Forest garden BCSHSL77 User manual

Fixing Pack (BCSHSL77FP) Not to Scale
BCSHSL77
REQUIRED TOOLS :
(NOT SUPPLIED)
POZI DRIVE SCREWDRIVER SPIRIT LEVEL
TAPE MEASURE
HAMMER
MUST PRE DRILL
Barrel Bolt Qty 2
(supplied with own fixings)
Important :
Assembly of this
building requires
a minimum of two
adults.
B
SHARP KNIFE
FOR ROOFING FELT
4.0 x 40mm Screws Qty 12
Handle
Qty 2
Felt Tacks Qty 130
Forest Garden Ltd. Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
ISSUE 0416
Panel Pin Qty 68
SCS88RHSPT
RH sideQty 1
SCS88LHSPT
LH Side Qty 1
E
D
L
SCS77BPPT
Back Panel Qty 2
J
SCS77FRPPT
Front Panel Qty 1
24121630PAII45PT 1630mm Beading Qty 4
H1
F1
E1
H
D1
W
X
FELT10
Felt Qty1
30mm Nail Qty 36
45281150PPT Batten 1150mm Qty 2
G1 24120562PAII45PT 520mm Beading Qty 4
24121589PAII45PT 1547mm Beading Qty 4
Turn Button
Qty 3
BEADING
4.0 x 30mm Screws Qty 109
CS77FL2PT
Floor 2 Qty 1
F
Xt1626554
1626mm Glaze Qty 2
LAMDR658X1790RHPT
RH Door Qty 1
LAMDR658X1790LHPT
LH Door Qty 1
CS77FL1PT
Floor 1 Qty 1
214011868A129
OSB Roof Sheet Qty 2 23837298AII1786
OSB Roof Sheet Qty 2
G
A
K
I
N
XT1545520
1545mm Glaze Qty 2
57571930PPT Batten 1930mm Qty 1
Profile
61572044MPPT Batten 2044mm Qty 2
120190823PAII68PT Barge Board 823mm Qty 2
45452128PAII8089PT Batten 2128mm Qty 1
Y
45452150PAI29PT Batten 2150mm Qty 2
Z
45280705PPTBatten 705mm Qty 2
45450160PPT
Block 160mm Qty 1
57121930PPT Cover Strip 1930mm Qty 2
80121180PPT Barge Board 1180mm Qty 2
57122056PPT Cover Strip 2056mm Qty 4
43121294PPT Strip 1295mm Qty 1
End
70450190PMPPT
Block (shaped) 200mm
Qty 2
P
Q
R
U
S
T
V
A1
24120554PAII45PT 554mm Beading Qty 4
70700215PRPT
Block 200mm Qty 2
C1
Profile
4.0 x 50mm Screws Qty 48
Hinge
Qty 4
4.0 x 70mm Screws 10
C
28280150PPT
Batten 150mm Qty 1
B1
45281295PPT Batten 1295mm Qty 1
45282075PPT Batten 2075mm Qty 2
O
M
4.0 x 30mm Screws Qty 11 (silver)
IMPORTANT, RETAIN FOR FUTURE REFERENCE.
READ CAREFULLY
Check all parts prior to assembly.
This building is pressure treated to ensure longevity and
protect against rot. This may leave colour variations, but
these will even out as the moisture content stabilises.
- Timber is a natural material. It will shrink and swell as a
result of varying moisture content.
- Please keep all plastic bags and small parts away from
children
- This product must be built on a solid level base.
- The roof of this building is not a load bearing structure.
Maintenance - Regularly check that all the screws and
fixings are secure.
Technical Help line: 0333 7777 089 8.30 am to 5.00 pm
Monday to Friday.
In line with your statutory rights, please check all parts prior
to assembly, as assembly of damaged parts may be
deemed to be acceptance and this may affect the remedies
you are entitled to. If the product is not constructed in
accordance with the instructions, or is altered in any way
(e.g. painted), the manufacturer cannot be held liable for
any resulting damage.
4.0 x 60mm Screws Qty 10
28281294 Batten 1294mm (drip strip) Qty 1
28280800 Batten 800mm (drip strip) Qty 2
I1
J1

24
13
Fix the 160mm block against the inside of the front panel so that the corners meet the angled
battens. Fix this in place using 2 x 70m screws.
Place the front panel between the side sections so that it is 1810mm from the floor level and the
eaves are in line with the shaped posts. Fix this into place using 2 x 70mm screws for each side.
Place the shaped 190mm blocks into the corners where the front panel and sides meet. Make sure
that these are offset 45mm. Fix each block in place using 2 x 70mm screws.
Place the two side sections against the back panels so that they are tight and flush, allowing room
on the opposite end for placement of the shaped batten. Fix each panel in place screwing from inside, through
the back panel’s frame, into the side’s using 3 x 50mm screws.
Fix a 2044 mm shaped batten (Q) to the end of each side panel using 4 x 50mm screws screwing through the
side panel first.
Make sure that all edges are flush.
12mm overhang
45mm
P
Q
Place the two floor sections together before sitting a back panel onto the floor so that the cladding overhangs
the floor. Each back panel should be positioned so that there is a 45mm offset from the sides as illustrated.
Place the 1930mm batten (P) against end of the back panel in the corner. This should be placed so that it is
flush with panel on all sides.
Fix the panels to the post using 3 x 50mm screws for each.
P
Flush
H
A
G
D
C1
A1
B
C
C
Q
Screw Positions
All the panels must be tight before securing them to the floor using 50mm screws.
Make sure that the screws locate into the bearers underneath.

