Follett Horizon Elite 2110 Series User manual

Horizon Elite™
remote 1810, 2110 series Chewblet® ice machine
Short form specification:
Ice machine to be a Follett® Horizon Elite ice machine model
______________ [Insert size/series,condenser type and installation/
mounting, from model number guide] capable of producing compressed
nugget ice using an ecient, sanitary horizontal evaporator/auger system
and delivering ice by a flexible wire reinforced transport tube to
ice storage bin, iceand water dispenser, ice and beverage dispenser,
drop‑in dispenser or Ice Manager™diverter valve system, slide‑out
evaporator with utility docking station, front‑mounted unit status display,
evaporator water inlet at harvest end with automatic flush while producing
ice, and semi‑automatic cleaning and sanitizing system, plus all the features
listed below and mounting/performance‑enhancing accessories checked.
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
1Independent third party studies. Contact Follett for details.
2Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice.
³ Refer to price list for additional warranty information.
Features
Horizon Elite
1810 series ‑ up to 1784 lb (810 kg) in 24 hours
2110 series ‑ up to 2039 lb (925 kg) in 24 hours
‑ automatically transport ice through a tube with RIDE®
technology from up to 75' (22.9 m) away
‑ chewable, compressed nugget ice is preferred over cubes¹
‑ Chewblet ice dispenses reliably from ice and
beveragedispensers
‑ available with approximately 1.00" (2.54 cm) long standard
Chewblet ice or optional 3/8" (0.95 cm) long Micro
Chewblet™ice
‑ quiet production without noisy harvest cycles
Revolutionary, scale inhibiting design
‑ produces ice that has 15% the TDS of the incoming water for
optimum dispensing and long life in drinks
‑ quarantines and regularly expels scale producing dissolved
solids to dramatically reduce scalebuildup
‑ increases time between descaling and reduces or eliminates
the need for expensive scale treatment
‑ saves 35% water compared to comparable cubers
‑ three phase models ENERGY STAR®certified
Durable, attractive ice machine
‑ regular bearing inspection or replacement is notrequired
‑ upgraded, easy‑to‑read LED operating status and
diagnosticdisplay
Designed with sanitation in mind
‑ Agion®silver‑based antimicrobial product protection of key
ice and water contact components²
‑ floatless, sealed design inhibits formation of biofilms
‑ semi‑automatic cleaning and sanitizing system
Warranty
‑ 3 years parts and labor, 5 years compressor parts³
Certifications
Model configurations
For use with
1
Install/
mount Condenser Evaporator
Item number
6
1810 series
Item number
6
2110 series
ice storage bin
top
mount
with 115/60/14, 5 HCD1810RBT HCD2110RBT
without 115/60/1 HCD1810NBT HCD2110NBT
RIDE with 115/60/14, 5 HCD1810RBS HCD2110RBS
without 115/60/1 HCD1810NBS HCD2110NBS
Follett Vision™
undercounter
ice and beverage
dispenser
RIDE
with 115/60/14, 5 HCD1810RVS HCD2110RVS
without 115/60/1 HCD1810NVS HCD2110NVS
Cornelius
PR150
undercounter ice
and beverage
dispenser²
