indiquant qu'une
procédure ou condition présente des risques potentiels.
CONSERVEZ TOUTES LES INSTRUCTIONS DE
SÉCURITÉ ET D'UTILISATION POUR POUVOIR VOUS
Y RÉFÉRER ULTÉRIEUREMENT.
Bien que l'unité soit conçue et fabriquée conformément à
toutes les normes de sécurité en vigueur, l'installation de
cet équipement présente certains risques.
Afin de garantir la sécurité et de réduire les risques de
blessure ou de dommages, veuillez respecter les
consignes suivantes:
Caution:
· The unit’s cover is an essential part of the product. Do not open or remove it.
· Never operate the unit without the cover in place. Operating the unit without the cover poses a risk of fire
and shock hazards.
· Do not disassemble the unit or remove screws. There are no user serviceable parts inside the unit.
· Only qualified trained personnel should service and repair this equipment.
· Observe local codes and laws and ensure that installation and operation are in accordance with fire,
security and safety standards.
Attention:
· Le cache de l'unité est une partie essentielle du produit. Ne les ouvrez et ne les retirez pas.
· N'utilisez jamais l'unité sans que le cache soit en place. L'utilisation de l'unité sans cache présente un
risque d'incendie et de choc électrique.
· Ne démontez pas l'unité et ne retirez pas ses vis. Aucune pièce se trouvant à l'intérieur de l'unité ne
nécessite un entretien par l'utilisateur.
· Seul un technicien formé et qualifié est autorisé à entretenir et à réparer cet équipement.
· Respectez les codes et réglementations locaux, et assurez-vous que l'installation et l'utilisation sont
conformes aux normes contre l'incendie et de sécurité.
A Warning is a precautionary message that indicates a procedure or condition where there are
potential hazards of personal injury or death.
Avertissement est un message préventif indiquant qu'une procédure ou condition présente un risque
potentiel de blessure ou de mort.

This document does not contain any export-controlled information.
Document Scope and Purpose
3
CM-640x Installation and User Guide - Revision 100 - December 2020
A Caution is a precautionary message that indicates a procedure or condition where there are potential
hazards of permanent damage to the equipment and or loss of data.
Attention est un message préventif indiquant qu'une procédure ou condition présente un risque
potentiel de dommages permanents pour l'équipement et/ou de perte de données.
ANote is useful information to prevent problems, help with successful installation, or to provide
additional understanding of the products and installation.
Une Remarque est une information utile permettant d'éviter certains problèmes, d'effectuer une
installation correcte ou de mieux comprendre les produits et l'installation.
ATip is information and best practices that are useful or provide some benefit for installation and use of
FLIR products.
Un Conseil correspond à une information et aux bonnes pratiques utiles ou apportant un avantage
supplémentaire pour l'installation et l'utilisation des produits FLIR.

