Follett HCD Operation manual

HCD/HMD/HCF/HMF1650R Ice Machines
Following installation, please forward this manual
to the appropriate operations person.
Operation and Service Manual
Order parts online
www.follettice.com
OZ
MADEIN
THEUSA
PSIG
MODEL SERIALNO
CORPORATION
PART NO
HZ
LOWSIDE
CHARGE
VOLTS
EastonPennsylvania
Module No.
StockModule Identification Plate
Service No.
Product
REFRIGERANT
R
C
AMPS
AMPS
DESIGNPRESSURE HIGH SIDE
MIN.BRANCHCIRCUIT AMPACITY
MAX.BRANCHCIRCUIT FUSE SIZE
MOTORCOMPRESSOR THERMALLYPROTECTED
FULLLOAD AMPS
R
SINGLE
PHASE
208264
NSF
U
LL
U
01034693R03
801 Church Lane • Easton, PA 18044, USA
Toll free [phone] • [phone]
www.follettice.com

2 Horizon 1650R/N Ice Machines

Horizon 1650R/N Ice Machines 3
Welcome to Follett Corporation ..................................................................................................................................4
Specications ...............................................................................................................................................................5
Operation.......................................................................................................................................................................7
Cleaning, weekly exterior care ..............................................................................................................................7
Cleaning, semi-annual evaporator cleaning..........................................................................................................7
Service.........................................................................................................................................................................12
Ice machine operation.........................................................................................................................................12
Water system.......................................................................................................................................................13
Electrical system .................................................................................................................................................14
Normal control board operation....................................................................................................................14
Test points ....................................................................................................................................................15
Error faults....................................................................................................................................................15
Hard errors ...................................................................................................................................................15
Soft errors.....................................................................................................................................................15
Relay output indication .................................................................................................................................15
Compressor/refrigerant solenoid output.......................................................................................................15
Wiring diagram, evaporator unit ...................................................................................................................16
Wiring diagram, condenser unit ...................................................................................................................17
Gearmotor data ............................................................................................................................................17
Mechanical system..............................................................................................................................................18
Evaporator disassembly ...............................................................................................................................18
Evaporator reassembly.................................................................................................................................20
Refrigeration system ...........................................................................................................................................23
Condenser unit operation.............................................................................................................................23
Refrigerant pressure data.............................................................................................................................23
Refrigerant charges......................................................................................................................................23
Refrigeration system diagram.......................................................................................................................24
Refrigerant replacement requirements.........................................................................................................25
Evacuation....................................................................................................................................................25
Ambients (evaporator unit) ...........................................................................................................................25
Ice capacity test ...........................................................................................................................................25
Bin full detection system .....................................................................................................................................26
Troubleshooting ...................................................................................................................................................27
Replacement parts..............................................................................................................................................30
Table of contents

4 Horizon 1650R/N Ice Machines
Welcome to Follett
Follett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding
after-the-sale support. To ensure that this equipment delivers the same degree of service, we ask that you review
the installation manual (provided as a separate document) before beginning to install the unit. Our instructions are
designed to help you achieve a trouble-free installation. Should you have any questions or require technical help at
any time, please call our technical service group at [phone] or +1(610)252-7301.
Before you begin
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage
is found, notify the shipper immediately and contact Follett Corporation so that we can help in the ling of a claim, if
necessary.
Check your paperwork to determine which model you have. Follett model numbers are designed to provide information
about the type and capacity of Follett equipment. Following is an explanation of the different model numbers in the 1650
series.
Chewblet®Ice Machine Model Number Configurations
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
R B SD 1650HC
MC Maestro™
Chewblet
(400 Series)
HC Horizon™
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro
Chewblet
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote.
If remote unit, high side is
208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
Icemaker Voltage Series Condenser
V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
M Ice Manager™
diverter valve
system
400 up to
454 lb
(206 kg)
1000 up to
1036 lb
(471 kg)
1400 up to
1450 lb
(658 kg)
1650 up to
1580 lb
(717 kg)
Application Configuration
S RIDE®
(RIDE remote
ice delivery
equipment)
T Top-mount
CAUTION
• Moving parts. Do not operate with front cover removed.
• Hot parts. Do not operate with cover removed.
• To reduce risk of shock, disconnect power before servicing.
• Most ice machine cleaners contain citric or phosphoric acid, which can cause skin irritation. Read caution
label on product and follow instructions carefully.
• Ice is slippery. Maintain counters and oors around dispenser in a clean and ice-free condition.
• Ice is food. Follow recommended cleaning instructions to maintain cleanliness of delivered ice.

