Forest garden Kempsford 8 x 6 Summer User manual

Kempsford 8' x 6’ Summer
Fixing Pack (SUM86FP) Not to Scale
KSHSL86
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE SCREWDRIVER SPIRIT LEVEL
TAPE MEASURE
HAMMER
MUST PRE DRILL
Tower Bolt Qty 1
(supplied with 6 x 20mm screws)
Barrel Bolt Qty 2
(supplied with own fixings)
Important :
Assembly of this
building requires
a minimum of two
adults.
SDR555X1645PT
Door Qty 2
B
SHARP KNIFE
FOR ROOFING FELT
3.5 x 30mm Screws Qty 3 (silver)
Z’ bracket
Qty 4
Hinge
Qty 4
Felt Tacks Qty 100
ISSUE 0415
Panel Pin Qty 98
70121150PAI62PT
Barge Board Qty 4
RSSH86BPPT
Back Panel Qty 1
RSSH86DPPT
Door Panel Qty 1
E
G
C
8X6SHEDFL
Floor Qty 2
D
RSS86PEV2PT
Plain End Qty 2
A
J
XT487272
487mm Glaze Qty 2
I
28120489PAII45PT
489mm Beading Qty 8
28120274PAII45PT
274mm Beading Qty 4
15120500PPT 500mm Beading Qty 4
S
W
V
T
240011308
OSB Roof Qty 2
40121650PPT
40x12x1650mm Strip Qty 2
28282294PPT
28x28x2294mm Batten Qty 3
R
F
28282400PPT
28x28x2400mm Batten Qty 4 40120504PNPT
504mm Notched
Strip.
Qty 2
40120747PPT
40x12x747mm Strip Qty 2
K
L
M
40121807PTR
40x12x1807mm Corner Strip Qty 4
40122400PPT
40x12x2400mm Strip Qty 1
40121230PPT
40x12x1230mm Door Strip Qty 1
N
Q
FELT
85014
Qty 1
4.0 x 50mm Screws Qty 29
30mm Nail Qty 62
PW1250500
1250mm Glaze Qty 2
XT872487
872mm Glaze Qty 2
H
Parts List
Y
U
28120874PAII45PT 874mm Beading Qty 4
15121220PPT
1220mm Beading Qty 4
Turn Button
Qty 3
BEADING
3.5 x 25mm Screws Qty 30
3.5 x 30mm Screws Qty 48
O
P
56121667PPT
56x12x1667mm Strip Qty 2
X
15120457PPT 4mm Beading Qty 2
IMPORTANT, RETAIN FOR FUTURE REFERENCE.
-READ CAREFULLY
Check all parts prior to assembly.
This building is pre-treated with a factory base coat for protection during
storage and transit. We recommend that you treat your new building as
soon as possible after assembly using a wood preservative treatment.
Apply in accordance with the manufacturers instructions.
- Timber is a natural material. It will shrink and swell as a result of
varying moisture content.
- Please keep all plastic bags and small parts away from children
- This product must be built on a solid level base.
- The roof of this building is not a load bearing structure.
Technical Help line: 0333 7777 089 8.30 am to 5.00 pm Monday to
Friday.
In line with your statutory rights, please check all parts prior to
assembly, as assembly of damaged parts may be deemed to be
acceptance and this may affect the remedies you are entitled to. If the
product is not constructed in accordance with the instructions, or is
altered in anyway (e.g. painted), the manufacturer cannot be held liable
for any resulting damage.
Forest Garden Ltd. Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB

24
1
V
D
V
I
E
U
A
3Position the four panels so that they sit on top of the floor as shown making sure that the
bottom board is overhanging the floor. Make sure that the panels are flush before fixing
them to each other using 3 x 50mm screws.
Place the sheets in to the door so that each sheet sits on the rebated frame. Place each piece of
beading on top of the sheets makings sure that everything is flush. Fix the beading in place
using Panel Pins.
(T) = 2 x Panel Pins (U) = 4 x Panel Pins (V) = 5 x Panel Pins
Place the two floor against each other and fix them together using 3x50mm screws through the
floor bearers. Make sure that both of the floor sections are level.
Place on a solid level base.
B C
A
H
Make sure the panels are tight and sat on the floor correctly before fixing each panel to the floor
using 50mm screws. Make sure that the screws are in line with the floor bearers.
(A) = 2 x 50mm screws (B) = 3 x 50mm screws ( C) = 3 x 50mm screws
T
B
C
A

