for Living Dayton User manual

Dayton Hard-top Gazebo
Model No. 088-1634-8
Toll-free: 1-877-483-6759
IMPORTANT: Please read this manual carefully before beginning assembly of this product.
Keep this manual for future reference.
Assembly Instructions

3
Caution! Always keep children under close supervision while they are playing near or in this product.
Keep pets away while setting up the gazebo.
Caution! Check municipal by-laws prior to setting up the gazebo.
Imported by Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8
Table of ContentsImportant Safety Instructions
Table of Contents 3
Important Safety Instructions 3
Package Contents 4
Assembly 5
Cleaning and Maintenance 17
Specifications 17
Warranty 18
Warning! To reduce the risk of serious injury, read the following safety instructions before
assembling and using the gazebo.
IMPORTANT: RETAIN FOR FUTURE REFERENCE, AND READ CAREFULLY.
• This product is intended for domestic outdoor use i.e. decorative and sunshade purposes only.
• Always place and assemble the gazebo on flat horizontal ground.
• Consult with your local governing authority / local municipal codes regarding installation of temporary
structures before assembly.
• Ensure there is enough clearance around the product. Before assembling the gazebo, make sure to leave
a distance of not less than 6' (1.8 m) from any structures or obstructions, such as fences, garages, houses,
overhanging branches, laundry lines, or electrical wires.
• Anchor the gazebo to the ground with stakes for added safety.
• The gazebo cannot be permanently attached to a concrete floor or platform. Do not assemble the gazebo on
sandy, muddy or loose soil, as stakes are not strong enough to anchor in these types of soil.
• If more than one gazebo is set up, keep a minimum distance of 10' (3 m) between the gazebos.
• Any assembly or maintenance of the gazebo must be carried out by adults only.
• Make sure there is sufficient manpower when assembling or moving the gazebo.
• Some parts may contain sharp edges. Wear protective gloves if necessary.
• Check all nuts and bolts periodically for tightness. If required, tighten them.
• Repairing and replacing parts should be done by a qualified technician.
• Always disassemble the gazebo before experiencing heavy wind conditions, as it is not designed to withstand
harsh weather, including high wind, rain, and snow. In these conditions it might tip over and could cause injury to
bystanders.
• Do not hang any weights on the roof frame.
• Do not climb onto the roof of the gazebo. Doing so may cause the gazebo to fall down, thereby resulting in
serious injury.
• During snow days, remove the snow at the top when the snow is thicker than 4" (10 cm).
• After a period of time, usually in 2–3 months, tighten all the bolts.
• After a few years, if the paint peels off, use paint of similar color. It is recommended to use outdoor paint.
• If the gazebo will not be used for a long period of time (e.g. during winter time), disassemble and store it in a
clean, dry environment.
• Retain the original packaging to store the gazebo.
Made in China

Assembly
Caution!
• Proper placement of your gazebo is essential. Do not place the gazebo underneath
electrical lines.
• Keep children under close supervision while they are playing around this product. This
product contains small parts which can be swallowed by children.
• Keep fingers away from places where they can be pinched or trapped.
• Do not attempt to assemble the gazebo if any part is missing.
Let us help you!
DO NOT RETURN YOUR PRODUCT TO THE STORE. CALL US FIRST!
1-877-483-6759
If you have questions regarding your product, require warranty assistance,
or have damaged or missing parts, please call our customer service toll-free helpline.
Contact us for assistance, we’re here to help.
IMPORTANT: Please read and understand this manual before any assembly. Before beginning assembly of the
product, make sure all parts are available. Compare parts with packaging contents list.
Take all parts from the box and position them on a clean floor. Remove all packing materials and place them back
into the box. Do not dispose of the packing materials until assembly is complete. Read each step carefully before
beginning any assembly and make sure you understand each step. If any part is missing, please call our toll-free
number for assistance 1-877-483-6759.
Needed for assembly:
Hammer Screwdriver Wrench Ladder 4 people
4 5
Product No. 088-1634-8
Package Contents
Post - 4
Top bar - 4
Corner connector - 4
Middle bar - 4
Top base - 4
Slanting bar - 4
Base - 4
Tracking tube - 4
Left top big panel - 4
Arc support - 8
Right top big panel - 4
Short left bar - 4
Left top small panel - 4
Short right bar - 4
Right top small panel - 4
Long bar - 4
M6x15 Bolt - 60
M6 Washer - 140
Wrench - 2
M6x15 Screw - 16
M8 Nut - 1
M6x35 Bolt - 48
Stake 8x180 - 8
M6 Nut - 8
M6x35 Screw - 8
Slanting bar cover - 4
Top plate connector - 1
1
2
3
4
16
5
17
6
18
7
19
8
20
9
21
10
A
B
C
D
E
F
G
H
I
11
12
Top plate cover - 1
Hook - 1
Base cover - 4
13
14
15