RIDE
with 115/60/14, 5 HCD1810RPS HCD2110RPS
without 115/60/1 HCD1810NPS HCD2110NPS
countertop ice
and beverage
dispenser
(by others)
top
mount
3
with 115/60/14, 5 HCD1810RHT HCD2110RHT
without 115/60/1 HCD1810NHT HCD2110NHT
RIDE with 115/60/14, 5 HCD1810RHS HCD2110RHS
without 115/60/1 HCD1810NHS HCD2110NHS
drop-in dispenser
(by others) RIDE
with 115/60/14, 5 HCD1810RJS HCD2110RJS
without 115/60/1 HCD1810NJS HCD2110NJS
Ice Manager
diverter
valve system
RIDE
with 115/60/14, 5 HCD1810RMS HCD2110RMS
without 115/60/1 HCD1810NMS HCD2110NMS
¹ Ordered separately
² Not compatible with Micro Chewblet ice
³ Requires top kit (see page 5 for part number)
⁴ Condensing unit is 208-230/60/1
⁵ For three phase remote condensing unit, replace third character (D) with an F
e.g. HCF1810RBT
⁶ For Micro Chewblet ice, replace second character (C) with an M
e.g. HMD2110RBT

2
Form# 8180 Remote 1810, 2110 series ice machine
Specification, evaporator unit
Horizon Elite 1810 series Horizon Elite 2110 series
W1 Width 22.70" (57.7 cm)
Fits on 22.00" wide dispensers
22.70" (57.7 cm)
Fits on 22.00" wide dispensers
D1 Depth 23.70" (60.2 cm) 23.70" (60.2 cm)
H1 Height 22.50" (57.2 cm) 22.50" (57.2 cm)
Clearance top, left and right–1.00"(2.54 cm) top, left and right–1.00"(2.54 cm)
C1 Electrical
115 V/60/1
5 amps, requires dedicated
15 amp circuit,
6' (1.8 m) cord, NEMA 5‑15 plug
5 amps, requires dedicated
15 amp circuit,
6' (1.8 m) cord, NEMA 5‑15 plug
Operating power 368 W 368 W
C2 Ice transport tube see page 7 for details see page 7 for details
C3 Water inlet 3/8" OD push‑in water inlet –
internalconnection
3/8" OD push‑in water inlet –
internalconnection
C4 Drain 3/4" MPT, 1" drain required
see page 7 for details
3/4" MPT, 1" drain required
see page 7 for details
C5 Ice bin signal cord for Vision applications only for Vision applications only
C6 Liquid line 3/8" 3/8"
C7 Suction line 7/8" 7/8"
Air temperature 50 ‑100 F (10 ‑ 38 C) 50 ‑100 F (10 ‑ 38 C)
Water temperature 45 ‑ 90 F (7 ‑ 32 C) 45 ‑ 90 F (7 ‑ 32 C)
Potable water pressure 10 ‑ 70 psi (69 ‑ 483 kPa) 10 ‑ 70 psi (69 ‑ 483 kPa)
Ice production see ice production chart on page 8 see ice production chart on page 8
Energy consumption
90 F (32 C) air,
70 F (21C) water
single phase – 4.59 kWh
three phase – 3.33 kWh
per 100lb(45.4 kg) ice
single phase – 4.65 kWh
three phase – 2.93 kWh
per 100lb(45.4 kg) ice
Water consumption 12.4 gal (47 L) of potable water per 100lb
(45.4kg) ofice (per AHRI test standards).
13.9gal (53 L) at lowTDS flush setting.
12.4 gal (47 L) of potable water per 100lb
(45.4kg) ofice (per AHRI test standards).
13.9gal (53 L) at lowTDS flush setting.
Refrigerant R404a R404a
BTU/hr (Kcal/hr) at 0 F (‑18 C)
evaporator, 90 F (32C) ambient air
15,700 (3,956) 18,200 (4,586)
Rack systems EPR valve set point
EPR valve to be supplied by installer
0 F (‑18 C) 0 F (‑18 C)
Approximate ship weight 170 lb (77 kg) 175 lb (79 kg)
Approximate net weight 160 lb (73 kg) 165 lb (75 kg)
NOTE: For indoor use only. Outdoor installation of evaporator unit is not recommended and will void warranty.