5ISSUE 0114
8
6N
7
Place the two 1667mm Strips on both sides of the door entrance. Make sure that each strip is
tight and flush with the framing on the inside. Fix in place using 30mm nails.
From inside the building position the three strips shown to frame the entrance. Again make sure
that these are tight and flush with the entrance framing. Fix using 30mm nails.
( O) = 5 x 30mm nails (Q) = 5 x 30mm nails (N) = 4 x 30mm nails
Position the Corner Strips so that they are tight and cover up where the panels join. Fix each strip
in place using 4 x 25mm screws.
Place the 2294mm batten against the front and above the entrance. Fix this in place using 4 x
50mm screws. Make sure that the screws are positioned in line with the vertical framing on th
reverse of the panel.
Place the roof sheet on top of the three battens as shown. The two 2400mm battens
should be flush on the ends and one of them should be offset from the edge 20mm. Fix
the roof sheet to the batten using 10 x 30mm nails (spaced evenly).
Position the 2294mm batten between these spaced as shown and offset on each end
by 50mm. Fix using 9 x 30mm nails. (spaced evenly)
Repeat
Turn the roof sections over and fix a Z’ bracket to each end of the middle batten using a 25mm
screw for each.
Repeat
(II)
552mm
473mm
M
Q
(I)
L
K
F
K
20mm offset
50mm offset
L
L
Nails spaced in
roughly 300mm
intervals
ISSUE 0415
flush with top
O
Forest Garden Ltd. Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB

11
12
9
ATTENTION:
TAKE CARE
WHEN TRIMMING
THE ROOF FELT.
10
Unroll the felt and cut it into three equal lengths. Place each section so that they overlap at the
apex and overhang on the eaves by approximately 50mm. Fix the felt to the roof using felt nails
spaced in 150mm intervals along the edges and the seam. Make sure that the felt nails are
positioned so that each locates into the batten on the eaves.
Cut and fold the corners securing with a single felt nail.
Place the Barge Boards against the ends of the roof so that they meet at the apex and are flush
on all sides. Fix each board in place using 3 x 35mm screws.
Eaves
Place the 504mm notched pieces (S) into the bottom of the window openings so that they are
flush on all sides and fix each piece in place using 2 x 25mm screws.
Position a 1250mm piece of glazing into the window frame before adding the beading, starting
with the bottom 500mm piece and secure the beading to the framing using panel pins.
(V) = 6 x Panel Pins (W) = 4 x Panel Pins
Place the completed roof sections on to the building so that the short sides line up with the end
panels and the long edge is in line with the apex. Fix each roof section in place using 3 x 30mm
screws for each end and 2 x 30mm screws for the side.
Repeat for the opposite side making sure that both sections meet at the apex.
S
G
X
From the outside place the remaining beading against the bottom front of the glazing and fix in
place using 3 x panel pins for each.
Repeat
W
W
X
Y
J

ISSUE 0415
13
16
80mm
70mm
P
Position the doors in
to the door frame and
make sure that the
larger part of the
hinge is sat tight
against the framing
before fixing each
hinge with 3 x 35mm
screws.
The doors should be
positioned squarely
and open outwards
without obstruction.
Position the two
747mm strips
against the inside of
the doors so that
they overlap the gap
equally.
The bottom strip
should be offset
80mm from the
bottom of the door.
The top strip should
be in line with the top
of the door and
spaced roughly
70mm from the
bottom strip.
Fix each strip to the
left hand door using
3 x 25mm screws
14
20mm overhang
Top of door
From the inside
position a small
barrel bolt against
top and bottom of the
left hand door. Make
sure that the bolts
will close properly
and hold the door
securely. Fix in place
using the screws
provided.
Place and fix a turn
button to the left
hand door so that
when it’s in the
locked position it
holds the doors level.
Use a 30mm screw.
(silver)
15
E
Position two cranked hinges approximately 100mm from the top and bottom of the door frame.
Fix the smaller part of the hinge to the door using 2 x 35mm screws.
Repeat
Forest Garden Ltd. Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB

Maintenance.
- Regularly check all fixings and parts are secure.
- Visually check for wear and tear.
- Check your roof felt for tears and leaks.
Biocidal Product Regulation (EU 528/2012) Article 58 Information
This article contains timber treated with Celcure AC-500, incorporating biocidal products to give
protection against wood destroying insects & wood rotting fungi.
Contains: Basic copper carbonate (Copper (II) carbonate – Copper (II) hydroxide (1:1)), Boric acid,
Benzalkonium chloride.
Wear gloves when handling freshly treated wood. Avoid breathing dust when cutting treated or
untreated wood. Dispose of off-cuts responsibly – do not burn.
235cm
178cm
BASE FOOTPRINT
8ft
8ft
6ft
Jacob Evetts
On the outside fix a
turn button to the top
and bottom of the left
hand door again
making sure that in
the closed position
they hold the doors
level. Use a 30mm
screw. (silver)
Fix the large barrel
bolt across the top rail
making sure that the
bolt will hold the door
closed in its locked
position. Fix using the
screws provided.