Horizon 1650R/N Ice Machines 5
Specications
Electrical
Separate circuit and equipment ground required.
Evaporator unit
Standard electrical – 115/60/1
Maximum fuse – 15A
Amperage – 6A
Condensing unit
Single-Phase 3-Phase
Electrical 208-230 V, 6 0Hz 208-230 V, 60 Hz
Maximum Circuit HVACR breaker size 50A 35A
Minimum Circuit Ampacity 29.9A 21.2A
Evaporator plumbing
3/8" OD push-in water inlet
3/4" MPT
Notes: 3/4" vented drain line must slope a minimum of 1/4" per ft (6mm per 30.4 cm run).
Drain to be hard piped and insulated.
Water shut-off recommended within 10 ft (3 m).
Follett recommends installation of Follett water lter system (P/N 00130286) in ice machine
inlet water line.
Ambient
Evaporator unit
Air temperature 100 F/38 C max. 50 F/10 C min.
Water temperature 90 F/32 C max. 45 F/7 C min.
Water pressure 70 psi max. (483 kPa) 10 psi min. (69 kPa)
Condenser unit
Air temperature 120 F/49 C max. -20 F/-29 C min.
Refrigeration
3/8" liquid line – insulated
7/8" suction line – insulated
Note: Rack system installations require a capacity of 13,000 BTU/hr at 0 F (-18 C) evaporator temperature.
Evaporator pressure regulator (not supplied) is required.
Weight Ice production
Evaporator unit
190 lb (88 kg)
Condenser unit
Single-phase: 390 lb (177 kg)
3-phase: 340 lb (154 kg)
F
C
50
10
60
16
70
21
80
27
90
32
60
16
1669
757
1596
724
1523
691
1440
653
1356
615
70
21
1580
717
1528
693
1474
669
1387
629
1298
589
80
27
1479
671
1451
658
1424
646
1332
604
1240
562
90
32
1422
645
1387
629
1350
612
1267
575
1183
537
100
38
1366
620
1310
594
1254
569
1191
540
1127
511
lbs
kg
lbs
kg
lbs
kg
lbs
kg
lbs
kg
Inlet Water Temperature F/C
Ambient Air Temperature F/C
Ice machine capacity/24 hrs.

6 Horizon 1650R/N Ice Machines
Dimensions and clearances
Entire front of ice machine must be clear of obstructions/connections to allow removal.
1" (26 mm) clearance above ice machine for service.
1" (26 mm) minimum clearance on sides.
Condensing Unit
36.25"
(921 mm) 25.5"
(648 mm)
26.08"
(662 mm)
Front View Side View Back View
3/8" OD push-in
water inlet
7/8" suction line
3/8" liquid line
Ice transport tube connection
19.3" (491mm)
2.5" (64mm)
15.69" (399mm)
2.53"
(65mm)
6.95"
(177mm)
14.47"
(368mm)
2.87
(73mm)
1.81
(46mm)
3/4" MPT drain
PSIG
THEUSA
MADEIN
OZ
PHASE
SINGLE
LOWSIDE
CHARGE
PART NO
RR
HZ
EastonPennsylvania
208264
AMPS
AMPS
VOLTS
SERIALNO
CORPORATION
MODEL
ServiceNo.
Product
ModuleNo.
REFRIGERANT
FULLLOAD AMPS
StockModule Identification Plate
DESIGNPRESSURE HIGH SIDE
MAX.BRANCHCIRCUIT FUSE SIZE
MIN.BRANCHCIRCUIT AMPACITY
MOTORCOMPRESSOR THERMALLYPROTECTED
C
NSF
ULUL
21.05" (535mm)
23.50"
(597mm)
21.28" (541mm) Air exhaust
both sides
23.77" (604mm)
G
L2
L1
NEMA 5-15
right angle