This document does not contain any export-controlled information.
Camera Overview
4
CM-640x Installation and User Guide - Revision 100 - December 2020
2 Camera Overview
Quasar CM-640x cameras provide real-time video with 4K UHD (CP-6408-11-I) or 2560x1920 (CP-6405-
11-I) high definition quality, up to 25/30 frames per second (fps). They feature True Shutter Wide
Dynamic Range up to 130db; line-level audio in/out; digital I/O; and infrared (IR) illumination. When the
camera is connected to an IP network, it functions as a server, providing services such as camera
control, video streaming, and network communications.
Up to four streams can be run simultaneously with H.265, H.264, or MJPEG compression, providing an
ideal solution when differing levels of image quality are required. The camera can increase frame rate
and level of detail when events are triggered. In addition, FLIR's adaptive streaming algorithms provide
the highest image quality with the lowest bandwidth and storage requirements.
If help is needed during the installation process, contact the local FLIR service representative or call the
support number that appears on the product's page at https://www.flir.com/support/. All installers and
integrators are encouraged to take advantage of the training offered by FLIR; visit
https://www.flir.com/support-center/training/ for more information.
For safety, and to achieve the highest levels of performance from the camera system, always follow the
warnings and cautions in this manual when handling and operating the camera.
Related Documentation
· CM-640x Quick Install Guide
· FLIR Security Cameras - Accessory Guide
· DNA User Guide (see Accessing Product Information from the FLIR Website)
2.1 Features
· Progressive 4K 1/1.8" or 5MP
1/2.7" CMOS sensor,
depending on the model
· CP-6408-11-I: Up to 4K
(3840x2160) at 25/30fps
· CP-6405-11-I: Up to 5MP
(2560x1920) at 25/30fps
· Powered by IEEE 802.3af
class 0 PoE, 24 VAC, or 12
VDC
· Supports Internet Explorer
11.0 (recommended),
Chrome, Firefox, and Safari
browsers
· Supports 8GB to 512GB
microSD/microSDHC/microS
DXC (Class 10) cards
· H.265, H.264, and MJPEG
compression
· Motion detection event-driven
alarms
· 802.1X and SSL/TLS security
protocols
· Shutter (True) WDR
· 3DNR image noise reduction
· Backlight compensation
· IP66 enclosure with IK10
vandal-proof protection
· HTTP streaming MJPEG
· Built-in web server
· Tampering detection and
notifications
· Infrared LED illuminator
· True day/night (ICR)
· Five privacy masks
· White balance
· Up to 20 users
· Audio line-in/line-out
· SNMP v1/v2/v3 and SNMP
traps
· ONVIF© Profile S/G/T
· Alarm in/out
· UPnP support

This document does not contain any export-controlled information.
Camera Overview
5
CM-640x Installation and User Guide - Revision 100 - December 2020
2.2 Accessing Product Information from the FLIR Website
Up-to-date resources for the camera, including the camera’s specifications, the FLIR Discovery Network
Assistant (DNA) software tool, and this installation and user guide, are available from the camera’s
product details and support pages on FLIR.com.
To access product information from the FLIR website
1. Open FLIR.com and navigate to Products > Security > Visible Security Cameras.
Visible Security Cameras Page on FLIR.com
2. Find and click the camera. The camera’s product details page appears. For example,
Product Information Page on FLIR.com (Example)
3. Scroll down to see the camera’s specifications and related documents.

This document does not contain any export-controlled information.
Camera Overview
6
CM-640x Installation and User Guide - Revision 100 - December 2020
4. Click Go to Product Support to open the camera’s support page. For example,
Product Support Page Documents Tab (Example)
5. For documents, click the Documents tab. For downloads, including the DNA (Discovery Network
Assistant) tool, click the Downloads tab.
6. Click the relevant Download link.
2.3 Camera Dimensions
CM-640x Dimensions

This document does not contain any export-controlled information.
Installation
7
CM-640x Installation and User Guide - Revision 100 - December 2020
3 Installation
Caution:
· Except as described in this manual, do not open the camera for any reason. Damage to the
camera can occur as the result of careless handling or electrostatic discharge (ESD). Always
handle the camera with care to avoid damage to electrostatic-sensitive components.
· Prior to making any connections, ensure the power supply or circuit breaker is switched off.
· Operating the camera outside of the specified input voltage range or the specified operating
temperature range can cause permanent damage.
Installing the camera consists of:
1. Preparation
2. Initial Configuration
3. Mounting and Connecting the Camera
4. Additional Configuration Steps
5. Attaching the Camera to a Supported VMS
3.1 Preparation
This section contains the following important preparation information:
· Supplied Components
· Site Preparation - General
· Indoor Mounting
· Outdoor Mounting
· Pre-Installation Checklist
· Power Supply Options
3.1.1 Supplied Components
Before proceeding, check that the box contains the items listed (images not to scale). If any item is
missing or has defects, do not install or operate the product. Contact your dealer for assistance.
CM-640x Mini-Dome Camera

