FLIR TG130 User manual

User’s manual
FLIR TG130

Important note
Before operating the device, you must read, understand, and follow all instructions, warnings, cautions, and legal disclaimers.
Důležitá poznámka
Před použitím zařízení si přečtěte veškeré pokyny, upozornění, varování a vyvázání se ze záruky, ujistěte se, že jim rozumíte, a řiďte se
jimi.
Vigtig meddelelse
Før du betjener enheden, skal du du læse, forstå og følge alle anvisninger, advarsler, sikkerhedsforanstaltninger og ansvarsfraskrivelser.
Wichtiger Hinweis
Bevor Sie das Gerät in Betrieb nehmen, lesen, verstehen und befolgen Sie unbedingt alle Anweisungen, Warnungen, Vorsichtshinweise
und Haftungsausschlüsse
Σημαντική σημείωση
Πριν από τη λειτουργία της συσκευής, πρέπει να διαβάσετε, να κατανοήσετε και να ακολουθήσετε όλες τις οδηγίες,
προειδοποιήσεις, προφυλάξεις και νομικές αποποιήσεις.
Nota importante
Antes de usar el dispositivo, debe leer, comprender y seguir toda la información sobre instrucciones, advertencias, precauciones y
renuncias de responsabilidad.
Tärkeä huomautus
Ennen laitteen käyttämistä on luettava ja ymmärrettävä kaikki ohjeet, vakavat varoitukset, varoitukset ja lakitiedotteet sekä noudatettava
niitä.
Remarque importante
Avant d'utiliser l'appareil, vous devez lire, comprendre et suivre l'ensemble des instructions, avertissements, mises en garde et clauses
légales de non-responsabilité.
Fontos megjegyzés
Az eszköz használata előtt figyelmesen olvassa el és tartsa be az összes utasítást, figyelmeztetést, óvintézkedést és jogi nyilatkozatot.
Nota importante
Prima di utilizzare il dispositivo, è importante leggere, capire e seguire tutte le istruzioni, avvertenze, precauzioni ed esclusioni di
responsabilità legali.
重要な注意
デバイスをご使用になる前に、あらゆる指示、警告、注意事項、および免責条項をお読み頂き、その内容を理解して従ってください。
중요한 참고 사항
장치를 작동하기 전에 반드시 다음의 사용 설명서와 경고,주의사항,법적 책임제한을 읽고 이해하며 따라야 합니다.
Viktig
Før du bruker enheten, må du lese, forstå og følge instruksjoner, advarsler og informasjon om ansvarsfraskrivelse.
Belangrijke opmerking
Zorg ervoor dat u, voordat u het apparaat gaat gebruiken, alle instructies, waarschuwingen en juridische informatie hebt doorgelezen en
begrepen, en dat u deze opvolgt en in acht neemt.
Ważna uwaga
Przed rozpoczęciem korzystania z urządzenia należy koniecznie zapoznać się z wszystkimi instrukcjami, ostrzeżeniami, przestrogami i
uwagami prawnymi. Należy zawsze postępować zgodnie z zaleceniami tam zawartymi.
Nota importante
Antes de utilizar o dispositivo, deverá proceder à leitura e compreensão de todos os avisos, precauções, instruções e isenções de
responsabilidade legal e assegurar-se do seu cumprimento.
Важное примечание
До того, как пользоваться устройством, вам необходимо прочитать и понять все предупреждения, предостережения и
юридические ограничения ответственности и следовать им.
Viktig information
Innan du använder enheten måste du läsa, förstå och följa alla anvisningar, varningar, försiktighetsåtgärder och ansvarsfriskrivningar.
Önemli not
Cihazı çalıştırmadan önce tüm talimatları, uyarıları, ikazları ve yasal açıklamaları okumalı, anlamalı ve bunlara uymalısınız.
重要注意事项
在操作设备之前，您必须阅读、理解并遵循所有说明、警告、注意事项和法律免责声明。
重要注意事項
操作裝置之前，您務必閱讀、了解並遵循所有說明、警告、注意事項與法律免責聲明。