Horizon 1650R/N Ice Machines 7
Operation
Cleaning and preventive maintenance (all models)
Note: Do not use bleach to sanitize or clean the ice machine.
Preventive maintenance
Periodic cleaning of Follett’s ice machine system is required to ensure peak performance and delivery of clean,
sanitary ice. The recommended cleaning procedures that follow should be performed at least as frequently as
recommended, and more often if environmental conditions dictate.
Cleaning of the ice machine system, in most cases, should be performed by your facility’s maintenance staff or a
Follett authorized service agent. Regardless of who performs the cleaning, it is the operator’s responsibility to see
that this cleaning is performed according to the schedule below. Service problems resulting from lack of preventive
maintenance will not be covered under the Follett warranty.
Weekly exterior care
The exterior may be cleaned with a stainless cleaner such as 3M Stainless Steel Cleaner & Polish or equivalent.
Semi-annual evaporator cleaning (every 6 months)
WARNING
• Wear rubber gloves and safety goggles (and/or face shield) when handling ice machine cleaner or sanitizer.
CAUTION
• Use only Follett approved SafeCLEAN™ Cleaner (P/N 00132001) and NU-CALGON IMS-II SANITIZER.
• Do not mix Cleaner and Sanitizer solutions together.
• DO NOT USE BLEACH.
• It is a violation of Federal law to use these solutions in a manner inconsistent with their labeling.
• Read and understand all labels printed on packaging before use.
Note: Complete procedure for cleaning an sanitizing MUST be followed. Ice must be collected for
10 minutes before putting ice machine back into service.
Fig. 1
1. To clean – Remove cover. Press the CLEAN button. The
machine will drain. Wait for the LO WATER light to come
on (Fig. 1).
Note: For Ice Manager diverter valve application, refer
to manual 00175273 for ice machine and diverter valve
cleaning process.
LO WATER
CLE
AN

8 Horizon 1650R/N Ice Machines
Fig. 2
2. Mix 1 gallon (3.8 L) 120 F (49 C) water and
7 oz (198 g) (one 7 oz packet of Follett SafeCLEAN ice
machine cleaner, P/N 00132001). Locate cleaning cup.
Fill until HI WATER light comes on (Fig. 2).
Note: Do not use bleach to sanitize or clean the ice machine.
HI WATER
Fig. 3
3. Replace cover on cleaning cup. Wait until machine
restarts. Machine will clean, then ush 3 times in
approximately 12 minutes (Fig. 3).
12
Fig. 4
4. To sanitize – Press CLEAN button. The machine will
drain. Wait for LO WATER light to come on (Fig. 4).
LO WATER
N
A
E
L
C

Horizon 1650R/N Ice Machines 9
Fig. 5
5. Mix 1 gallon 120 F (49 C) water and 1.6 oz (48 ml)
NU-CALGON IMS-II SANITIZER. Fill until HI WATER
light comes on (Fig. 5).
Note: Do not use bleach to sanitize or clean the ice machine.
HI WATER
Fig. 6
6. Replace cover on cleaning cup. Wait until machine
restarts. Machine will sanitize, then ush 3 times in
approximately 12 minutes (Fig. 6).
12
Fig. 7
7. To clean transport tube – Press power switch OFF
(Fig.7).

10 Horizon 1650R/N Ice Machines
Fig. 8
8. Disconnect coupling as shown (Fig. 8).
Fig. 9
9. Using disposable food service grade gloves, insert dry
Sani-Sponge™ (kit P/N 00132068). Next, insert Sani-
Sponge soaked in Nu-Calgon IMS-II sanitizer solution.
Push both Sani-Sponges down ice transport tube with
supplied pusher tube (Fig. 9).
1
2
3
16"
(407mm)
Fig. 10
10. Remove and discard 16” (407 mm) pusher tube (Fig. 10).

Horizon 1650R/N Ice Machines 11
Fig. 11
11. Reconnect coupling. Press power switch ON. Ice pushes
Sani-Sponges through tube (Fig. 11).
Fig. 12
12. Place a sanitary (2 gallon or larger) container in bin
or dispenser to collect Sani-Sponges and ice for
10minutes. Collect 5.5 lb (3 kg) of ice from unit. Discard
ice and Sani-Sponges (Fig. 12).

