Follett Horizon HCC1000ABT User manual

208264
StockModule Identification Plate
ServiceNo.
ModuleNo.
Product
REFRIGERANT
MODEL
MOTORCOMPRESSORTHERMALLYPROTECTED
EastonPennsylvania
FULLLOADAMPS
MAX.BRANCHCIRCUITFUSESIZE
MIN.BRANCHCIRCUITAMPACITY
DESIGNPRESSUREHIGHSIDE
AMPS
AMPS
VOLTS
CORPORATION
SERIALNO
PHASE
SINGLE
CHARGE
LOWSIDE
PARTNO
PSIG
THEUSA
MADEIN
OZ
R
C
R
HZ
UL
L
NSF
U
Order parts online
www.follettice.com
Horizon™Icemaker Installation Instructions
for Ice Storage Bin Top-mount Applications
HCC/HMC/HCE/HME1000ABT, HCC/HMC/HCE/HME1400ABT,
HCC/HMC/HCE/HME1000WBT, HCC/HMC/HCE/HME1400WBT
(See model number congurator on page 2 for details.)
self-contained
00182212R04
801 Church Lane • Easton, PA 18040, USA
Toll free [phone] • [phone]
www.follettice.com

2self-contained BIN • TOP-MOUNT
Chewblet®Ice Icemaker Model Number Configurations
A Air-cooled, self-contained
W Water-cooled, self-contained
R Air-cooled, remote condensing unit
N Air-cooled, no condensing unit for
connection to parallel rack system
A V SC 1000HC
MC Maestro
Chewblet
(400 Series)
HC Horizon
Chewblet
(1000, 1400,
1650 Series)
HM Horizon
Micro
Chewblet
C 208-230/60/1 (icemaking head)
Self-contained only.
D 115/60/1 (icemaking head)
Self-contained and remote.
If remote unit, high side is
208-230/60/1.
E 230/50/1 (icemaking head)
Self-contained only.
F 115/60/1 (icemaking head)
Remote only. High side is
208-230/60/3.
Icemaker Voltage Series Condenser
V Vision™
H Harmony™
B Ice storage
bin
J Drop-in
M Ice Manager™
diverter valve
system
400 up to
454 lbs
(206kg)
1000 up to
1036 lbs
(471kg)
1400 up to
1450 lbs
(658kg)
1650 up to
1580 lbs
(717kg)
S Satellite-fill™
T Top-mount
Application Configuration

BIN • TOP-MOUNT self-contained 3
Front cover
8
Internal connection
7
Ice transport tube
5
External connection
6
Louvered docking assembly
4
Bin preparation
3
Site preparation
2
Unpack
1
Read and complete the following 8 installation steps

4self-contained BIN • TOP-MOUNT
1/2"
1/2"
➊➋
➌➍
➎➏
Carefully unpack and inspect the contents of your Follett icemaker. 1
Unpack
Unpack icemaker
1. 1