User’s manual
FLIR TG130
#T559971; r. AE/32684/32684; en-US v

Table of contents
1 Disclaimers ........................................................................................1
1.1 Legal disclaimer ......................................................................... 1
1.2 Usage statistics ..........................................................................1
1.3 Changes to registry .....................................................................1
1.4 U.S. Government Regulations........................................................ 1
1.5 Copyright ..................................................................................1
1.6 Quality assurance ....................................................................... 1
1.7 Patents.....................................................................................1
1.8 EULATerms ..............................................................................1
1.9 EULATerms ..............................................................................2
2 Safety information ...............................................................................3
3 Notice to user .....................................................................................4
3.1 User-to-user forums ....................................................................4
3.2 Calibration................................................................................. 4
3.3 Accuracy ..................................................................................4
3.4 Disposal of electronic waste .......................................................... 4
3.5 Training ....................................................................................4
3.6 Documentation updates ............................................................... 4
3.7 Important note about this manual.................................................... 4
3.8 Note about authoritative versions.................................................... 5
4 Customer help ....................................................................................6
4.1 General ....................................................................................6
4.2 Submitting a question .................................................................. 6
4.3 Downloads................................................................................7
5 Introduction........................................................................................8
6 Quick start guide .................................................................................9
7 Description.......................................................................................10
7.1 View from the front .................................................................... 10
7.1.1 Figure.......................................................................... 10
7.1.2 Explanation................................................................... 10
7.2 View from the rear..................................................................... 10
7.2.1 Figure.......................................................................... 10
7.2.2 Explanation................................................................... 10
7.3 Screen elements ...................................................................... 11
7.3.1 Figure.......................................................................... 11
7.3.2 Explanation................................................................... 11
7.3.3 Status icons and indicators............................................... 11
8 Operation .........................................................................................12
8.1 Replacing the batteries .............................................................. 12
8.2 Turning on and turning off the camera............................................ 12
8.2.1 Auto off........................................................................ 12
8.3 Freezing the image.................................................................... 12
8.4 Changing the temperature unit..................................................... 12
9 Technical data...................................................................................14
9.1 Online field-of-view calculator ...................................................... 14
9.2 Note about technical data ........................................................... 14
9.3 Note about authoritative versions.................................................. 14
9.4 FLIR TG130 (Global) ................................................................. 15
#T559971; r. AE/32684/32684; en-US vii

Table of contents
10 Mechanical drawings ......................................................................... 17
11 Cleaning the camera .......................................................................... 19
11.1 Camera housing, cables, and other items....................................... 19
11.1.1 Liquids......................................................................... 19
11.1.2 Equipment .................................................................... 19
11.1.3 Procedure .................................................................... 19
11.2 Infrared lens ............................................................................ 19
11.2.1 Liquids......................................................................... 19
11.2.2 Equipment .................................................................... 19
11.2.3 Procedure .................................................................... 19
12 Application examples......................................................................... 20
12.1 Moisture & water damage ........................................................... 20
12.1.1 General........................................................................ 20
12.1.2 Figure.......................................................................... 20
12.2 Faulty contact in socket .............................................................. 20
12.2.1 General........................................................................ 20
12.2.2 Figure.......................................................................... 21
12.3 Oxidized socket........................................................................ 21
12.3.1 General........................................................................ 21
12.3.2 Figure.......................................................................... 21
12.4 Insulation deficiencies................................................................ 22
12.4.1 General........................................................................ 22
12.4.2 Figure.......................................................................... 22
12.5 Draft ...................................................................................... 23
12.5.1 General........................................................................ 23
12.5.2 Figure.......................................................................... 23
13 About FLIR Systems .......................................................................... 25
13.1 More than just an infrared camera ................................................ 26
13.2 Sharing our knowledge .............................................................. 26
13.3 Supporting our customers........................................................... 27
14 Glossary ..........................................................................................28
15 History of infrared technology............................................................. 31
#T559971; r. AE/32684/32684; en-US viii

