Forza 9300 Series User manual

9300 - 9300T - 9300K
Mechanical Puller
External 9300,
9300T series
and 9300K set
Manual

ÍNDEX
1. Technical features 3
2. Puller dimensions 3
3. User instructions 4
4. Jaws position 4
5. Point protector 6
6. Exploded view 6
7. 9300K Set 8
Rev. 25.02.21

3
1. TECHNICAL FEATURES
2 or 3 jaws puller.
External .
Forged jaws.
The point of the jaw is very thin in order to access to small places.
2. DIMENSIONS OF THE PULLER
2 jaws
3 jaws
Ref. A B a b C D Ton. Weigth
9300 60 40 40 54 1,5 4,5 0,5 0,2
9301 88 53 56 76 2,5 6 1 0,4
Ref. A B a b C D Ton. Weigth
9300T 85 100 40 54 2,5 6,0 0,5 0,4
9301T 85 100 56 76 2,5 6,0 1 0,7
2 and/or 3 jaws.

4
3. USER MANUAL
1. Make sure that the spindle is perfectly clean and greased.
2. Check if the axis is dotted. If it is not, place a point protector.
3. Make sure that the jaws / extenders are perfectly centred.
4. Apply extraction force by turning the spindle. Never hit the spindle.
5. Do not keep the spindle too far out of the body.
6. Use all the necessary personal protective equipment (PPE)
DO NOT USE POWER TOOLS
4. JAWS POSITION
These series of pullers can carry normal jaws either (05) or long jaws (06).
The puller is stronger when the jaws are located in the lower holes. That position causes the
jaws to bend less when making great forces. (Figure 1) However, if the spindle goes far above
the body, it can be bent when pulling with the key. (gure 4).
This type of bending can produce the spindle seizure.
Choose carefully the jaws position.
1 2

5
5. POINT PROTECTOR
Spindle with xed point (all models)
In the spindles with xed point it is necessary to place a hardened point protector when the
shaft is not dotted to protect the spindles of the pullers.
3 4
Protective point

6
6. EXPLODED VIEW
Body
Exploded view 2 short jaws Exploded view 3 short jaws
Jaws
spindles
Spindle with xed point. All the models
Ref. jaw Thread L X H Point Puller
130003 M8 x 1 90 12 9 Fix 9300 / 9300T
130103 M10 x 1 124 14 12 Fix 9301 / 9301T
Ref. jaw e E D L
930005 2 4,5 16 72
930105 2,5 6 22 110

7
7. 9300K SET
Pullers that can be assembled:
Ref. Jaws A B a b C D Ton. Weigth
9300 2 60 40 40 54 1,5 4,5 0,5 0,2
9301 2 88 53 56 76 2,5 6 1 0,4
Ref. Jaws A B a b C D Ton. Weigth
9300T 3 85 100 40 54 2,5 6,0 0,5 0,4
9301T 3 85 100 56 76 2,5 6,0 1 0,7

S.L. de Herramientas Especiales Forza
C/ San Miguel de Atxa, 24
01010 Vitoria
www.forza.es