Dimensional drawing
Accessories
Top kit for ice and beverage dispensers (page 5)
Water filters (refer to form# 9905)
Wall mount bracket (item# 00997098)
Ice machine stand, height‑adjustable (item# 00997080)
Timer to control one or two ice machines
(item# 00967265)
Longer ice transport tube, specify length: ___ ft/m in
5'/1.5 m increments (10'/3 m provided as standard for
RIDE models) (item#00174896)
Insulated 35' (10.7 m) refrigeration lines
(item#00977785) – (not pre‑charged) for 1810R
and2110R
SafeCLEAN Plus™ice machine cleaner
1 x 8 oz (237 ml) bottle(item#01147826)
6 x 8 oz (237 ml) bottles(item#01149954)
Carton of 24 x 8 oz (237 ml) bottles
(item#01149962)
SaniSponge™, 24 sanitary sponges (item# 01075431)
W1
D1
H1
C1
C1 C2
C7
C6
C3
C4
C5
Back View
22.00"
(55.9 cm)
22.69"
(57.6 cm)
2.73"
(6.93 cm)
2.28"
(5.79 cm) 6.04"
(15.34 cm)
19.59"
(49.76 cm)
16.00"
(40.64 cm)
L2
L1
G

3
Form# 8180
Remote 1810, 2110 series ice machine
Specification, condenser unit
Horizon Elite 1810 series Horizon Elite 2110 series
W1 Width 30.00" (76.2 cm) – all models 30.00" (76.2 cm) – all models
D1 Depth (hail guard included) 38.50" (97.8 cm) – all models 38.50" (97.8 cm) – all models
H1 Height 25.75" (65.4 cm) – all models 25.75" (65.4 cm) – all models
Electrical single phase – 208‑230/60/1
three phase – 208‑230/60/3
single phase – 208‑230/60/1
three phase – 208‑230/60/3
Operating power single phase – 6.0 kW
three phase – 3.6 kW
single phase – 6.2 kW
three phase – 4.6 kW
Minimum circuit ampacity single phase – 26.2 A
three phase – 15.7 A
single phase – 27.1 A
three phase – 19.9 A
Maximum circuit HVACR breaker size single phase – 45 A
three phase – 25 A
single phase – 45 A
three phase – 30 A
Outdoor condensing unit operating limits
(air temperature)
min ‑20 F (‑29 C)
max 120 F (49 C)
min ‑20 F (‑29 C)
max 120 F (49 C)
Maximum refrigerant line run length 75' (22.9 m) 75' (22.9 m)
Maximum line rise above evaporator 35' (10.7 m) 35' (10.7 m)
Evaporator mounting above condenser 15' (4.6 m) 15' (4.6 m)
Maximum refrigeration line drop without oiltrap 15' (4.6 m) 15' (4.6 m)
Refrigerant charge 14.5 lb required at installation 14.5 lb required at installation
Approximate ship weight 305 lb (138 kg) 305 lb (138 kg)
Approximate net weight 295 lb (134 kg) 295 lb (134 kg)
NOTE:
1. The entire liquid line should be insulated separately from the suction line.
W1
D1
H1
Dimensional drawing

4
Form# 8180 Remote 1810, 2110 series ice machine
1 – Locating the ice machine
Horizon Elite remote Chewblet ice machines allow top‑mounting or mounting in a base cabinet, on a wall or on a floor stand up to
75'(22.9 m) from the dispenser or ice bin with RIDE technology. In‑cabinet mounting (RIDE applications) require special attention to
service access, unit ventilation and ice tube runs (seepages 5‑7).
Top mounting – ice and beverage
dispensers (by others)
RIDE model – Follett low-profile
Vision and Cornelius PR150 ice and
beverage dispensers
Top mount on Follett ice storage bins
Important specifier notes Important specifier notes Important specifier notes
1. Dispenser must be compatible with nugget ice.
See page 5 for compatible ice and beverage
dispenser models and top kitnumbers.
2. Verify ceiling or soffit height to ensure sufficient
top clearance.
1. See page 5 for critical clearance requirements.
2. Ice transport tube ships with Vision ice and
beverage dispenser (Vision applications only).
3. Ice transport tube ships with Horizon Elite
icemachine for Cornelius dispensers.
1. See form# B300 for bin sizing.
2. Verify ceiling or soffit height to ensure topclearance.
3. Locate floor sink or grate and drains in front of
storage bin.
4. Do not position bin drain lines to block
Ice•DevIce™bin cart.
RIDE model – ice and beverage
dispensers (by others)
RIDE model – drop-in beverage
dispensers (by others) RIDE model – Follett ice storage bins
Important specifier notes Important specifier notes Important specifier notes
1. Dispenser must be compatible with nugget ice.
Compatible dispensers include Cornelius
DB/ED/DF150/175, Lancer 4500-22N, FS-16N
and FS-44N, Servend MD150/175/200/250
SV150/175/200/250 and Follett Symphony Plus™
110CM, as well as dispensers listed on page 5.
