Forza 1300 CTH Series User manual

1300 CTH-CTA
External Mechanical
puller Series
1300 CTH-CTA
User´s Manual

ÍNDEX
1. Technical features 3
2. 1300CTH puller dimensions with pump 3
3. 1300CTA puller dimensions 4
4. User instructions 4
5. Jaws correct position 5
6. Exploded view 6
Rev. 30.07.18

3
1. TECHNICAL FEATURES
• 2 or 3 jaws pullers.
• Normal jaws (2 holes), long jaws (3 holes), extralong jaws (4holes).
• External
• Forged jaws
2. 1300CTH PULLER DIMENSIONS WITH PUMP
Reference with L: long jaws, X: Extalong jaws
Reference F Tm A B Stroke Weigth
1306CTH 00806 6 300 310 √62 10,2
1306CLTH 00806 6 380 360 √62 11,2
1306CXTH 00806 6 460 410 √62 13,6
1308CTH 00808 8 370 425 - 82 19,5
1308CLTH 00808 8 485 480 - 82 21,5
1308CXTH 00808 8 600 540 - 82 23,5

4
3. 1300CTA PULLER DIMENSIONS
4. USER INSTRUCTIONS
1.Make sure that the spindle is perfectly clean and greased.
2. Check that the spindle is pointed. If it is not, place a point protector.
3. Make sure the legs are perfectly centered.
4. Turn the spindle in order to apply force. Never hit the spindle.
5. Do not keep the spindle too far out of the body.
6. Use all necessary personal protective equipment (PPE).
DO NOT USE POWER TOOLS
Reference A B max. B min. C Tm. Weigth
1306CTA 300 310 50 220 √6 14,0
1306CLTA 380 360 50 220 √6 15,0
1306CXTA 460 410 50 220 √6 16,0
1308CTA 370 425 70 205 - 8 19,5
1308CLTA 485 480 70 205 - 8 21,5
1308CXTA 600 540 70 205 - 8 23,5
• All the jaws at the same time.
• Offer easier positioning of the
puller even in difcult to get at
place.
• The self centering puller is safe
thanks to it´s jaw lock device in
max spread position.

5
5. JAWS CORRECT POSITION
It is advisable to place the jaws in the lowest possible hole. In this way, the jaws will be
less bended when applying great effort. (Figure 1)
As more height is needed the spindle starts to come out more (Figure 2). If the axis
is bigger, the spindle will come out in excess of the body, (Figure 3), in that case when
pulling with the wrench we can twist the spindle.
When the height of the spindle is very high, it is better to change the position of the
legs. (Figure 4).
Figure 1
Figure 2
Figure 3
Figure 4
This pullers can be assembled with normal legs (05), long legs (06) or
extra long legs (16).
The puller is stronger when the legs are in the lower holes position.
That position causes the legs to bend less when making large forces.
(Figure 1)
But if the spindle goes far above the body it can be bent when pulling
with the key. (gure 4). The spindle can seize up, when this type of
bending happens.
Choose carefully the position of the legs.

6
6. EXPLODED VIEW
1306CTH Exploded view 1308CTA Exploded view
Spindles
Ref. Ton. A B ØC D E ØF ØG ØH
00806 6 340 310 23 120 115 22 45 54
00808 8 360 310 23 155 115 22 50 60

7
Jaws
Pata extra larga 16
Pata larga
Pata corta
Ref jaw P R E L D Puller
131005 15 25 12,5 355 83 1306CTH
1306CTA
131006 15 25 12,5 436 83
131016 15 25 12,5 516 83
131705 15,5 32 16 435 115 1308CTH
1308CTA
131706 17,5 31 15,5 550 115
131716 17,5 31 15,5 665 115

S.L. de Herramientas Especiales Forza
C/ San Miguel de Atxa, 24
01010 Vitoria
www.forza.es