6 7
Product No. 088-1634-8
Assembly Assembly
Note: When using screws and nuts to assemble the product, always use a flat washer between the frames
and the screw and/or nut. This will protect the parts from wear and tear.
Step 1
Requires 2, 3, A, B
Step 2
Requires 2, 6, A, B
Insert the corner connector (3) into the top bar (2) and fasten them using bolt (A) and washer (B).
3
2A
2
6B
A B
Step 3
Requires 5, 12, A, B
Step 4
Requires 5, 3, A, B
5
12 A
5
A
3
Connect the tracking tube (6) to the top bar (2) using bolt (A) and washer (B).
Connect one end of the slanting bars (5) to the alternate holes of the top plate connector (12) using bolt (A) and
washer (B).
Connect the other end of the slanting bar (5) to the corner connector (3) using bolt (A) and washer (B).
A B
A B
A B

8 9
Product No. 088-1634-8
Step 5
Requires 4, 12, A, B
4
12
A
Connect one end of the middle bars (4) to remaining holes of the top plate connector (12) using bolts (A) and
washers (B).
Step 6
Requires 2, 4, A, B
4
A
2
Connect the other end of middle bar (4) to the top bar (2) using bolt (A) and washer (B).
A B
A B
Step 7
Requires 5, 8, 9, B, F, H
Step 8
Requires 5, 10, B, F, H
Connect the long bar (10) to the slanting bar (5) using bolt (F), washer (B) and nut (H).
5
H
10
10
F
Connect one end of the short left bars (8) and short right bars (9) to the slanting bar (5) using bolt (F), washer (B)
and nut (H).
F
H
98
5
F B H
Assembly
Assembly
F B H

10 11
Product No. 088-1634-8
Assembly Assembly
Step 9
Requires 2, 8, 9, A, B
Connect other end of the short left bars (8) and short right bars (9) to the top bar (2) using bolt (A) and washer (B).
9
8
A
2
A B
Step 10
Requires 12, 14
Step 11
Requires 18, 19, B, D
Insert and tightly screw the hook (14) into the hole of the top plate connector (12).
19
18 18
19
D
B D
Insert the left top big panel (18) and the right top big panel (19) into the corresponding grooves of the top bar.
Secure the big panels with the slanting bar using screw (D) and washer (B).
12
14
Step 12
Requires 13, 14, E
Fix the top plate cover (13) onto the hook (14). Secure the cover using nut (E).
E
14
13
E

12 13
Product No. 088-1634-8
Assembly Assembly
Step 14
Requires 5, 11, 13, B, I
Insert slanting bar cover (11) under top plate cover (13). Attach slanting bar cover (11) to slanting bar (5) using
screw (I) and washer (B).
B I
Step 16
Requires 1, 17, B, D
Attach the base (17) to the post (1) using screw (D) and washer (B).
Step 15
Requires 1, 15, 16
1
16
15
17
D
1
Insert the post (1) into the top base (16) and base cover (15).
B D
Step 13
Requires 20, 21, B, D
Insert the left top small panel (20) and the right top small panel (21) into the corresponding grooves of the top
bar. Secure the small panels with the slanting bar using screw (D) and washer (B).
20 D21
B D
11
5
I
13

14 15
Product No. 088-1634-8
Assembly
Assembly
Step 17
Requires 1, 3, A, B
Step 18
Requires 1, 16, B, F
Attach the corner connector (3) to the post (1) using bolt (A) and washer (B).
16
1
F
Attach the top base (16) to the post (1) using bolt (F) and washer (B).
3
1
A
A B
B F
Step 19
Requires 2, 7, B, F
Attach the arc support (7) to the top bar (2) and post using bolt (F) and washer (B).
2
F
7
B F
Step 20
Requires 15, 17, G
Move and hold base cover (15) upward so the base (17) can be anchored to the ground using the stakes (G). Then
put down the base cover. Repeat this step for every post until all four posts are anchored.
17
15
G
G

Cleaning and Maintenance
16 17
Product No. 088-1634-8
Assembly
• Do not use bleach, acid, or other abrasive cleaners on the roof panels.
• Steel components of garden accessories and furniture are coated with rust-inhibiting paint. However, due to
the nature of steel, surface oxidation (rusting) will occur if this protective coating is scratched. This is a natural
process. To minimize this condition, it is recommended that care be taken when assembling and handling the
product, in order to prevent the paint from being scratched. Surface rust can be removed easily by applying a little
common cooking oil. If surface oxidation (rusting) occurs and no measures are taken to correct it, the oxidation
may start dripping onto the assembly surface, which may cause rough stains that could be difficult to remove.
Caution!
• Check all screws and nuts periodically for tightness. Tighten them if required.
• Disassemble the gazebo in the reverse order of the assembly steps. Always disassemble
the gazebo completely. A partially disassembled gazebo is not stable enough to resist
wind and bad weather, and therefore can be damaged and/or cause damage.
Dimensions 8' x 8' x 8' 8"
2.44 x 2.44 x 2.65 m
Weight 158 lb 6 oz
72 kg
Specifications
Step 21
The gazebo is ready for use.

18 Product No. 088-1634-8
This For Living™product carries a one (1) year limited warranty against defects in workmanship and materials.
Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period,
when returned by the original purchaser with proof of purchase. This product is not guaranteed against wear
or breakage due to misuse and/or abuse.
Warranty