Follett Horizon Elite H D710ABT Series User manual

01113307R05
Order parts online
www.follettice.com
H_D710ABT, H_E710ABT, H_C1010ABT, H_C1010WBT, H_E1010ABT, H_E1010WBT,
H_C1410ABT, H_C1410WBT, H_E1410ABT, H_E1410WBT,
(See model number congurator on page 2 for details.)
self-contained
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
Horizon Elite™Ice Machine Installation Instructions
to Ice Storage Bin Top-mount Applications

2Horizon 710/1010/1410 BIN • TOP-MOUNT
CAUTION!
§This appliance should be connected by a qualied person in accordance with applicable codes.
§If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
§Connect to potable water supply only.
§This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory,
or mental capabilities, or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children should be
supervised to ensure that they do not play with the appliance.
§This appliance is intended to be used for household and similar applications such as staff kitchen areas
in shops, offices and other working environments; farm houses and by clients in hotels, motels and other
residential type environments; bed and breakfast type environments; catering and similar non-retail
applications.
§WARNING! To avoid a hazard due to instability of the appliance, it must be xed in accordance with the
instructions.
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
425 up to
425 lbs
(193 kg)
710 up to
675 lbs
(306 kg)
1010 up to
1061 lbs
(482 kg)
1410 up to
1466 lbs
(665 kg)
1810 up to
1790 lbs
(812 kg)
2110 up to
2039 lbs
(925 kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager™
diverter valve
system
P Cornelius Profile
PR150
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(425 Series)
HC Horizon
Chewblet
(710, 1010, 1410,
1810, 2110
Series)
HM Horizon
Micro Chewblet™
HC 1810D SVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations

BIN • TOP-MOUNT Horizon 710/1010/1410 3
Contents
Unpack ............................................................................................................................................................................4
Unpack Ice Machine..................................................................................................................................................4
Site Preparation..............................................................................................................................................................5
Installation site requirements.....................................................................................................................................5
Docking Assembly Installation .....................................................................................................................................6
External Connections ....................................................................................................................................................7
Ice Transport Tube Installation...................................................................................................................................7
Air-cooled ice machines only.....................................................................................................................................8
Water-cooled ice machines only................................................................................................................................8
Internal Connections ...................................................................................................................................................10
Ice transport tube .................................................................................................................................................... 10
Potable water lines...................................................................................................................................................10
Power cord...............................................................................................................................................................10
Power cord...............................................................................................................................................................10
TDS switch............................................................................................................................................................... 11
Cooling Lines........................................................................................................................................................... 11
Ice transport tube .................................................................................................................................................... 11
Potable Water Line................................................................................................................................................... 11
Cooling lines and power ..........................................................................................................................................12
Power cord...............................................................................................................................................................12
Plate.........................................................................................................................................................................12
TDS switch...............................................................................................................................................................12
Front Cover ...................................................................................................................................................................13
Ice machine start up procedure .................................................................................................................................13
Before turning on power ..........................................................................................................................................13
After turning on power .............................................................................................................................................13

4Horizon 710/1010/1410 BIN • TOP-MOUNT
1. Unpack
Carefully unpack and inspect the contents of your Follett ice machine.
1.1 Unpack Ice Machine
7/16"
7/16"
➊➋➌
➍➎
➏➐
DO NOT TILT ICE MACHINE
TO ACCESS BOLTS!
COMPRESSOR DAMAGE
WILL RESULT

BIN • TOP-MOUNT Horizon 710/1010/1410 5
2. Site Preparation
Provide drainage, potable water supply and electrical power to within 6 feet (2m) of ice machine
in accordance with local and national codes. Outdoor installation is not recommended and will
void warranty.
2.1 Installation site requirements
➋➌➊
1/4"
1'
6-20
NEMA
H_C1410A/W
H_C1010A/W
6-15
NEMA
208 V –5% to 230 V +5%
1" Stand pipe/Drain
3/4" MPT x 1" slip
➍
3/4" barb x 3/4" FPT
2 ft. x 1" OD
silicone tubing
Minimum 8"
radius
➌
➍5-15
NEMA
H_D710A
3/8" chassis
drain must be
used
➍
Electrical ➊
WARNING!
§This appliance should be permanently connected by a qualied person in accordance with applicable codes.
§If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
H_C1010/1410(A/W)BT 208-230/60
Requires a 15A dedicated circuit.
H _ D710A BT 115 /6 0 (Requires a 15A circuit)
H _ E 710 AB T 115 /6 0 ‡
H_E1010/1410(A/W)HS 230/50‡H_E1400(A/W)HS 230/50/1-20‡
‡ H_E710A, H_E1010A/W requires 15A dedicated circuit 1.50 mm2wire, H_E1410A/W requires 20A dedicated circuit 4.00 mm2wire. Plug
must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.
Potable Water Supply ➋ (3/8" push-in connection, 3/8" OD tubing required)
10 psi to 70 psi (69 kpa to 483 kpa) 45 F to 90 F (7 C to 32 C)
§This equipment is to be installed with adequate backow protection to comply with applicable federal, state, and
local codes
Condenser water supply for water-cooled systems ➌ (1/4" FPT inlet, 1/4" FPT outlet)
10 psi min.; 150 psi max. (69 kpa min.; 1034 kpa max.)
20 F to 90 F (–7 C to 32 C)
1.5 gallons (5.68 liters) per minute
Drains: ➍ 3/4" Barb for silicone drain, 3/8" push-to-connect for chassis drain
Minimum 8” radius on silicone drain line. The drain line from the ice machine must have at least 1/4" per foot (6,4
mm/0,3 m) pitch