This document does not contain any export-controlled information.
Installation
8
CM-640x Installation and User Guide - Revision 100 - December 2020
M4 25mm Self-Tapping Screw x 4
Plastic Screw Anchor x 4
Torx Security (Tamper Resistant) Wrench
CM-640x Quick Install Guide
Note:
The self-tapping screws are mainly for softer substrate/material installation such as wood. For other
installation materials such as cement ceilings, it is necessary to pre-drill and use plastic anchors before
fastening the supplied self-tapping screws into the wall.
3.1.2 Site Preparation - General
There are several requirements that should be properly addressed prior to installation at the site.
The following specifications are requirements for proper installation and operation of the unit:
· Ambient Environment Conditions: Avoid positioning the unit near heaters or heating system
outputs. Avoid exposure to direct sunlight. Use proper maintenance to ensure that the unit is free
from dust, dirt, smoke, particles, chemicals, smoke, water or water condensation, and exposure
to EMI.
· Accessibility: The location used should allow easy access to unit connections and cables.
· Safety: Cables and electrical cords should be routed in a manner that prevents safety hazards,
such as from tripping, wire fraying, overheating, etc. Ensure that nothing rests on the unit’s
cables or power cords.
· Ample Air Circulation: Leave enough space around the unit to allow free air circulation.
· Cabling Considerations: Units should be placed in locations that are optimal for the type of
video cabling used between the unit and the cameras and external devices. Using a cable longer
than the manufacturer’s specifications for optimal video signal may result in degradation of color
and video parameters.
· Physical Security: The unit provides threat detection for physical security systems. In order to
ensure that the unit cannot be disabled or tampered with, the system should be installed with
security measures regarding physical access by trusted and un-trusted parties.
· Network Security: The unit transmits over IP to security personnel for video surveillance. Proper
network security measures should be in place to assure networks remain operating and free from
malicious interference. Install the unit on the backbone of a trusted network.
· Electrostatic Safeguards: The unit and other equipment connected to it (relay outputs, alarm
inputs, racks, carpeting, etc.) shall be properly grounded to prevent electrostatic discharge.

This document does not contain any export-controlled information.
Installation
9
CM-640x Installation and User Guide - Revision 100 - December 2020
Warning:
Before drilling into surfaces for camera mounting, verify that electrical or other utility service lines are
not present. Serious injury or death may result from failure to heed this warning.
The physical installation of the unit is the first phase of making the unit operational in a security plan. The
goal is to physically place the unit, connect it to other devices in the system, and to establish network
connectivity. When finished with the physical installation, complete the second phase of installation,
which is the setup and configuration of the unit.
3.1.3 Indoor Mounting
Read the instructions provided in this chapter thoroughly before installing the camera. Following are
additional considerations for indoor installation:
· There must be a fuse or circuit breaker at the starting point of the electrical wiring infrastructure.
· For indoor installations, such as industrial applications, the camera must be protected from hostile
external elements (e.g. corrosive environment, metallic dust, extreme temperatures, soot, over spray,
etc.).
· Do not place the camera on or near radiators and heat sources.
· All electrical work must be performed in accordance with local regulatory requirements.
3.1.4 Outdoor Mounting
Following are additional considerations for outdoor installation:
· For outside wiring installation, always use weatherproof equipment, such as boxes, receptacles,
connectors, etc.
· For electrical wiring, use the properly rated sheathed cables for conditions to which the cable will be
exposed (for example, moisture, heat, UV, physical requirements, etc.).
· Plan ahead to determine where to install infrastructure weatherproof equipment. Whenever possible,
ground components to an outdoor ground.
· Use best security practices to design and maintain secured camera access, communications
infrastructure, tamper-proof outdoor boxes, etc.
· All electrical work must be performed in accordance with local regulatory requirements.
3.1.5 Pre-Installation Checklist
Before installing the unit, make sure that:
· Instructions in the Document Scope and Purpose section are followed.
· All related equipment is powered off during the installation.
· Use best security practices to design and maintain secured camera access, communications
infrastructure, tamper-proof outdoor boxes, etc.