BIN • TOP-MOUNT self-contained 5
Prepare the installation site. 2
208264
StockModule Identification Plate
ServiceNo.
ModuleNo.
Product
REFRIGERANT
MODEL
MOTORCOMPRESSORTHERMALLYPROTECTED
EastonPennsylvania
FULLLOADAMPS
MAX.BRANCHCIRCUITFUSESIZE
MIN.BRANCHCIRCUITAMPACITY
DESIGNPRESSUREHIGHSIDE
AMPS
AMPS
VOLTS
CORPORATION
SERIALNO
PHASE
SINGLE
CHARGE
LOWSIDE
PARTNO
PSIG
THEUSA
MADEIN
OZ
R
C
R
HZ
UL
L
NSF
U
1/4˝
1'
➍
➋
➌
➊NEMA
6-15
H_C1400A/W
H_C1000A/W
NEMA
6-20
H_E1000A/W ‡
requires 15 amp circuit
1.50 mm2wire
H_E1400A/W ‡
requires 20 amp circuit
4.00 mm2wire
Site preparation
2.1
Provide drainage, water supply and electrical power to within 6 feet (2m) of
icemaker in accordance with local and national codes. Outdoor installation is
not recommended and will void warranty.
Electrical ➊
• H_C1000(A/W)HS 208-230/60/1-15 amps • H_C1400(A/W)HS 208-230/60/1-20 amps
• H_E1000(A/W)HS 230/50/1-15 amps‡• H_E1400(A/W)HS 230/50/1-20 amps‡
(H_E1000A/W Requires 15 amp circuit 1.50 mm2wire) (H_E1400A/W Requires 20 amp circuit 4.00 mm2wire)
‡ Plug must be provided by end user & must conform to standard EN 60 335-2-24 of the end destination.
Potable water supply ➋
• 10-70 psi (69-483kpa)
• 45 F to 90 F (7 C to 32 C)
• Follett recommends the use of an in-line water ltration system (item# 00130286)
Condenser water supply for water-cooled systems ➌
• 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.)
• 45 F to 90 F (7 C to 32 C)
• 1.5 gallons per minute (5.68 liters per minute)
Drain ➍
• The drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m)
Installation site requirements
2.1

6self-contained BIN • TOP-MOUNT
Prepare the bin. 3
Bin preparation
• Remove protective tape from
gaskets
Bin top preparation
3.1
➋
➊
➊
➌
• Apply gaskets
➊
• Install shuttle actuator ➋ through
dispenser top and secure with locking nut
➌
Bin top preparation
3.2

BIN • TOP-MOUNT self-contained 7
Install the louvered docking assembly.
Louvered docking assembly 4
• Mount louvered docking assembly
Louvered docking assembly
4.1
WARNING
• Docking station must be secured in accordance with these instructions to ensure icemaker stability.
• Ventilation openings in the louvered docking station should be clear of obstruction

8self-contained BIN • TOP-MOUNT
Ice transport tube
Install the ice transport tube. 5
• Install supplied ice transport tube insulation
• Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers ➊
before making connection to ease assembly
• Connect ice transport tube to coupling on louvered docking station ➋
• Connect ice transport tube to shuttle actuator ➌
Ice transport tube
➊
➋
➌
Hot Water
160 F (71 C)
5.1

BIN • TOP-MOUNT self-contained 9
Connect utilities to louvered docking assembly. 6
External connections
➊
➌
➋
➍
➋
➊
• Remove access panel if necessary
• Install drain line ➊
The rigid drain line from the icemaker
must have at least 1/4" per foot pitch
(6,4mm/0,3m)
• Install icemaker potable water supply ➋
• Replace access panel
Air-cooled icemakers only
• Remove access panel if necessary
• Install drain line ➊.
The rigid drain line from the icemaker
must have at least 1/4" per foot pitch.
• Connect cooling water supply ➋and
return ➌
• Install ice machine potable water
supply ➍
• Replace access panel
Water-cooled icemakers only
6.1 6.2

10 self-contained BIN • TOP-MOUNT
Connect icemaker to louvered docking assembly. 7
Internal connections
• Remove twist tie
• Carefully pass plug thru opening and plug
into wall outlet
Power cord
7. 3
➊
➋
• Slide icemaker into louvered docking
assembly ➊
• Insert ice transport tube all the way into
coupling and tighten nut rmly ➋
Ice transport tube
7. 1
➊
➋
➊
➋
• Insert potable water line into valve ➊
• Push drain line over hose barb on
back of evaporator mount ➋
Potable water and drain lines
7. 2
Air-cooled icemakers – follow steps 7.1 through 7.4.
• Position plate into opening and secure
with supplied screw.
Power cord
7. 4
CAUTION
• Plug must be accessible after nal installation.
• H_E1400A/W 230/50/1) requires a 20 amp circuit (4.00 mm2wire)