Follett Horizon HME1000ABT User manual

208264
StockModule Identification Plate
ServiceNo.
ModuleNo.
Product
REFRIGERANT
MODEL
MOTORCOMPRESSORTHERMALLYPROTECTED
EastonPennsylvania
FULLLOADAMPS
MAX.BRANCHCIRCUITFUSESIZE
MIN.BRANCHCIRCUITAMPACITY
DESIGNPRESSUREHIGHSIDE
AMPS
AMPS
VOLTS
CORPORATION
SERIALNO
PHASE
SINGLE
CHARGE
LOWSIDE
PARTNO
PSIG
THEUSA
MADEIN
OZ
R
C
R
HZ
UL
L
NSF
U
Order parts online
www.follettice.com
00159905R07
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com
Horizon™Ice Machine Installation Instructions
to Ice Storage Bin Top-mount Applications
HCC/HMC/HCE/HME1000ABT, HCC/HMC/HCE/HME1400ABT,
HCC/HMC/HCE/HME1000WBT, HCC/HMC/HCE/HME1400WBT,
(See model number congurator on page 2 for details.)
self-contained

2self-contained BIN • TOP-MOUNT
ConfigurationApplication
S RIDE™
(RIDE remote
ice delivery
equipment)
T Top-mount
400 up to
454 lbs
(206kg)
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
V Vision™
H Harmony™
B Ice storage bin
J Drop-in
M Ice Manager
diverter valve
system
CondenserSeriesVoltageIcemaker
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote. If remote
unit, high side is 208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
MC Maestro™
Chewblet®
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro Chewblet
HC 1400CSVA
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
Chewblet®Ice Machine Model Number Configurations

BIN • TOP-MOUNT self-contained 3
87
5 6
43
21
Read and complete the following 8 installation steps
Front coverInternal connection
External connection
Louvered docking assembly
Bin preparation
Site preparationUnpack
Ice transport tube

4self-contained BIN • TOP-MOUNT
Carefully unpack and inspect the contents of your Follett ice machine. 1
Unpack
1/2"
1/2"
➊➋
➌➍
➎➏
Unpack ice machine
1. 1

BIN • TOP-MOUNT self-contained 5
Prepare the installation site. 2
208264
StockModule Identification Plate
ServiceNo.
ModuleNo.
Product
REFRIGERANT
MODEL
MOTORCOMPRESSORTHERMALLY PROTECTED
EastonPennsylvania
FULLLOADAMPS
MAX.BRANCHCIRCUITFUSESIZE
MIN.BRANCHCIRCUITAMPACITY
DESIGNPRESSUREHIGHSIDE
AMPS
AMPS
VOLTS
CORPORA
TION
SERIALNO
PHASE
SINGLE
CHARGE
LOWSIDE
P
ARTNO
PSIG
THEUSA
MADEIN
OZ
R
C
R
HZ
U
L
L
NSF
U



NEMA
6-15
H_C1400A/W
H_C1000A/W
NEMA
6-20
1' (0,3m)
1/4" (6,4mm)
H_E1000A/W‡
H_E1400A/W‡
requires 15A circuit,
1.50 mm2wire
requires 20A circuit,
4.00 mm2wire
Site preparation
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of ice
machine in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
Electrical ➊
• H_C1000(A/W)BT 208-230/60/1-15 amps • H_C1400(A/W)BT 208-230/60/1-20 amps
• H_E1000(A/W)BT 230/50/1-15 amps‡• H_E1400(A/W)BT 230/50/1-20 amps‡
(H_E1000A/W requires 15A circuit, 1.50 mm2wire) (H_E1400A/W requires 20A circuit, 4.00 mm2wire)
‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45 to 90 F (7 to 32 C)
• Follett recommends the use of an in-line water ltration system (#00130286)
Condenser water supply for water-cooled systems ➌
• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)
• 45 to 90 F (7 to 32 C)
• 1.5 gallons per minute (5.68 liters per minute)
Drain ➍
• The drain line from the ice machine must have at least 1/4” per foot pitch (6,4mm/0,3m)
Installation site requirements
2.1

6self-contained BIN • TOP-MOUNT
Prepare the bin. 3
Bin preparation
• Remove protective tape from gaskets
Bin top preparation
3.1
➋
➊
➊
➌
• Apply gaskets
➊
• Install shuttle actuator ➋ through
dispenser top and secure with locking nut
➌
Bin top preparation
3.2

BIN • TOP-MOUNT self-contained 7
Louvered docking assembly 4
• Mount louvered docking assembly
Louvered docking assembly
4.1
Install the louvered docking assembly.
WARNING
• Docking station must be secured in accordance with these instructions to ensure ice machine
stability.
• Ventilation openings in the louvered docking station should be clear of obstruction

8self-contained BIN • TOP-MOUNT



Hot Water
160 F (71 C)
Ice transport tube
Install the ice transport tube. 5
• Install supplied ice transport tube insulation
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➊
before making connection to ease assembly
• Connect ice transport tube to coupling on louvered docking station ➋
• Connect ice transport tube to shuttle actuator ➌
5.1 Ice transport tube installation

BIN • TOP-MOUNT self-contained 9
Connect utilities to louvered docking assembly. 6
External connections
➊
➌
➋
➍
➋
➊
• Remove access panel if necessary
• Install drain line ➊.
The rigid drain line from the ice machine
must have at least 1/4" per foot pitch
(6,4mm/0,3m).
• Install ice machine potable water
supply ➋
• Replace access panel
Air-cooled ice machines only
• Remove access panel if necessary
• Install drain line ➊.
The rigid drain line from the ice machine
must have at least 1/4" per foot pitch.
• Connect cooling water supply ➋and
return ➌
• Install ice machine potable water
supply ➍
• Replace access panel
Water-cooled ice machines only
6.1 6.2

10 self-contained BIN • TOP-MOUNT
Connect louvered docking assembly to ice
machine. 7
Internal connections
Air-cooled ice machines – follow steps 7.1 through 7.4.
➊
➋
• Slide ice machine into louvered docking
assembly ➊
• Insert ice transport tube all the way into
coupling and tighten nut rmly ➋
Ice transport tube
7. 1
➊
➋
➊
➋
• Insert potable water line into valve ➊
• Push drain line over hose barb on
back of evaporator mount ➋
Potable water line
7. 2
• Position plate into opening and secure
with supplied screw
Power cord
7. 4
➊
• Remove twist tie
• Carefully pass plug thru opening and plug
into wall outlet
Power cord
7. 3
CAUTION
• Plug must be accessible after nal installation.
• H_E1400A/W 230/50/1 requires a 20A circuit (4.00 mm2wire)