12 Horizon 1650R/N Ice Machines
Service
Ice machine operation (all models)
Follett’s ice machine consists of ve distinct functional systems covered in detail as follows:
• Water system
• Electrical control system
• Mechanical assembly
• Refrigeration system
• Bin full
The Horizon ice machine overview
The Follett Horizon ice machine uses a horizontal, cylindrical evaporator to freeze water on its inner surface. The
refrigeration cycle is continuous; there is no batch cycle. The evaporator is ooded with water and the level is controlled
by sensors in a reservoir. A rotating auger (22 RPM) continuously scrapes ice from the inner wall of the evaporator. The
auger moves harvested ice through the evaporator into an ice extrusion canal. The ice is forced through a restrictive
nozzle that squeezes out the water and creates the Chewblet. The continuous extrusion process pushes the Chewblets
through a transport tube into a dispenser or bin.
A solid state PC board controls and monitors the functionality of the ice machine. In addition to sequencing electrical
components, the board monitors various operational parameters. A full complement of indicator lights allows visual
status of the machine's operation. Additionally, the PC board controls the self-ushing feature of the ice machine. The
evaporator water is periodically drained and replenished to remove minerals and sediment.
A unique “bin full” detection system is incorporated in the Horizon ice machine. A switch located at the ice discharge port
of the machine detects the position of the transport tube. When the bin lls up with ice, the transport tube moves out of
the normal running position, and the switch turns the ice maker off. A domed housing at the end of the transport tube
contains the ice extrusion loads during shut down.
water
inlet
auger
compression
nozzle
ice
transport
tube
Harvest system diagram

Horizon 1650R/N Ice Machines 13
Water system
The water level in the evaporator is controlled by a feed solenoid and level detecting sensors. Referencing the
diagram below, water sensing rods extend down into the reservoir at the end of the evaporator assembly. The system
works via electrical conductivity as follows:
One of the longest probes is a common. When water is between any of the other probes and the common, the PC
board will sense the activation. During normal operation, the water level rises and falls between the Normal High and
Normal Low sensors. As water is consumed to make ice, the level will fall until the Normal Low sensor is exposed,
triggering the water feed solenoid on. Water will ll until the Normal High sensor is activated.
Additional sensors are incorporated in the reservoir for alarm and cleaning/ushing conditions.
Note: The potable water dissolved solids content must be greater than 10 ppm for the water control system to
function properly. If using reverse osmosis water ltration system, ensure T.D.S level is greater than 10ppm.
Alarm LO
Normal HI
Common
Normal LO
Normal
operating
range
Water system diagram
Water level diagram

14 Horizon 1650R/N Ice Machines
Electrical system
Normal control board operation
The PC board indicator lights provide all the information necessary to determine the machine’s status. Green
indicator lights generally represent “go” or normal operation; Yellow indicators represent normal off conditions; Red
indicators generally represent alarm conditions, some of which will lock the machine off.
A green light labeled POWER indicates power to the machine. A ashing green light labeled CPU is normal and
indicates that the Central Processing Unit “heart beat” is working. All other normal operation status indicators are
covered as follows:
1. Ice machine is making ice.
2. Ice machine is not making ice.
3. Ice machine is not making ice.
1. Normal running.
2. Normal time delay. When the bin lls with ice, the LOW BIN
light goes out and the refrigeration and auger drive systems
immediately shut down. The TIME DELAY light comes on,
initiating the time delay period. When the time delay expires,
the machine will restart provided that the LOW BIN light is on.
3. Normal purge indicator. After a selected period of ice
making time has elapsed (1 or 2 hours), the ice machine will
automatically self-ush. The refrigeration system will shut
down but the gear motor will continue to run. After the ush is
complete the machine will rell and start without a time delay.
Ice machine disposition Operating conditions
ON OFF
Legend:
ON or OFF FLASHING
POWER LOW BIN AUGER ON REFRIG ON PURGE TIME DELAY CLEANING SERVICE HI AMPS DRAIN CLOG HI WATER CPU LO WATER
POWER LOW BIN AUGER ON REFRIG ON PURGE TIME DELAY CLEANING SERVICE HI AMPS DRAIN CLOG HI WATER CPU LO WATER
POWER LOW BIN AUGER ON REFRIG ON PURGE TIME DELAY CLEANING SERVICE HI AMPS DRAIN CLOG HI WATER CPU LO WATER

