Flycam FLCM-FLN-PLA User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Flowline Placid 2-Axis Stabilizing Arm (FLCM-FLN-PLA)
Assembly Manua l
Tensioner Spring
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Safety Shock Cord

2
Remove the hook from Flowline support
bar.
Take the cord bundle out from the cup and
pull the whole cord unl a cord lock comes
out.
Flowline Placid Setup
Separate the cord from cord lock and keep
the lock aside for aaching it back
aerwards.
Separate the cord also from the cup and
keep aside for mounng it back later.
Use a tool to unscrew small bolts that hold
the front pulley, from each side.

3
Mount front pulley in between the cord,
and pull the cord so that it goes back inside
the support arm. Again use tools to ghten
the bolts from each side and set the pulley
at its posion.
Turn the Placid Arm upside down. By using
an allen key, loosen the mounng bracket of
Arm. Now the bracket has enough space for
the cord to pass through it.
Insert cord into the mounng bracket. Make
sure that it is going exactly in the centre, up
into the hole of the Placid arm. Then Pull
the cord from boom of Placid arm, near
the spring, while sll holding it upside
down.
To x Placid arm at its appropriate posion,
aach one side of Safety Elasc Cord to a
knob on Placid arm. Then, drag the other
side of elasc cord across Flowline support
arm, and aach to the knob on other side
of Placid arm.
Now you can hold the Placid arm in its
standard posion. The cord is aptly set to
perform its funcon. By using an allen key,
ghten the mounng bracket of Placid Arm
with Flowline support arm.
Pull out the front pulley carefully, so it
doesn’t drop into the Flowline support bar
and Insert the cord from the bottom hole
and take it out from the top hole.

4
Fix the hook back at its actual posion, using
an allen key. Now Set the provided Spring
again in the hook.
Wear support jacket and ghten the buckles
provided at the waist, adjust as per your
convenience. Tighten the buckles provided
at the chest of support jacket, and adjust as
per your convenience.
By adjusng side support, you will move the
weight on your hips, thus resulng in
comfortable long hour shoong.
Loosen the knob of hook and aach camera
to it. Tighten with provided knob to ensure
slip-free connecon.
Put-in the cup back through the cord and
relock it with the cord lock. Roll the leover
cord inside the cup.
Install Flycam Flowline Placid and change the Spring, Follow this
https://bit.ly/3Ae0t7a

5
YOUR FLOWLINE PLACID 2-AXIS STABILIZING ARM
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of
me, we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor
does it cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to
inspecon and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.