Disclaimers
1
1.1 Legal disclaimer
All products manufactured by FLIR Systems are warranted against defective
materials and workmanship for a period of one (1) year from the delivery date
of the original purchase, provided such products have been under normal stor-
age, use and service, and in accordance with FLIR Systems instruction.
Uncooled handheld infrared cameras manufactured by FLIR Systems are war-
ranted against defective materials and workmanship for a period of two (2)
years from the delivery date of the original purchase, provided such products
have been under normal storage, use and service, and in accordance with
FLIR Systems instruction, and provided that the camera has been registered
within 60 days of original purchase.
Detectors for uncooled handheld infrared cameras manufactured by FLIR Sys-
tems are warranted against defective materials and workmanship for a period
of ten (10) years from the delivery date of the original purchase, provided such
products have been under normal storage, use and service, and in accordance
with FLIR Systems instruction, and provided that the camera has been regis-
tered within 60 days of original purchase.
Products which are not manufactured by FLIR Systems but included in sys-
tems delivered by FLIR Systems to the original purchaser, carry the warranty, if
any, of the particular supplier only. FLIR Systems has no responsibility whatso-
ever for such products.
The warranty extends only to the original purchaser and is not transferable. It
is not applicable to any product which has been subjected to misuse, neglect,
accident or abnormal conditions of operation. Expendable parts are excluded
from the warranty.
In the case of a defect in a product covered by this warranty the product must
not be further used in order to prevent additional damage. The purchaser shall
promptly report any defect to FLIR Systems or this warranty will not apply.
FLIR Systems will, at its option, repair or replace any such defective product
free of charge if, upon inspection, it proves to be defective in material or work-
manship and provided that it is returned to FLIR Systems within the said one-
year period.
FLIR Systems has no other obligation or liability for defects than those set forth
above.
No other warranty is expressed or implied. FLIR Systems specifically disclaims
the implied warranties of merchantability and fitness for a particular purpose.
FLIR Systems shall not be liable for any direct, indirect, special, incidental or
consequential loss or damage, whether based on contract, tort or any other le-
gal theory.
This warranty shall be governed by Swedish law.
Any dispute, controversy or claim arising out of or in connection with this war-
ranty, shall be finally settled by arbitration in accordance with the Rules of the
Arbitration Institute of the Stockholm Chamber of Commerce. The place of ar-
bitration shall be Stockholm. The language to be used in the arbitral proceed-
ings shall be English.
1.2 Usage statistics
FLIR Systems reserves the right to gather anonymous usage statistics to help
maintain and improve the quality of our software and services.
1.3 Changes to registry
The registry entry HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet
\Control\Lsa\LmCompatibilityLevel will be automatically changed to level 2 if
the FLIR Camera Monitor service detects a FLIR camera connected to the
computer with a USB cable. The modification will only be executed if the cam-
era device implements a remote network service that supports network logons.
1.4 U.S. Government Regulations
This product may be subject to U.S. Export Regulations. Please send any in-
quiries to [email protected].
1.5 Copyright
© 2015, FLIR Systems, Inc. All rights reserved worldwide. No parts of the soft-
ware including source code may be reproduced, transmitted, transcribed or
translated into any language or computer language in any form or by any
means, electronic, magnetic, optical, manual or otherwise, without the prior
written permission of FLIR Systems.
The documentation must not, in whole or part, be copied, photocopied, repro-
duced, translated or transmitted to any electronic medium or machine read-
able form without prior consent, in writing, from FLIR Systems.
Names and marks appearing on the products herein are either registered
trademarks or trademarks of FLIR Systems and/or its subsidiaries. All other
trademarks, trade names or company names referenced herein are used for
identification only and are the property of their respective owners.
1.6 Quality assurance
The Quality Management System under which these products are developed
and manufactured has been certified in accordance with the ISO 9001
standard.
FLIR Systems is committed to a policy of continuous development; therefore
we reserve the right to make changes and improvements on any of the prod-
ucts without prior notice.