Horizon 1650R/N Ice Machines 15
Test points:
The Horizon PC board incorporates on-board test points that can be used to determine various electrical outputs.
The test point holes allow a standard probe to be inserted for quick voltage measurement.
Error faults:
The Horizon PC board monitors various operating parameters including high pressure, auger gearmotor amperage
limits, clogged drain, and high and low water alarm conditions. There are two types of errors namely “hard” or “soft”.
A hard error is one that shuts the machine off and will not allow restart until the reset button is pressed. Even cycling
power will not reset a hard error. A soft error can either be automatically reset should the condition rectify, or if power
is cycled. Should an error occur, consult the troubleshooting guide in this manual or a Follett service technician.
Note: there are two types of LO WATER and HI AMPS errors as listed below.
Soft errors:
HI AMPS: The PC board monitors the amperage of the auger motor. Should the gear motor experience current
draw above the 8.4 amps limit the machine will shut down and the TIME DELAY, HI AMP, and SERVICE LED’s will
be illuminated. After the time delay the machine will restart and the TIME DELAY, HI AMP, and SERVICE LED’s will
clear.
LO WATER: During operation, the water level cycles between the normal low and normal high sensors. Should the
water be shut off to a running machine, a soft error will occur. The error sequence is as follows: During operation,
the water level falls to the normal low sensor, and when it does the water feed solenoid is energized. If water is not
detected at the normal low sensor within 120 seconds, a soft error will occur. The machine will shut down, but the
water feed solenoid will remain energized. Should water return, it will ll to the normal low sensor and the machine
will resume normal operation. The error will clear automatically.
DRAIN CLOG: The drain clog sensor, located in the plastic drain pan behind the drain solenoid, will detect the
presence of water just below the top edge of the pan. If water does not properly ow out of the drain pan it will rise to
the sensor, especially during a self-ushing purge cycle.
Hard error:
HI AMPS:
1. “Two strikes” feature. If the gearmotor has a second HI AMP occurrence during the countdown period (6 hours
after a HI AMP time delay) a hard error will occur and the HI AMP and SERVICE LED’s will be illuminated.
2. No current. To prevent the refrigeration system from running without gearmotor rotation the PC board will indicate
HIGH AMP and SERVICE if the drive relay is energized and there is no current draw.
LO WATER:
1. There is a sensor in the water reservoir that reaches down to the very bottom. The machine will not start if water is
not present at this sensor.
2. A hard error will occur should water not be present within 60 seconds of power up or if the sensors are
disconnected or damaged.
Relay output indication:
Each relay on the board has an indicator light associated with its output. For example, when the relay for the water
feed solenoid is energized, the adjacent indicator light glows green.
Comp/Sol output:
The output for the compressor is labeled COMP/SOL.

16 Horizon 1650R/N Ice Machines
TP3
TP5
TP6
TP8
TP7
TP4
TP11
DRN
H2O
IN
H2O
J15
J14
J13
J16
WATER
INPUT
DRAIN
120Vac
20Watt20Watt
120Vac
FCV-2FCV-1
#32
#33
#30
#31
J8
J12
J11
N
J9
J10
DRV
FAN
SOL
COMP
CB1
#34
#3
#1 #2
M1
J6
K3
C NO
1/2hp Max
J2
J18
J17
SENSING
AMP
MOTOR
J5
J4
J7
L1
NOC
K1
J3
1
2
RESET
SWITCH
HI WATER (R)
CPU (G)
LO WATER (R)
TIME DELAY (Y)
DRAIN CLOG (R)
LO PRESS (R)
HI PRESS (R)
HI AMPS (R)
SERVICE (R)
CLEANING (Y)
REFRIG ON (G)
AUGER ON (G)
LOW BIN (G)
POWER (G)
PURGE (Y)
J21
CONTROL PC BOARD
J23J22 J24
1
1 1
1
J51
4 3 2 1
INPUT 2
OR
MAINT
PURGE
S2
MOM
CLEAN
S3
FULL
BIN
(CONTACT CLOSURE)
RETURN
+V
(3 WIRE)
-V
OUT (light on)
WATER LEVEL
COM DRAIN
CLOG
8
LE
7
LOW
LE
ALARM
4
LE
COM
3
LE
NORM
HIGH
6
NORM
LOW
2
LE LE
JUMPER
JUMPER
#22
#24
#23
FCV-3
20Watt
120Vac
REFRIG
J50
3 2 1
D15 D10
D6
D9
D5
BRN BLK BLU
P52
120Vac 60Hz
L1
GND
N
~
6Amp DRAW RUNNING
J52
GND
4
1
MAIN OFF/ON
240Vac / 20FLA
O I
S1
#21
#20 WHT
BLK
5 2
J34
J33
J32
J31
RED / YELLOW
ORANGE / BLACK
RED
GREEN
YELLOW
BLUE
ORANGE
GREEN
YELLOW
BLACK
RED
1
J1
2 3
ICE MANAGER
CONTROL
(OPTIONAL)
BLK RED
Wiring diagram, evaporator unitEvaporator unit wiring diagram
Gearmotor data (Brother) Resistance of windings
Gearmotor current 5.0A (nominal) 115 vac gearmotor (Brother) 1.7Ω
Locked rotor amps 15A