5
Forest Garden Ltd. Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
8
6
7
O
Place the 2150mm battens so that they sit onto the blocks at the front and back of the building. Secure the
square end to the block, screwing down using 1 x 60mm screw and the shaped end to the panel with 1 x
60mm screw.
Place the 2128mm batten (S) so that the angled end sits flush against the front panel
and on top of the block. The shaped end should sit on the small block at the back and
be tight with the panels. Fix each end with 1 x 60mm screw screwing at an angle into
the panels.
D1
45mm
28mm
T
Offset 34mm
Place the block (D1) against the back of the building so that it fits flush between the two back panels and offset
34mm below the top of the panels. Fix using 2 x 50mm screws.
Place the two 215mm blocks in the top back corner of each panel, as sown, so that they each sit tight against
the block and the flush with the top batten so that there is a lip. Fix each 215mm block with 2 x 50mm screws
screwing down through the top of the panels.
S
A
Place the1294mm batten on top of the floor against the entrance and make sure that it is flush on all sides. Fix
this in place using 3 x 50mm screws.
Place and fix the drip strips above the doors and windows using 50mm screws. Position the strip above the
door so that it 10mm above the door entrance.
800mm Drip Strip use 2 x 50mm screws.
1294mm Drip Strip 3 x 50mm screws
I1
J1

11
12
9
10
Place the roof sheets on top of the building so that the battens you have previously fixed are on
the outside of the panels. The battens at the front of the building should overhang 27mm away
from the front of the panels. Fix each sheet in place using 30mm screws, spaced evenly, making
sure that each screw locates into the beams and panel frames.
Sheet (1) = 15 Sheet (2) = 16
Nails spaced in
roughly 300mm
intervals
I
From outside the summer house slot a 1545mm piece of glazing material into the recess so that
it butts up against the framing. Position the beading tight against this and the framework and
secure using panel pins.
(H1) = 5 x Panel Pins (G1) = 3 x Panel Pins
Place the 1930mm cover strips against the corners so that they cover the joins between where the
side and back panels meet. Position the 2056mm strips against each end of the door entrance
making sure that they are flush with the framing. To secure each strip in place use 4 x 30mm
screws.
Position the 1295mm strip against the bottom of the door entrance so that it is flush on all sides.
Fix using 3 x 30mm screws.
Place the roof sheet (L) onto a 705mm batten so the board is flush along the edge and has a
15mm offset at the one end as shown. Fix in place using 3 x 30mm nails
Place the roof sheet (K) onto of a 1150mm and a 2075mm batten. Make sure that the battens
are positioned as shown and the roof sheet is flush along the edges. Fix in place using 30mm
nails.
(U) = 4 x 30mm nails (V) = 7 x 30mm nails ( R) = 4 x 30mm nails
15mm
W
W
L
W
X
V
R
U
K
(2)
(1)
flush
36mm
2382mm
H1
G1

13
16
14
Forest Garden Ltd. Unit 288 Hartlebury Trading Estate, Hartlebury, Worcestershire, DY10 4JB
15
On the outside fix a
turn button to the top
and bottom of the left
hand door again
making sure that in
the closed position
they hold the doors
level. Use a 30mm
screw. (silver)
Position the handle
centrally on each door
as shown.
Mark the positions of
the holes before pre-
drillling and fixing l in
place using 4 x 30mm
screws. (silver)
Position the doors into the door frame and make sure that the larger part of the hinge is sat tight
against the framing before fixing each hinge with 2 x 30mm screws.
The doors should be positioned squarely and open outwards without obstruction.
Place a 1626mm piece of glaze into the front of the door. Place the pieces of beading on top of
this and tight against the door’s frame. Secure each piece of beading using panel pins.
(F1) = 3 x panel pins (E1) = 6 x panel pins
J
D2
F1
E1
F
Position the doors in
to the door frame
and make sure that
the larger part of the
hinge is sat tight
against the framing
before fixing each
hinge with 3 x
30mm screws.
The doors should
be positioned
squarely and open
outwards without
obstruction.
E
F
100mm

Maintenance.
- Regularly check all fixings and parts are secure.
- Visually check for wear and tear.
- Check your roof felt for tears and leaks.
Biocidal Product Regulation (EU 528/2012) Article 58 Information
This article contains timber treated with Celcure AC-500, incorporating biocidal products to give
protection against wood destroying insects & wood rotting fungi.
Contains: Basic copper carbonate (Copper (II) carbonate – Copper (II) hydroxide (1:1)), Boric acid,
Benzalkonium chloride.
Wear gloves when handling freshly treated wood. Avoid breathing dust when cutting treated or
untreated wood. Dispose of off-cuts responsibly – do not burn.
17
Unroll the felt and cut
into three equal
lengths.
Starting from the back
lay the three pieces of
roof felt across the top
of the roof so that they
each overlap and
overhang the sides by
approximately 50mm.
Fasten the sheets in
place using the felt
nails supplied spaced
in 150mm intervals.
Make sure that the
nails are positioned
above the battens
underneath the roof
sheets.
Place the 1130mm
barge boards against
the front of the roof
above each side
section. Place the
boards so that they
are in line with the
felt and flush with the
outside corners. Fix
each board in place
using 3 x 40mm
screws.
Position the two
shaped barge boards
against the front of
the building so that
they meet at the
apex and fix each in
place using 3 x
40mm screws.
From inside summer
house fix a barrel bolt
to the top and bottom
of the door using the
screws provided.
Mark the position
where the bolt hits the
framing above and
below the door and
drill a hole for the bolt
to locate into.
Fix a turn button
against the back of
the door so that it will
hold the doors closed
when you are inside
the building. Fix using
a 30mm screw.
(Silver)
18
19
ATTENTION:
TAKE CARE
WHEN TRIMMING
THE ROOF FELT.
2026mm
2026mm
1077mm
1342mm
1077mm
7ft
8ft
7ft
7ft
Z
Y