1.7 Patents
One or several of the following patents and/or design patents may apply to the
products and/or features. Additional pending patents and/or pending design
patents may also apply.
000279476-0001; 000439161; 000499579-0001; 000653423; 000726344;
000859020; 001106306-0001; 001707738; 001707746; 001707787;
001776519; 001954074; 002021543; 002058180; 002249953; 002531178;
0600574-8; 1144833; 1182246; 1182620; 1285345; 1299699; 1325808;
1336775; 1391114; 1402918; 1404291; 1411581; 1415075; 1421497;
1458284; 1678485; 1732314; 2106017; 2107799; 2381417; 3006596;
3006597; 466540; 483782; 484155; 4889913; 5177595; 60122153.2;
602004011681.5-08; 6707044; 68657; 7034300; 7110035; 7154093;
7157705; 7237946; 7312822; 7332716; 7336823; 7544944; 7667198;
7809258 B2; 7826736; 8,153,971; 8,823,803; 8,853,631; 8018649 B2;
8212210 B2; 8289372; 8354639 B2; 8384783; 8520970; 8565547; 8595689;
8599262; 8654239; 8680468; 8803093; D540838; D549758; D579475;
D584755; D599,392; D615,113; D664,580; D664,581; D665,004; D665,440;
D677298; D710,424 S; D718801; DI6702302-9; DI6903617-9; DI7002221-6;
DI7002891-5; DI7002892-3; DI7005799-0; DM/057692; DM/061609; EP
2115696 B1; EP2315433; SE 0700240-5; US 8340414 B2; ZL
201330267619.5; ZL01823221.3; ZL01823226.4; ZL02331553.9;
ZL02331554.7; ZL200480034894.0; ZL200530120994.2; ZL200610088759.5;
ZL200630130114.4; ZL200730151141.4; ZL200730339504.7;
ZL200820105768.8; ZL200830128581.2; ZL200880105236.4;
ZL200880105769.2; ZL200930190061.9; ZL201030176127.1;
ZL201030176130.3; ZL201030176157.2; ZL201030595931.3;
ZL201130442354.9; ZL201230471744.3; ZL201230620731.8.
1.8 EULA Terms
• You have acquired a device (“INFRARED CAMERA”) that includes soft-
ware licensed by FLIR Systems AB from Microsoft Licensing, GP or its af-
filiates (“MS”). Those installed software products of MS origin, as well as
associated media, printed materials, and “online” or electronic documen-
tation (“SOFTWARE”) are protected by international intellectual property
laws and treaties. The SOFTWARE is licensed, not sold. All rights
reserved.
• IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT
(“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. IN-
STEAD, PROMPTLY CONTACT FLIR Systems AB FOR INSTRUCTIONS
ON RETURN OF THE UNUSED DEVICE(S) FOR A REFUND. ANY USE
OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON
THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EU-
LA (OR RATIFICATION OF ANY PREVIOUS CONSENT).
•GRANT OF SOFTWARE LICENSE. This EULA grants you the following
license:
• You may use the SOFTWARE only on the DEVICE.
•NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLER-
ANT. FLIR Systems AB HAS INDEPENDENTLY DETERMINED
HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS
RELIED UPON FLIR Systems AB TO CONDUCT SUFFICIENT
TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE
FOR SUCH USE.
•NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is
provided “AS IS” and with all faults. THE ENTIRE RISK AS TO SAT-
ISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EF-
FORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU.
ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE
WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST IN-
FRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES RE-
GARDING THE DEVICE OR THE SOFTWARE, THOSE
WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT
BINDING ON, MS.
• No Liability for Certain Damages. EXCEPT AS PROHIBITED BY
LAW, MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPE-
CIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING
FROM OR IN CONNECTION WITH THE USE OR PERFORM-
ANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY
EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN
NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EX-
CESS OF U.S. TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).
•Limitations on Reverse Engineering, Decompilation, and Dis-
assembly. You may not reverse engineer, decompile, or disassem-
ble the SOFTWARE, except and only to the extent that such activity
is expressly permitted by applicable law notwithstanding this
limitation.
•SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS.
You may permanently transfer rights under this EULA only as part of
a permanent sale or transfer of the Device, and only if the recipient
agrees to this EULA. If the SOFTWARE is an upgrade, any transfer
must also include all prior versions of the SOFTWARE.
•EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is
subject to U.S. export jurisdiction. You agree to comply with all appli-
cable international and national laws that apply to the SOFTWARE,
including the U.S. Export Administration Regulations, as well as
end-user, end-use and destination restrictions issued by U.S. and
other governments. For additional information see http://www.micro-
soft.com/exporting/.
#T559971; r. AE/32684/32684; en-US 1