2. Coca-Cola Freestyle 7000 top kit HSF30SC. Top
adapter IC CODE 46412 and ice kit ICCode 46430
must also be ordered from Coca-Cola. Coca-Cola
Freestyle 7100 requires top adapter ICCode 46751
and ice kit IC Code 46430 only, and must be
ordered from Coca-Cola. Coca-Cola Freestyle 9100
requires top kit HSF26SC. Consult with Coca-Cola
and Follett to qualify application prior to ordering.
3. RIDE application is approved only for Pepsi Spire
3.0, 5.0 and 4.1 designed for top mount ice
machines and requires MSP24SC for 3.0 and
MSP30SC for 5.0 and 4.1, ordered separately. For
manual fill versions of PepsiSpire 3.0, 5.0 and 4.1,
contact factory.
4. See page 5-6 for critical clearance requirements.
1. Compatible with the following dispensers:
Cornelius 1522, 1722, 2323 and Lancer 2200,
2300, 23300.
2. Requires 12.00" (30.5 cm) of access space for
installation on transport tube side.
3. See page 5-6 for critical clearancerequirements.
1. See form# B300 for bin sizing.
2. Locate floor sink or grate and drains in front of
storage bin.
3. Do not position bin drain lines to block Ice•DevIce
bin cart.

5
Form# 8180
Remote 1810, 2110 series ice machine
1 – Locating the ice machine (continued)
Top mounting – compatible ice and beverage dispensers1
Manufacturer Model Number Width in (cm) Depth 2 in (cm) Height 3 in (cm) Top kit
Coca‑Cola dispensers
Freestyle 7000 30.10 (76.5) 33.11 (79.0) 47.00 (119.4) H22F30‑F 4, 5
Freestyle 7100 30.00 (76.2) 33.80 (85.8) 47.00 (119.4) H22F30‑F 4, 6
Freestyle 9000 25.50 (64.8) 35.50 (90.2) 73.75 (187.3) H22F24‑F 4, 7
Freestyle 9100 25.50 (64.8) 39.25 (99.7) 77.2 (196.2) H22F26‑F 4
Cornelius dispensers
DB/ED/DF 200 series 30.00 (76.2) 30.00 (76.2) 34.38 (87.3) H22C30‑F
DB/ED/DF 250 series 30.00 (76.2) 30.00 (76.2) 38.38 (97.5) H22C30‑F
DB/ED/DF 300 series 44.00 (111.8) 30.00 (76.2) 34.00 (86.4) H22C44‑(F or B) 8
FlavorFusion/Overload 30.00 (76.2) 30.70 (78.0) 39.38 (100.0) H22C30‑F‑FF
IDC215 30.00 (76.2) 30.70 (78.0) 39.38 (100.0) H22C30‑F‑IDC
IDC255 and Pro Fast Gate 30.00 (76.2) 30.70 (78.0) 36.38 (92.4) H22C30‑F‑IDC 9
Lancer dispensers
4500‑30N 30.00 (76.2) 30.50 (77.5) 36.50 (92.7) H22L30‑(F or B) 8
FS‑22N 22.00 (55.9) 30.50 (77.5) 42.13 (107.0) H22L22‑F
FS‑30N 30.00 (76.2) 30.50 (77.5) 42.13 (107.0) H22L30‑(F or B) 8
Bevariety 30.00 (76.2) 31.00 (78.7) 37.75 (95.9) H22L30‑F‑STP
Sensation 30" 30.00 (76.2) 31.00 (78.7) 38.25 (97.2) H22L30‑F‑STP
Sensation 44" 44.00 (111.8) 31.00 (78.7) 39.38 (100.0) H22L44‑F‑STP
Touchpoint 32.50 (82.55) 33.70 (85.6) 40.00 (101.6) H22L30‑F‑STP
Pepsi dispensers Spire 3.0 27.00 (68.6) 35.00 (88.9) 38.12 (96.8) H22P24‑F
Spire 5.0 / 4.1 30.50 (77.5) 36.00 (91.4) 42.75 (108.6) H22P30‑F
Servend dispensers MDH‑302 42.75 (108.6) 31.00 (78.7) 32.38 (82.2) H22S44‑(F or B) 8
MDH‑402 60.00 (152.4) 30.50 (77.5) 32.38 (82.2) H22S60‑(F or B) 8, 10
1All approved dispensers can be filled with a RIDE model Horizon Elite ice machine without a top kit except for Coca-Cola Freestyle 7000 and Pepsi Spire 3.0, 5.0 and 4.1, see page 4 for details.
