Analog
MPX
Connect to a
12V DC or 24V AC
power supply.*
Image Sensor 1/3” 1.3MP CMOS
Video Format NTSC (C234BC)/PAL (C234BCP)
Effective Pixels H: 1305 V: 1049
Resolution Digital: 720p
Analog: 960H
Scan System Progressive
Sync System Internal
S / N Ratio ≥50dB (AGC Off)
Iris AES
AES Shutter Speed 1/60 (1/50) ~ 1/60,000 sec.
Min. Illumination 0.1 LUX (IR Off)
0 LUX (IR LEDs On)
Video Output Digital: 720p MPX HD-CVI
Analog: Composite 1.0Vpp @ 75ohm
Lens Focal Length / Type 2.8-12mm F1.4 / Varifocal
FOV (Horizontal) Digital: 30-80°
Analog: 30-80°
Termination BNC Type
IR Range / Qty. 115ft / 35m; 42 IR LED’s
Power Requirement 12V DC ± 10%
24V AC ± 10%
Power Consumption 12V DC: 510mA MAX with IR LED
24V AC: 320mA MAX with IR LED
Operating Temp. Range –22° ~ 140°F / –30° ~ 60°C
Environmental Rating IP66
Dimensions (W x H x D) 3.9” x 3.5” x 10.6”
99mm x 89mm x 269mm
Weight (including stand) 1.7lbs / 0.8kg
Camera Dimensions
Camera Specifications
To install the camera:
1. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE: Insert the included drywall anchors if installing into
drywall.
2. Connect the video and power cable as detailed in the
section ‘Setting up the Camera’.
3. Attach the camera
base to the mouting
surface using the
included screws.
4. Set the position and angle of the camera using the
provided Allen key.
5. Remove the protective film from the camera lens.
Setting up the Camera
10.6”
269mm
3.9”
99mm
3.5”
89mm
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
Installing the Camera
WARNING:
A REGULATED 12V DC or 24V AC power supply is REQUIRED for
use with this camera. Use of a non-regulated, non-conforming
power supply can damage this product and voids the warranty.
Camera Wiring
1. Connect one of the two BNC connectors on the camera to
the video cable. See “Camera Wiring” for details.
2. Connect a power source to the power terminal block. The
camera supports both 12V DC and 24V AC power supplies.
NOTE: Make sure to follow correct polarity as marked on the
power connector. For AC power, connect multiple cameras
using consistent wiring polarity to prevent video rolling.
Extension Cable Options
Specification Maximum Length
RG59 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 1500ft (455m)†
RG6 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 2300ft (700m)†
Analog CCTV Balun Up to 300ft (91m)
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
The entire length of the cable run must be made using a
single extension cable between the camera and the DVR.
B) Loosen lower screw with
the Allen key to adjust the
camera’s vertical position.
C) Loosen the screws on either side of the
camera stand with the Allen key to rotate the
camera housing. Loosen the right-side to make
fine adjustments, or the left-side for broad
adjustments.
A) Loosen the screw on the
camera base with the Allen
key to tighten / loosen the
stand connection. Adjust the
camera’s horizontal position.
A B
C
MPX
Connect to an MPX DVR for
720p viewing / recording.
Analog
Connect to an analog DVR for
960H viewing / recording.
Adjusting Zoom & Focus
Use the included Allen key to adjust
the zoom and focus control screws
on the underside of the camera as
required.
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection past
200ft (61m).