6Horizon 710/1010/1410 BIN • TOP-MOUNT
3. Docking Assembly Installation
WARNING!
§Prior to installing the docking assembly, ensure that the drain tting is oriented (right or left) correctly for your
installation.An optional straight drain tting is also supplied.You may need to remove the back panel of the
docking assembly in order to re-orient or change the drain tting. Replace back panel prior to mounting the
docking assembly.
§Docking station must be secured in accordance with these instructions to ensure ice machine stability.
§Ventilation openings in the docking station should be clear of obstruction. Failure to do so could result in
damage to equipment.
§Plug must be accessible after nal installation.
➋
➊
➌
➊
§Remove protective tape from gaskets.§Apply gaskets ➊.
§Install shuttle actuator ➋ through dispenser top
and secure with locking nut ➌.
§Mount docking assembly using two screws provided.

BIN • TOP-MOUNT Horizon 710/1010/1410 7
4. External Connections
4.1 Ice Transport Tube Installation
➋
➌
➊
Hot Water
160 F (71 C)
§Install supplied ice transport tube insulation.
§Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➊ before making
connection to ease assembly.
§Connect ice transport tube to coupling on docking station ➋.
§Connect ice transport tube to shuttle actuator ➌.

8Horizon 710/1010/1410 BIN • TOP-MOUNT
4.2 Air-cooled ice machines only 4.3 Water-cooled ice machines only
3/4" barb x 3/4" FPT
1" Stand pipe/Drain
2 ft. x 1" OD
silicone tubing
Minimum 8"
radius
➍
3/4" MPT x 1" slip
➎
➌
➋
➊
➏
➏
➌
➋
➐
➑
3/4" barb x 3/4" FPT
1" Stand pipe/Drain
2 ft. x 1" OD
silicone tubing
Minimum 8"
radius
3/4" MPT x 1" slip
➍
➎
➊
§Rough-in ice machine potable water supply ➊. 3/8"
push-in connection will be made at included shut-off
valve then at back of docking station into solenoid.
§Remove access panel if necessary ➋.
§Connect the silicone tubing to the ice machine 3/4"
drain barb ➌.
§Assemble the 3/4" barb x 3/4" FPT to the 3/4" MPT
x 1" slip. Connect the other end of the silicone
tubing to the 3/4" barb ➍.
§Connect the 1" slip tting to the 1" stand pipe/drain
➎.
Note: Minimum 8" radius on silicone drain line.
Drain line from the ice machine must have
at least 1/4" per foot pitch (6,4 mm/0,3 m).
§Apply Petrol-gel to barbed drain tting ➏
§Replace access panel.
§Rough-in ice machine potable water supply ➊.
3/8" push-in connection will be made at included
shut-off valve then at back of docking station into
solenoid.
§Remove access panel if necessary ➋.
§Connect the silicone tubing to the ice machine
3/4" drain barb ➌.
§Assemble the 3/4" barb x 3/4" FPT to the 3/4"
MPT x 1" slip. Connect the other end of the
silicone tubing to the 3/4" barb ➍.
§Connect the 1" slip tting to the 1" stand pipe/
drain ➎.
Note: Minimum 8" radius on silicone drain
line. Drain line from the ice machine
must have at least 1/4" per foot pitch
(6,4mm/0,3 m).
§Connect cooling water supply ➏and return ➐
§Apply Petrol-gel to barbed drain tting ➑
§Replace access panel.

BIN • TOP-MOUNT Horizon 710/1010/1410 9
Chassis drain plumbing - required
§Plug must be removed from John Guest tting.
§Route 3/8" drain tubing through knockout in back
of docking station and insert fully into John Guest
tting connection at the rear of the machine chassis.
Route other end of 3/8" drain tubing to drain.
§Drain must slope 1/4" inch per foot (6 mm per 30,4
cm).