2Requires minimum 0.50"(1.27 cm) clearance between back of dispenser and wall.
3Net height after installation of top kit (excluding height of ice machine).
4Consult with Coca-Cola and Follett to qualify application prior to ordering.
5 Top adapter IC Code 46412 and ice kit IC Code 46430 must also be ordered from Coca-Cola.
6Top adapter IC Code 46753 and ice kit IC Code 46430 must also be ordered from Coca-Cola.
7 Adapter must also be ordered from Coca-Cola. KO IC Code: 46010 (Silver), 46011 (Red) or 46012 (Black).
8 Specify “F” for front facing, or ”B“ for backward facing units.
9Contact factory regarding IDC Pro.
10 60-inch models: Please specify number of Horizon Elite ice machines and location. D = 2; R = 1 on right side; L = 1 on left side.

6
Form# 8180 Remote 1810, 2110 series ice machine
3 – Horizon Elite ice machine mounting accessories
Optional wall mount bracket Optional machine stand Important specifier notes
22.00"
(55.9 cm)
25.50"
(64.8 cm)
23.00"
(58.4 cm)
AC
D
B
6.88"
(17.5 cm)
A- 15.875" (40.3 cm)
B- 19.375" (49.2 cm) C- 13.00" (33.0 cm)
D- 21.00" (53.3 cm)
1. For secure wall mounting, specify optional
wall mount bracket.
2. Wall and fasteners must support the weight
of the ice machine, bracket, supply water and
ice. Use of a backing board may be required
with hollow wall construction.
3. Machine stand mounting adds 6.88" (17.5cm)
to height of ice machine.
4. No dips in tube routing allowed.
5. Ice transport tube needs minimum 1/4"
per foot (2 cm per meter) pitch toward ice
machine and should be secured to prevent
dips and traps from forming.
2 – Undercounter/in-cabinet mounting
Cabinet details
Important specifier notes
Cabinet base
must be flat and free of obstructions
(no lip or utilities to block removal)
Cabinet door opening
24.00"W x 23.5"H
(60.9 cm x 59.7 cm) minimum
slides
out
Ice transport tube
secure to prevent dips
and traps from forming
12.00" (30.5 cm) minimum
between ice machine
and dispenser
minimum 1/4" per foot
(2 cm per meter)
pitch toward ice machine
1. Cabinet door opening must meet
minimum size requirements shown
and be free of obstructions to allow
ice machine to slide out (no lip or
utilities to block removal).
2. Cabinet base must be capable
of supporting ice machine and
allow ice machine to rest flat on
cabinetbottom.
3. No counter supports, electric or
plumbing can run in front of the
icemachine.

7
Form# 8180
Remote 1810, 2110 series ice machine
5 – Horizon Elite ice tube runs - specifier guidelines
Long tube runs for RIDE remote ice delivery equipment
1/4"
1'
maximum
2' (60.9 cm)
beverage
dispenser
wall-mounted
ice machine
support
straps
transport tube slope
(toward ice machine)
(2 cm per meter)
minimum of
6.00" (15.24 cm)
turn/corner
radius
ice transport tube –
1 3/16" OD,
2 1/8" OD with insulation
Important specifier notes
1. 75' (22.9 m) maximum ice transport tuberun.
2. Tubing routing bends must have a
6.00"(15.24 cm) radius or larger.
3. Dips and traps are not allowed. If not
supported from underneath, secure insulated
ice transport tube at least every2' (60.9 cm)
to prevent drips andtraps.
4. Relative humidity levels above 80% in areas
where the ice machine or ice transport tube is
located may produce excessive condensation
that will cause water damage.
5.
Contact factory for recommendations on
running tubing through a decorative soffit
orchase.
4 – Horizon Elite drain - specifier guidelines
Flush drain plumbing – For regular machine drainage Important specifier notes: Where code
allows, follow recommendation below.
➌
➊
3/4" barb x 3/4" FPT
1" Stand pipe/drain
2 ft x 1" OD
silicone tubing
Minimum 8"
radius
3/4" MPT x 1" slip
➋
1. Connect the silicone tubing to the ice machine 3/4"
drainbarb ➊.