Horizon 1650R/N Ice Machines 17
POTENTIAL RELAY
5
2
COMPRESSOR EQUIPPED WITH AN INTERNAL OVERLOAD
PROTECTOR. ALLOW TIME FOR RESET.
USE COPPER CONDUCTORS ONLY.
FAN 2
L1
CRANK CASE
HEATER
COMPRESSOR
TERMINAL
CBLACK
COMPRESSOR
CONTACTOR T1
L1
T2
L2
COMPRESSOR
CONTACTOR
P1
HP LP
T3
L3
START
CAPACITOR
WITH BLEEDER
RESISTOR
4
6
1
L2 L3 T3T1 F1 F2
FC
IMPORTANT: FAN 1
SRRED
YELLOW RED
BLACK
YELLOW
RUN
CAPACITOR
COIL
DT
Single-phase condensing unit wiring diagram
3-phase condensing unit wiring diagram
FAN 2
L1
CRANK CASE
HEATER
COMPRESSOR
TERMINAL
C
S R
GRD
L1 T1
RED
YELLOW
BLACK
ICM402
3 PHASE
MONITOR
T1
L1
T2
L2
L3
L2
T3
T2
COMPRESSOR
CONTACTOR COIL
TERMINAL
BOARD P1
HP LP
T3
L3
L2 L3 T3T1 F1 F2
FFC
FAN 1
POWER SUPPLY
230-60-3
Y Y-
OUT
C115
VAC
230
VAC
L1 L2 L3
D.T.
A
TO "Y-OUT"
AT PHASE
MONITOR
A
TO "P1"
AT TERMINAL
BOARD
B
C
TO "L2"
AT TERMINAL
BOARD
TO "230 VAC"
AT PHASE
MONITOR
BTO "L1"
AT TERMINAL
BOARD
CTO "C"
AT PHASE
MONITOR

18 Horizon 1650R/N Ice Machines
Fig. 13
Mechanical system
Evaporator disassembly
1. Press PURGE button to purge evaporator, and then turn
power OFF.
2. Unscrew and remove stream divider as shown.
Fig. 14
3. Unplug and remove gearmotor as shown.
4. Remove all traces of petrol-gel from the auger shaft.
Fig. 15
5. Unscrew and disconnect transport tube from louvered
docking assembly.
6. Unplug sensor at the electrical box.
7. Remove vent tube from shuttle housing as shown.

Horizon 1650R/N Ice Machines 19
Fig. 16
8. Unscrew and disconnect transport tube from louvered
docking assembly.
9. Unplug sensor at the electrical box.
10. Remove vent tube from shuttle housing as shown.
Fig. 17
11. Remove and discard mating ring and seal.
12. Carefully remove auger.
Fig. 18
Evaporator reassembly
1. Remove and inspect O ring seal. Discard if damaged in
any way.
2. Clean O ring groove. Lubricate O ring with petrol-gel and
reinstall.

20 Horizon 1650R/N Ice Machines
Fig. 19
3. Press new mating ring into main housing as shown.
4. Lube the shaft with liquid soap in the area shown and
slip on seal and spring.
Note: Do not touch the sealing surfaces. Use cardboard disk to
install.
Lube
with soap
touch
Do not
Cardboard
disc
Fig. 20
5. Reinstall main housing as shown.
Fig. 21
6. Orient auger shaft with keyway in the upward position.
7. Force main housing into position against evaporator and
place 1/4" (7 mm) diameter Phillips screwdriver into hole
in the auger shaft.
8. Replace V-band clamp as shown.
9. Replace nut on V-band clamp and tighten.
10. Remove screwdriver.
removed for clarity
Note: Shuttle housing