This document does not contain any export-controlled information.
Installation
10
CM-640x Installation and User Guide - Revision 100 - December 2020
Caution:
To avoid damage from overheating or unit failure, assure that there is sufficient temperature regulation
to support the unit’s requirements (cooling/heating). Operating temperature should be kept in the
following ranges, with no more than 90% non-condensing humidity:
· With heater: -55°C to 60°C (-67°F to 140°F)
· Cold start with heater: -55°C to 60°C (-67°F to 140°F)
Attention:
Afin d'éviter tout dommage dû à une surchauffe ou toute panne de l'unité, assurez-vous que la
régulation de température est suffisante pour répondre aux exigences de l'unité
(refroidissement/chauffage). La temperature de fonctionnement doit etre maintenue dans la fourchette
de temperature suivante, avec un maximum de 90% d'humidite non condensee:
· Avec chauffage: -55°C à 60°C (-67°F à 140°F)
· Démarrage à froid avec chauffage: -55°C à 60°C (-67°F à 140°F)
3.1.6 Power Supply Options
The camera can be powered by:
· A UL-listed L.P.S. (Limited Power Supply) unit, rated to a maximum temperature of 60° C:
o12 VDC, 1.21A minimum
o24 VAC, 50/60Hz, 1.2A minimum
· IEEE 802.3af class 0 PoE (Power over Ethernet): 48 VDC, 0.27A minimum. Make sure that a
Power Sourcing Equipment (PSE) device is used in the network.
Warning:
All electrical work must be performed by a qualified service person in accordance with local regulatory
requirements.
Avertissement:
Toutes les interventions électriques doivent être effectuées par un technicien qualifié conformément
aux reglementations locales.

This document does not contain any export-controlled information.
Installation
11
CM-640x Installation and User Guide - Revision 100 - December 2020
Powering the Camera
For assistance with purchasing a power supply, contact your FLIR representative.
3.2 Initial Configuration
FLIR recommends configuring the camera on a bench or in a lab before mounting and aiming it.
However, it is also possible to mount the camera before configuring it, which could be more appropriate
for certain installations.
You can configure the camera using the FLIR Discovery Network Assistant (DNA) software tool, the
camera's web page, or a supported VMS.
Task
DNA tool
Camera's web page
Discover camera IP address
•
Configure IP address, mask, and gateway
•
•
Configure DNS settings, MTU, and Ethernet speed
•
Change user credentials
•
•
Change video format
•
•
Configure more than one camera at the same time
•
FLIR recommends using the DNA tool to discover the camera on the network. For more information about
using a supported VMS to configure one or more cameras at the same time, see the VMS
documentation.
To configure the camera for the first time:
1. Remove Dome Cover and Separate Base from Mounting Bracket
2. Connect the Camera
3. Configure for Networking
4. Change Video Format (Optional)
5. Re-attach Dome Cover

This document does not contain any export-controlled information.
Installation
12
CM-640x Installation and User Guide - Revision 100 - December 2020
Using DNA to Configure the Camera
DNA is a user-friendly utility that easily discovers and configures FLIR Security edge devices on a
network. It does not require a license to use and is a free download from the product's support page on
FLIR.com (see Accessing Product Information from the FLIR Website).
DNA provides a central location for listing all the supported FLIR Security camera models accessible over
the network. Once listed, each camera can be right-clicked to access and change the network settings. If
the network settings are changed for some reason, a new search will relist the units. The units can then
be configured via the camera's web page.
The camera must be made accessible for setting network addresses.
To configure the camera via a LAN, you must attach the camera via the network switch or router to the
same subnet (network segment or VLAN) as the computer that manages the unit. If the PC is on a
different subnet than the camera, you will not be able to access the camera via a web browser.
If there is a DHCP server on the network, FLIR recommends using the DNA tool to discover the camera
and change its IP address.
If FLIR’s Latitude VMS is being used, configure the unit with a static IP address rather than with DHCP.
This ensures that the IP address will not automatically change in the future and interfere with
configurations and communication.
For more information about using the DNA tool, see the DNA User Guide. While the software is open,
click the Help icon .
3.2.1 Remove Dome Cover and Separate Base from Mounting Bracket
Tip:
When unpacking the camera, do not remove the plastic sheet protecting the dome.
To remove the dome cover:
1. Using the Torx wrench, loosen the screw on the camera's outer circular ring that secures the dome
cover to the camera base.
2. While firmly holding the base, rotate the ring counterclockwise to loosen it.
3. Carefully pull the ring and cover away from the base.
Outer Ring Locking Screw
Loosen Ring

