Breezesta PB-1600 User manual

PALM BEACH ARMLESS SECTIONAL
PB-1600
1 PB-1600 Assembly

B
A
a c b d
e
G
Please read entire instruction before beginning
g
f
C
E
D
F
FOR USE IF CONNECTING FURNITURE-SEE LAST
PAGE OF INSTRUCTIONS
Suggested Tools:
Drill, Mallet
PARTS
PART DESCRIPTION PART NO. QTY
A PB ARMLESS RH FRAME ASSEMBLY SA-00369 1
B PB ARMLESS LH FRAME ASSEMBLY SA-00370 1
C PB SLING SPACER ASSEMBLY SA-00382 1
D PB ARMLESS SEAT BACK SLAT PRT-00809 3
E FRONT/REAR SLING RAIL ASSEMBLY SA-00392 2
F PB ARMLESS FRONT BOTTOM SPREADER PRT-00812 1
G 24"X24" SEAT SLING H-0000-SLG 1
SA-00393 HARDWARE KIT
PART DESCRIPTION PART NO. QTY
a #8 X 1-1/4" TORX SCREW-PAINTED H-0000-S8125 12
b #8 X 1-3/4" TORX SCREW H-0000-S8175 12
c #8 X 2-1/2" TORX SCREW H-0000-S825 6
d LEVELING MOUNT H-0000-LM 4
e 6-INCH T20 TORX BIT H-0000-T20X6 1
f CONNECTOR PLATE H-0000-CP 2
g #8 X 1-1/4" TORX SCREW-UNPAINTED H-0000-S8125 8
2 PB-1600 Assembly

A
D
E
E
F
B
bb
2.
If you did not start with the slats on the floor,
carefully rotate the chair to its back. Align the
top back slot of assembly
B
with the top back
slat. Align the remaining slats and use a mallet
to start the slat tenons into the frame, leaving
them slightly out.
Insert the front and rear sling rails (
E
) and the
front bottom spreader (
F
) into their respective
slots. Then complete the process of seating the
back slats into the frames so all tenons fully
seated.
1.
Place Frame Assembly
A
on a flat
surface either as shown or with the slats on
the ground and frame sticking up in the
air. Insert the 3 Back Slats
D
into the slots of
the frame. This may require some tapping
with a mallet to set them firmly into the
slot.
The Back Slat tenon is offset, and is
positioned to the rear of the chair as seen
at right.
(2) 1-3/4" screws (
b
) on
each end of the rail
assemblies and spreader.
3.
Using the 6" torx bit (hardware
e
), screw the (12) 1-3/4" screws
(
b
) into the bottom spreader (
F
)
and sling rails (
E
). When tight, the
ends of the spreader and rails
should be flush to the two side
frame assemblies.
3 PB-1600 Assembly

bb
d
3.00 3.00
KEEP SLAT FLUSH WITH
TOP OF SEAT FRAME
a
6.
Insert sling spacer
C
into the seat
frame as shown at left. Be sure it is
pushed against the back of the seat.
Install (6) hardware
c
to hold it in place.
Insert the seat sling (
G
) into the seat
frame. It should drop into the frame with
minor pressure applied to the frame
sides.
5.
Screw in the back seat slats using (12)
hardware
a
. Start at the top, making sure
the top of the slat is flush to the top of the
chair frame. Then work your way down to
the remaining two slats. For reference,
slats are spaced 3" from the bottom of
one to the top of the next.
Optional:
If you wish to physically connect multiple pieces
of furniture together, use the included plates and 1-1/4" screws
(
f
&
g
) as shown at left. Connect plates to the inside faces of
the front and back legs allowing approximately 1-1/2" of the
plate to protrude from the side of the chair. Then move the
next furniture piece into place and fasten the plates to it.
E
C
c
G
f
g
4.
Before flipping the chair to it's feet,
install the (4) leveling mounts
(hardware
d
)
by threading them into the inserts located
at the four corners on the bottom of the
chair.
4 PB-1600 Assembly