Forever Redwood MODERN FAT TMBER PERGOLA User manual

ASSEMBLY INSTRUCTIONS FOR THE
MODERN FAT TMBER PERGOLA
866.332.2403 (TOLL FREE); 7am –7pm Pacific Time, Monday-Saturday

P| 1
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
CONTENT OF BOXES
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Drawing
Description
Posts
Long Single Supports
Short Single Supports
Short Supports with
In-Between Blocking
Long Supports with
In-Between Blocking
In-Between Covers
Central Supports
Roof Panels
Ceiling Fan Base
If ordered
Curtain Rod Fascia’s
Curtain Rods
Boots
If ordered
Louver Extension Pole
Curtain Rod Bases
Standard, Gale Wind or Hurricane
Anchor Bases.
If ordered
Qty.
Will vary
Note: Part numbers in the Content of Boxes Table are for reference only. These do not match to the numbers marked on the parts sent.

P| 2
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
HARDWARE LIST
No.
A
B
C
D
E
F
G
H
I
J
Drawing
Description
3/8´´ X 3´´ Lag Bolts
(To attach the anchor bases to the posts).
3/8´´ X 8´´ Bolts
(To attach the single supports to the posts).
3/8´´X 4´´ Lag bolts
(To attach the single supports together).
3/8´´X 6´´ Lag Bolts
(To attach the supports with in-between blocking to the
single supports).
3/8´´ X 7 ¼´´ Bolts
(To attach the supports with in-between blocking to the
single supports).
3´´ Deck Screws
(To attach the in-between covers to the supports with in-
between blocking. / To attach the curtain rod bases to the
posts and to the supports. / To attach the boots to the
posts).
3/8´´X 12´´ Lag bolts
(To attach the central supports to the short supports).
5/16´´ X 3´´ Lag Bolts
(To attach the louvered panels to the long supports and to
the central supports).
3/8´´ X 7´´ Bolts
(To attach the ceiling fan base to the central support).
1 5/8´´ Deck Screws
(To attach the curtain bases to the posts).

P| 3
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DESCRIPTION
Posts
Long Single Supports
Short Single Supports
Short Supports with
In-Between Blocking
Long Supports with
In-Between Blocking
In-Between Covers
Central Supports
Louvered Panels
Ceiling Fan Base
Curtain Rod Fascia’s
Curtain Rods
Boots
Louver Extension Pole
Curtain Rod Bases
Anchors Bases
Note: Part numbers in the Drawing are for reference only. These do not match to the numbers marked on the parts sent.

P| 4
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
NOTE: In order to know where the post needs to be placed, check the numbers on them. If the post is not marked, then place the
single Supports on the ground to locate the markings for each post position and clearly set your bearings. (“Don´t attach yet, only
place them on the ground to begin with”).
Step1:Install the anchor base (15)with ½´´X4´´anchor bolts or lag bolts. Please see the “How to anchor your pergola document”
for all details. Set your post (1) in the saddle of the anchor bases (15). Drill a ø ¼´´ hole in the post prior to anchoring to facilitate
the ratcheting of the hardware. After that, use a 3/8´´ X 3´´ lag bolts (A) to attach each post to the its respective anchor base (15).
15
1
1
1
15
15
1
15
3/8´´ X 3´´ Lag Bolts

P| 5
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 2: Attach the short and the long single supports (2,3) to the posts with 3/8´´ X 8´´ bolts (B) with washers and nuts. After
that, use 3/8´´ X 4´´ lag bolts (C) with washers to attach the single supports together. Each part has a series of numbers that
indicate where to attach the part with the corresponding number.
Step 3: Put up the short supports with in-between blocking (4), into the post notches as shown and attach to the posts with the
single support bolts. After that, attach the short supports with in-between blocking to the short single supports, used 3/8´´ x 6´´
lag bolts (D) with washers. Each part has a series ofnumbers that indicate where to attach the part with the corresponding number.
3/8´´X 6´´ Lag Bolts
3/8´´ X 8´´ Bolt
3
2
4
3/8´´X 4´´ Lag bolts

P| 6
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 4: Attach the shorts supports with in-between blocking (4) to the short single supports (3) with 3/8´´ x 7 ¼´´ bolts (E). Each
part has a series of numbers that indicate where to attach the part with the corresponding number.
Step 5: Put up the long supports with in-between blocking (5), into the post notches as shown and attach to the posts with the
single support bolts. After that, attach the long supports with in-between blocking to the long single supports, used 3/8´´ x 6´´ lag
bolts (D) with washers. Each part has a series of numbers that indicate where to attach the part with the corresponding number.
3/8´´ X 7 ¼´´ Bolts
3/8´´X 6´´ Lag Bolts
5

P| 7
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 6: Attach the long supports with in-between blocking (5) to the long single supports (2) with 3/8´´ x 7 ¼´´ bolts (E). Each
part has a series of numbers that indicate where to attach the part with the corresponding number.
Step 7: Use 3´´ deck screws (F) to attach the in-between covers (6) to the supports with in-between blocking. Each part has a
series of numbers that indicate where to attach the part with the corresponding number.
3´´ Deck Screws
6
3/8´´ X 7 ¼´´ Bolts

P| 8
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 8: Use 3/8´´ x 12´´ lag bolts (G) with washers to attach the central supports (7) to the short supports. Each part has a series
of numbers that indicate where to attach the part with the corresponding number.
Step 9: Attach the roof panels (8) to the long supports and to the central supports with 5/16´´ x 3´´ lag bolts (H) with washers.
Each part has a series of numbers that indicate where to attach the part with the corresponding number.
7
5/16´´ x 3´´ Lag Bolts
3/8´´X 12´´ Lag bolts
8
7
7

P| 9
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 10: Use 3/8´´ x 7´´ bolts (I) to attach the ceiling fan base (9) to the central support. Each part has a series of numbers that
indicate where to attach the part with the corresponding number.
Step 11: Attach the curtain bases (14) to the posts with 1 5/8´´ deck screws (J). Each part has a series of numbers that indicate
where to attach the part with the corresponding number
9
3/8´´ X 7´´ Bolts
14
1 5/8´´ Deck Screws

P| 10
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 12: Attach the curtain rod fascias (10) to the post and supports with 3´´ deck screws (F). Each part has a series of numbers
that indicate where to attach the part with the corresponding number.
Step 13: Place the curtain rods (11) on the curtain rod bases.
10
10
3´´ Deck Screws
11
11

P| 11
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 14: Finally, use 3´´ deck screws (F) to attach the boots (12) to the post. Each part has a series of number’s that indicate
where to attach the part with the corresponding number.
This completes the Pergola assembly. Hope you enjoy your set for many decades. If you ever have a problem or a question,
don't hesitate to call us (866 332 2403) or email us. We are here to support you.
3´´ Deck Screws
12
12
12
12

P| 12
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
HOW TO REMOVE THE ELECTRICAL WIRING TRIM FROM THE POST:
Step 1: First remove the deck screws to remove the boots of the post.
Step 2: Remove the Curtain Rod Fascia of the Pergola.
Don´t add the lag bolt over
the trim piece initially.

P| 13
MODERN FAT TIMBER PERGOLA
www.ForeverRedwood.com
Step 3: Remove the trim.
Note: The dimensions of the trim are standard, adjust if necessary.