Disclaimers1
1.9 EULA Terms
Qt4 Core and Qt4 GUI, Copyright ©2013 Nokia Corporation and FLIR Sys-
tems AB. This Qt library is a free software; you can redistribute it and/or modify
it under the terms of the GNU Lesser General Public License as published by
the Free Software Foundation; either version 2.1 of the License, or (at your op-
tion) any later version. This library is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU Lesser General Public License, http://www.gnu.org/licenses/lgpl-2.1.html.
The source code for the libraries Qt4 Core and Qt4 GUI may be requested
from FLIR Systems AB.
#T559971; r. AE/32684/32684; en-US 2

Safety information
2
WARNING
Make sure that you read all applicable MSDS (Material Safety Data Sheets) and warning labels on con-
tainers before you use a liquid. The liquids can be dangerous. Injury to persons can occur.
CAUTION
Do not point the infrared camera (with or without the lens cover) at strong energy sources, for example,
devices that cause laser radiation, or the sun. This can have an unwanted effect on the accuracy of the
camera. It can also cause damage to the detector in the camera.
CAUTION
Do not use the camera in temperatures more than +50°C (+122°F), unless other information is specified
in the user documentation or technical data. High temperatures can cause damage to the camera.
CAUTION
Do not apply solvents or equivalent liquids to the camera, the cables, or other items. Damage to the bat-
tery and injury to persons can occur.
CAUTION
Be careful when you clean the infrared lens. The lens has an anti-reflective coating which is easily dam-
aged. Damage to the infrared lens can occur.
CAUTION
Do not use too much force to clean the infrared lens. This can cause damage to the anti-reflective
coating.
NOTE
The encapsulation rating is only applicable when all the openings on the camera are sealed with their cor-
rect covers, hatches, or caps. This includes the compartments for data storage, batteries, and
connectors.
#T559971; r. AE/32684/32684; en-US 3

Notice to user
3
3.1 User-to-user forums
Exchange ideas, problems, and infrared solutions with fellow thermographers around the
world in our user-to-user forums. To go to the forums, visit:
http://www.infraredtraining.com/community/boards/
3.2 Calibration
We recommend that you send in the camera for calibration once a year. Contact your local
sales office for instructions on where to send the camera.
3.3 Accuracy
For very accurate results, we recommend that you wait 5 minutes after you have started
the camera before measuring a temperature.
3.4 Disposal of electronic waste
As with most electronic products, this equipment must be disposed of in an environmen-
tally friendly way, and in accordance with existing regulations for electronic waste.
Please contact your FLIR Systems representative for more details.
3.5 Training
To read about infrared training, visit:
• http://www.infraredtraining.com
• http://www.irtraining.com
• http://www.irtraining.eu
3.6 Documentation updates
Our manuals are updated several times per year, and we also issue product-critical notifi-
cations of changes on a regular basis.
To access the latest manuals and notifications, go to the Download tab at:
http://support.flir.com
It only takes a few minutes to register online. In the download area you will also find the lat-
est releases of manuals for our other products, as well as manuals for our historical and
obsolete products.
3.7 Important note about this manual
FLIR Systems issues generic manuals that cover several cameras within a model line.
This means that this manual may contain descriptions and explanations that do not apply
to your particular camera model.
#T559971; r. AE/32684/32684; en-US 4

Notice to user3
3.8 Note about authoritative versions
The authoritative version of this publication is English. In the event of divergences due to
translation errors, the English text has precedence.
Any late changes are first implemented in English.
#T559971; r. AE/32684/32684; en-US 5