2. Assemble the 3/4" barb x 3/4" FPT to the 3/4" MPT x
1"slip. Connect the other end of the silicone tubing to
the 3/4" barb ➋.
3. Connect the 1" slip fitting to the 1" stand pipe/drain ➌.
Note: Minimum 8" radius on silicone drain line. Drain line
from the ice machine must have at least 1/4" per foot
pitch (6.4 mm/0.3 m).
Note: Stand pipe/drain provided by others. All other
components provided with ice machine.
Chassis drain plumbing – To assist with condensate in high humidity areas Important specifier notes: Where code
allows, follow recommendation below.
1. Plug must be removed from John Guest fitting.
2. Route 3/8" drain tubing through knockout in back of
docking station and insert fully into John Guest fitting
connection at the rear of the machine chassis. Route
other end of 3/8” drain tubing to drain.
3. Drain must slope 1/4" inch per foot ( 6 mm per 30.4 cm).

Remote 1810, 2110 series ice machine
801 Church Lane | Easton, PA 18040, USA
1.800.523.9361 | 1.610.252.7301 | follettice.com
8180‑202009 | © Follett Products, LLC
Ice production – Horizon Elite 1810 series
Inlet water
temperature
F (C)
Ambient air temperature F (C)
60 (16) 70 (21) 80 (27) 90 (32) 100 (38)
lb (kg) production in 24 hr
50 F (10 C) 1859 (844) 1784 (810) 1685 (765) 1616 (734) 1500 (681)
60 F (16 C) 1723 (782) 1684 (765) 1578 (716) 1563 (710) 1409 (640)
70 F (21 C) 1620 (735) 1594 (724) 1514 (687) 1420 (645) 1319 (599)
80 F (27 C) 1550 (704) 1487 (675) 1485 (674) 1351 (613) 1299 (590)
90 F (32 C) 1471 (668) 1435 (651) 1370 (622) 1285 (583) 1207 (548)
Ice production – Horizon Elite 2110 series
Inlet water
temperature
F (C)
Ambient air temperature F (C)
60 (16) 70 (21) 80 (27) 90 (32) 100 (38)
lb (kg) production in 24 hr
50 F (10 C) 2039 (925) 2039 (925) 1934 (877) 1825 (828) 1703 (772)
60 F (16 C) 1943 (881) 1888 (856) 1878 (852) 1710 (776) 1584 (718)
70 F (21 C) 1833 (831) 1781 (808) 1789 (811) 1634 (741) 1489 (675)
80 F (27 C) 1754 (796) 1686 (765) 1643 (745) 1535 (696) 1426 (647)
90 F (32 C) 1650 (748) 1603 (727) 1577 (715) 1457 (661) 1395 (633)
ENERGY STAR and the ENERGY STAR mark are registered trademarks owned by the U.S. Environmental Protection Agency.
Agion is a registered trademark of Sciessent LLC.
HORIZON ELITE, ICE•DEVICE, ICE MANAGER, MICRO CHEWBLET, SAFECLEAN PLUS, SANISPONGE, SYMPHONY PLUS and VISION are trademarks of FollettProducts, LLC.
CHEWBLET, FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US.
Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin.
Remote condensing unit
Condensing unit installation specifications
Important specifier notes
air in
exhaust
48.00"
(121.9cm)
48.00"
(121.9cm)
24.00"
(61.0cm)
24.00"
(61.0cm)
36.00" (91.4 cm)
height clearance
1. Provide front, back, top and side clearances
asshown.
2. The maximum refrigerant line run length is
75' (22.9 m). Installations require 14.5 lb of
refrigerant.
3. The maximum line rise above the evaporator is
35' (10.7 m). Condensing unit above evaporator
unit – 35'(10.7m) (installations with rise over
20' (6.1 m) require additional suction line s-trap
at midpoint rise).
4. The evaporator can only be mounted a maximum
of 15' (4.6 m) above the condensing unit.
Note: The service loop is not included when
calculating length, rise or drop in the tubingrun.
Note: To connect evaporator/ice machine to rack systems, see page 3.