This document does not contain any export-controlled information.
Installation
13
CM-640x Installation and User Guide - Revision 100 - December 2020
To separate the camera base from the mounting bracket:
1. Using a screwdriver, loosen the two twist-lock
screws securing the camera and its base to the
mounting bracket.
2. Gently pull the camera and its base away from
the mounting bracket.
Change the number of LEDs (optional)
The camera has a total of eight IR illumination LEDs.
On the 3D lens assembly, there is a 4 / 8 (default)
switch that determines the number of enabled IR
LEDs. With the dome cover removed, you can
change the switch setting.
3.2.2 Connect the Camera
Warning:
This product contains a battery that is soldered to the PCB. There is a risk of explosion if the battery is
replaced by an incorrect type. Do not replace the battery. The battery should be disposed of in
accordance with the battery manufacturer’s instructions.
Connectors
Connector
Connection
1
RJ-45
Two LEDs
Attach a Cat 6 cable from the network switch to the RJ45 connector for a 10/100/1000
Mbps Ethernet and IEEE 802.3af class 0 PoE connection. Ethernet is required for
streaming video and for configuring the camera.
The green link LED indicates a good network connection. The orange activity LED
flashes to indicate network activity.

This document does not contain any export-controlled information.
Installation
14
CM-640x Installation and User Guide - Revision 100 - December 2020
Connector
Connection
2
Four-pin power terminal
block
1
24VAC -
3
12VDC -
If using a 24VAC or 12VDC power supply,
connect the wires to the power terminal block
connector according to the pin assignment shown.
2
24VAC +
4
12VDC +
3
Default Button
To restore the camera to its factory defaults, use a proper tool to press the default
button for at least 20 seconds.
4
USB
Connects to Wi-Fi dongle (future release support)
5
microSD Card Slot
For video clip and snapshot recording and file storage, insert a microSD / SDHC /
SDXC card (up to 512 GB, Class 10) in the card slot. When the camera is powered
on, do not remove the microSD card.
6
Nine-pin I/O terminal
block
1
Audio In L
6
Alarm Out +
Attach wires from external devices to the terminal
block connector for alarm and audio in/out
according to the pin assignment shown.
2
Audio In R
7
3
GND
8
Alarm In +
4
Audio Out L
9
5
Audio Out R
Warning:
Do not connect an external power supply to the nine-pin audio/alarm I/O terminal block connector.
Warnings:
· The power cord to the 12 VDC or 24 VAC power supply unit must be connected to a socket
outlet with an earthing connector.
· The PoE unit and all interconnected equipment must be installed indoors within the same
building, including all PoE-powered network connections, as described by Environment A of the
IEEE 802.3af standard.
· All electrical work must be performed by a qualified service person in accordance with local
regulatory requirements.
Avertissement:
· Le cordon du bloc d'alimentation 12V ou 24V doit être connecté à une prise de courant avec un
connecteur de mise à la terre.
· L'unité PoE et tous les équipements interconnectés doivent être installés à l'intérieur du même
bâtiment, y compris toutes les connexions réseau alimentées par PoE, comme décrit par
l'environnement A de la norme IEEE 802.3af.
· Toutes les interventions électriques doivent être effectuées par un technicien qualifié
conformément aux reglementations locales.