Customer help
4
4.1 General
For customer help, visit:
http://support.flir.com
4.2 Submitting a question
To submit a question to the customer help team, you must be a registered user. It only
takes a few minutes to register online. If you only want to search the knowledgebase for
existing questions and answers, you do not need to be a registered user.
When you want to submit a question, make sure that you have the following information to
hand:
• The camera model
• The camera serial number
• The communication protocol, or method, between the camera and your device (for ex-
ample, HDMI, Ethernet, USB, or FireWire)
#T559971; r. AE/32684/32684; en-US 6

Customer help
4
• Device type (PC/Mac/iPhone/iPad/Android device, etc.)
• Version of any programs from FLIR Systems
• Full name, publication number, and revision number of the manual
4.3 Downloads
On the customer help site you can also download the following:
• Firmware updates for your infrared camera.
• Program updates for your PC/Mac software.
• Freeware and evaluation versions of PC/Mac software.
• User documentation for current, obsolete, and historical products.
• Mechanical drawings (in *.dxf and *.pdf format).
• Cad data models (in *.stp format).
• Application stories.
• Technical datasheets.
• Product catalogs.
#T559971; r. AE/32684/32684; en-US 7

Introduction
5
Thank you for choosing a FLIR TG130 from FLIR Systems.
FLIR’s new FLIR TG130 imaging infrared thermometer bridges the gap between single-
spot infrared thermometers and FLIR’s legendary thermal cameras. Equipped with FLIR’s
exclusive Lepton micro thermal camera, the FLIR TG130 shows you where potential prob-
lems are brewing and where to aim your spot.
The FLIR TG130 lets you see heat patterns and reliably measure temperature. Its menu
uses intuitive icons, making it simple to operate.
Main features:
• See the heat and speed up troubleshooting.
• Know where to measure temperature.
• Grab and go simplicity—no special training required.
• Pocket portable to fit a crowded tool bag.
• Rugged and reliable.
#T559971; r. AE/32684/32684; en-US 8

Quick start guide
6
Follow this procedure:
1. Install the three standard AAA batteries.
2. Push the on/off button to turn on the camera.
3. Aim the camera toward an area or object of interest. The digital reading represents the
temperature at the position of the crosshair.
4. Pull the trigger to freeze the image.
5. Pull the trigger again to return to the live image.
#T559971; r. AE/32684/32684; en-US 9

Description
7
7.1 View from the front
7.1.1 Figure
7.1.2 Explanation
1. Infrared lens.
2. Trigger.
7.2 View from the rear
7.2.1 Figure
7.2.2 Explanation
1. Camera screen.
2. On/off button.
Function:
• Push to turn on the camera.
• Push and hold for more than 2 seconds to turn off the camera.
3. Battery compartment.
4. Lanyard access.
#T559971; r. AE/32684/32684; en-US 10

Description
7
7.3 Screen elements
7.3.1 Figure
7.3.2 Explanation
1. Crosshair temperature.
2. Crosshair.
7.3.3 Status icons and indicators
The battery low icon indicates that the batteries
must be replaced.
#T559971; r. AE/32684/32684; en-US 11

Operation
8
8.1 Replacing the batteries
If the battery low icon is displayed or if the camera does not power on, you must re-
place the batteries.
Follow this procedure:
1. Turn off the camera.
2. Lift up the battery compartment cover.
3. Remove the battery pack.
4. Replace the three standard AAA batteries, ensuring correct polarity.
5. Put the battery pack into the battery compartment.
6. Push down and secure the battery compartment cover. The cover makes a click when
it locks in place.
8.2 Turning on and turning off the camera
• To turn on the camera, push the on/off button.
• To turn off the camera, push and hold the on/off button for more than 2 seconds.
8.2.1 Auto off
The camera automatically turns off after 5 minutes of inactivity. A message is displayed 3
seconds before the camera turns off.
You can cancel the auto off sequence by pushing the on/off button. The camera then goes
back to live mode.
8.3 Freezing the image
Follow this procedure:
1. Aim the camera toward a point of interest.
2. Pull the trigger to freeze the image.
3. Pull the trigger again to return to the live image.
8.4 Changing the temperature unit
The camera displays temperatures in ℃or ℉. You change the temperature unit with a
switch, located in the battery compartment.
#T559971; r. AE/32684/32684; en-US 12