10 Horizon 710/1010/1410 BIN • TOP-MOUNT
5. Internal Connections
Air-cooled ice machines – follow steps 5.1 through 5.5.
Water-cooled ice machines – follow steps 5.6 through 5.12.
5.1 Ice transport tube 5.2 Water solenoid, shut-off valve, and
potable water line options
➊
➋
5.2.1 If water solenoid is already mounted to
evaporator:
1. Insert potable water line into shut-off valve.
5.2.2 If this is an undercounter installation:
1. Mount water solenoid atop evaporator
and locate the shut-off valve inside the
machine. Insert potable water line into
shut-off valve.
5.2.3 If water solenoid is not mounted and
machine will not be installed undercounter:
1. Mount water solenoid to inside rear (upper
right corner) of docking assembly using
one screw.
2. Insert potable water line into shut-off
valve - locate the shut-off valve outside the
machine.
3. Insert outgoing line from shut-off valve into
push-in connection of water solenoid.
§Slide ice machine into docking assembly
ensuring that drain tube is fully seated on
barbed drain tting ➊.
§Insert ice transport tube all the way into coupling
and tighten nut rmly ➋.
5.3 Power cord 5.4 Power cord
§Remove twist tie.
§Carefully pass plug through opening and plug into
wall outlet.
§For H_E units, install a suitable plug.
§Position plate into opening and secure with
supplied screw.
WARNING!
Plate must be securely installed to ensure proper
equipment ground.

BIN • TOP-MOUNT Horizon 710/1010/1410 11
5.5 TDS switch 5.6 Cooling Lines
CLEANER FULL DRAIN CLOG HIGH PRES HIGH AMPS SERVICE
MAINT/CLEAN LOW WATER TIME DELAY SLEEP CYCLE MAKING ICE LOW BIN POWER ON
CLEAN
TDS
HIGH
LOW
In Out
§Set the TDS switch on the elctrical box.
–HIGH: for extended service life
–LOW: for low-scale water
§Install ice machine cooling water lines to docking
assembly.
5.7 Ice transport tube 5.8 Water solenoid, shut-off valve, and
potable water line options
➊
➋
5.8.1 If water solenoid is already mounted to
evaporator:
1. Insert potable water line into shut-off valve.
5.8.2 If this is an undercounter installation:
1. Mount water solenoid atop evaporator
and locate the shut-off valve inside the
machine. Insert potable water line into
shut-off valve.
5.8.3 If water solenoid is not mounted and
machine will not be installed undercounter:
1. Mount water solenoid to inside rear (upper
right corner) of docking assembly using
one screw.
2. Insert potable water line into shut-off
valve - locate the shut-off valve outside the
machine.
3. Insert outgoing line from shut-off valve into
push-in connection of water solenoid.
§Slide ice machine into docking assembly
ensuring that drain tube is fully seated on
barbed drain tting ➊.
§Insert ice transport tube into coupling and tighten
nut rmly ➋.

12 Horizon 710/1010/1410 BIN • TOP-MOUNT
5.9 Cooling lines and power 5.10 Power cord
➊
➋
§Connect cooling water lines to ice machine ➊.
(Water "Out" connects to water regulator.)
§Water valve is set at the factory. DO NOT remove
seal or adjust water valve ➋.
§Remove twist tie.
§Carefully pass plug through opening and plug into
wall outlet.
§For H_E units, install a suitable plug.
5.11 Plate 5.12 TDS switch
CLEANER FULL DRAIN CLOG HIGH PRES HIGH AMPS SERVICE
MAINT/CLEAN LOW WATER TIME DELAY SLEEP CYCLE MAKING ICE LOW BIN POWER ON
CLEAN
TDS
HIGH
LOW
§Position plate into opening and secure with supplied
screw.
WARNING!
Plate must be securely installed to ensure proper
equipment ground.
§Set the TDS switch on the elctrical box.
–HIGH: for extended service life
–LOW: for low-scale water

BIN • TOP-MOUNT Horizon 710/1010/1410 13
6. Front Cover
Install front cover to ice machine.
➋
➊
§Slide ice machine cover over machine, ensuring that
tabs on back of cover slip under louvers on back
of docking assembly ➊, then tighten two screws
through cover.
§Place front cover on machine ➋.
7. Ice machine start up procedure
The start-up procedure below is intended to ensure that ice machine is operating properly after installation has
been made. Check each item listed and call factory immediately for assistance if you experience problems with
unit.
NOTICE!
§Ice machine MUST be sanitized prior to operation!
§Consult Operation and Service Manual provided with ice machine for sanitizing instructions.
7.1 Before turning on power
1. Sanitize ice bin.
2. Turn on water to ice machine and check for leaks.
7.2 After turning on power
1. Turn on power switch and immediately press Clean switch to sanitize ice machine. At beginning of
sanitizing process, ice machine will purge all water. Check internal and external drain connections for
leaks.
2. After sanitizing process, ice machine will start. Conrm that gearmotor, fan motor and compressor start
immediately.
3. Check that ice begins to enter dispenser bin area within approximately 10 minutes.

14 Horizon 710/1010/1410 BIN • TOP-MOUNT

BIN • TOP-MOUNT Horizon 710/1010/1410 15

01113307R05
©Follett Products LLC 2/22
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
Maestro, Micro Chewblet, Vision, Harmony, Ice Manager, Horizon, Horizon Elite are trademarks of Follett Products LLC.
Chewblet, RIDE, Follett are registered trademarks of Follett Products LLC.