Forza 1300 Series User manual

1300
External
mechanical puller
1300 series
User´s Manual

Revisado 13.07.18

ÍNDICE
1. Tecnhical features 4
2. Dimensions of the puller 4
3. User manual 6
4. Jaws position 6
5. Spindle point 8
6. Exploded view 9

4
1. TECNHICAL FEATURES
• Two and three jaws pullers.
• Standard jaws (2 holes), long ones (3 holes) extra-long ones (4 holes).
• For exteriors.
• Forged jaws.
2. DIMENSIONS OF THE TWO JAWS PULLER
Item number with L long jaws with X Extra long jaws.
Reference A B C Ton. Weight
1300 60 60 37 0.5 0.2
1300L 70 67 37 0,5 0,2
1301 85 100 70 1 0,4
1301L 105 110 70 1 0,5
1304 135 150 76 4 1,2
1304L 185 175 76 4 1,4
1307 180 200 113 7 2,3
1307L 225 240 113,5 7 2,5
1308 180 250 160 7 2,7
1308L 225 290 160 7 2,9
1310 300 310 161 10 5,5
1310L 385 360 161 10 6
1310X 460 410 161 10 7,6
1317 370 425 280 17 11,5
1317L 480 480 280 17 13
1317X 600 540 280 17 15
1330 460 520 325 30 25,5
1330L 585 580 325 30 30
1330X 710 720 325 30 34,5
1350 750 850 402 50 49
1350L 900 980 402 50 55,5
1350X 1050 1080 402 50 62,3

5
2.1 DIMENSIONS OF THE THREE JAWS PULLER
The height in the chart is the maximum vertical position.
The opening is the maximum while opening at a 15 degrees angle.
Combina con
2/3 patas
Reference A B C TON Weight Combine
2/3
1300T 60 65 37 0.5 0.3 No
1300LT 70 77 47 0,5 0,3 No
1301T 85 105 70 1 0,7 Si
1301LT 105 115 70 1 0,7 Si
1304T 135 150 76 4 1,8 Si
1304LT 185 175 76 4 2,1 Si
1307T 180 200 108 7 3,3 Si
1307LT 225 240 108 7 3,5 Si
1308T 180 250 160 7 3,7 Si
1308LT 225 290 160 7 3,9 Si
1310T 300 310 161 10 7,5 Si
1310LT 385 360 161 10 8,5 Si
1310XT 460 410 161 10 10,9 Si
1317T 370 425 280 17 16,5 No
1317LT 480 480 280 17 18,5 No
1317XT 600 540 280 17 20,5 No
1330T 460 520 325 30 33,5 No
1330LT 585 580 325 30 39 No
1330XT 710 720 325 30 45,5 No
1350T 750 850 402 50 65 No
1350LT 900 980 402 50 75 No
1350XT 1050 1080 402 50 85,5 No

6
3. USER MANUAL
1. Make sure that the spindle is perfectly clean and greased.
2. Check that the shaft is punched otherwise use a point protector.
3. Make sure that jaws are evenly spread out from the spindle.
4. Apply the pulling force by turning the spindle. Never strike the spindle.
5. Never use the spindle while positionned exeedingly out of the body.
6. Make us of all necessary safety equipments.
4. ARM´S POSITION
It is advisable to place the jaws in the lowest possible hole. In this way, the jaws will be
less bended when applying great effort. (Figure 1)
As more height is needed the spindle starts to come out more (Figure 2). If the shaft
is bigger, the spindle will come out in excess of the body, (Figure 3), in that case when
pulling with the wrench we can twist the spindle.
When the height of the spindle is very high, it is better to change the position of the
legs. (Figure 4).
Figure 1 Figure 2

7
Figure 3 Figure 4
This series of puller can mount standard arms (05), long arms (06) or
extra-long (16).
The puller has more force when arms are set in the lowest holes.
In this position arm bend less when applying great force (Figure 1).
But if the spindle sticks out too much from the body it might bend when
using the wrench (Figure 4). This type of bending might lead to the
catching of the spindle.
Chose cautiously the position of the arms.

8
5. SPINDLE POINT
Fixed spindle point (1300 to 1307)
The spindles featuring a tempered point must be protected when the shaft is not punched.
Spindle with retractable point (1310 and beyond)
A Big size pullers come with a retractable point making the point protector uncessary.
Following are the instructions how to use the aforesaid point.
a) Case 1
If the spindle thrusts against a pointed shaft then the point slides in easily.
b) Case 2
Whenever the spindle pushes against a pointed shart the point slides in to ease the
pulling.
Fixed point for pointed shaft
Retractable point for at shaft
Muelle

9
6. EXPLODED VIEW
Spare part 2 short arms Spare part 3 extra-long arms
Spare parts 2 long arms
“T” bodies of big pullers can be acquired equipped with the bronze nut and the cover. The
references are: 131722, 133022 and 13522. (See comments from page 10).

10
Spindle
Bodies
Reference Screw L X H Point Puller
130003 M8 x 1 90 12 9 Fix 1300 / 1300T
130103 M10 x 1 124 14 12 Fix 1301 / 1301T / 1301L/1301LT
130403 M14 x 1,50 177 20 16 Fix 1304 / 1304T / 1304L/1304LT
130703 M18 x 1,50 235 24 19 Fix 1307 / 1307T /1307L/1307LT
131031 M20 x 1,50 321 25 22 Interchangeable 1310 / All models
131731 M27 x 2 377 30 27 Interchangeable 1317 / All models
133031 1 3/8" 12h. 510 38 35 Interchangeable 1330 / All models
135032 1 3/8" 12h. 535 38 35 Interchangeable 1350 / All models
The bodies of the pullers 13017T 1330 1330T
1350 1350 T They feature a bronze nut to
enhance the force. These nuts rest against a
toric gasket designed to absorbe hammering
impacts when pulling out the piece. The whole
is encased with 2 screws
11 Bronze nut
OR gasket
14 Cover
3 ars bodies
The bodies 1301T, 1304T , 1307T y 1310T are
2 and 3 arms.
Combina con
2/3 patas
*For 1317T, 1317LT and 3117XT pullers
acquired after 01/07/2018, bronze nut
reference is 131712.

11
Arms
Extra-long jaw 16
Long jawShort jaw
Ref arms P R E L D
130005 4,5 6,5 5 70 13
130006 4,5 6,5 5 85 13
130105 6,5 8 7 106 19
130106 7 7,5 8 127 19
130405 7 21 7 166 51
130406 8 21 7,5 219 51
130705 8,5 25 9 217 44,5
130706 8 25 10 264 44,5
131005 15 25 12,5 355 83
131006 15 25 12,5 436 83
131016 15 25 12,5 516 83
131705 15,5 32 16 435 115
131706 17,5 31 15,5 550 115
131716 17,5 31 15,5 665 115
133005 23 42 22 557 125
133006 24 41 22 698 125
133016 24 41 22 823 125
13505 27 50 30 850 150
135206 27 50 30 1060 150
135216 27 50 30 1210 150
If the body is assembled in the inverted
position, the M-5 screws will support all
the load and they will break.

S.L. de Herramientas Especiales Forza
C/ San Miguel de Atxa, 24
01010 Vitoria
www.forza.es