Four-Faith F-NR130 User manual

5G Industrial Router
F-NR130
User Manual
V2.0.0
This manual is applicable to the following products: F-NR130
Xiamen Four-Faith Communication Technology Co., Ltd.
https://www.fourfaith.com

F-NR130 User Manual
Document Revision History
Date
Version
Note
Author
2022.5.17
V2.0.0
First Version
Jonas

F-NR130 User Manual
Note: There may be differences between models of accessories and interfaces, actual products shall
prevail.

F-NR130 User Manual
Copyright Notice
All contents in the files are protected by copyright law, and all copyrights are reserved by Xiamen Four-Faith
Communication Technology Co., Ltd.
Without written permission, all commercial use of the files from Four-Faith are forbidden, such as copy,
distribute, reproduce the files, etc., but non-commercial purpose, downloaded or printed by individual (all files
shall be not revised, and the copyright and other proprietorship notice shall be reserved) are welcome.
Trademark Notice
Four-Faith, 四信, , , are all registered trademarks of Xiamen Four-Faith
Communication Technology Co., Ltd., illegal use of the name of Four-Faith, trademarks and other marks of
Four-Faith is forbidden, unless written permission is authorized in advance.
Contact Us
Address:
11th Floor, A-06 Area, No.370, Chengyi Street, Jimei District, Xiamen City, Fujian Province, China
Website:
www.fourfaith.com
Tel:
[phone] 5907277
Fax:
[phone]
Post Code:
361021
E-mail:
[email protected]

F-NR130 User Manual
Content
Chapter 1 Product Introduction ........................................................................................1
1.1 Product Overview ...................................................................................... 1
1.2 Diagram of Working Principle ......................................................................... 2
Chapter 2 Installation .......................................................................................................3
2.1 Overview.........................................................................................................................................3
2.2 Packing List....................................................................................................................................3
2.3 Installation and Cable Connection.................................................................................................4
2.4 Power Supply.................................................................................................................................6
2.5 Indicators........................................................................................................................................7
2.6 Reset Button...................................................................................................................................7
Chapter 3 Configuration and Management .......................................................................8
3.1 Configuration Connection...........................................................................................................8
3.2 Access the Configuration on Web Page.....................................................................................9
3.3 Management and Configuration...............................................................................................11
3.3.1 Setting ............................................................................................................................11
Basic Setting.............................................................................................................11
Dynamic DNS ...........................................................................................................17
Clone MAC Address .................................................................................................18
Advanced Router......................................................................................................18
VLANS ......................................................................................................................19
Networking................................................................................................................20
3.3.2 Wireless..........................................................................................................................23
Basic Setting.............................................................................................................23
Wireless Security......................................................................................................25
3.3.3 Services..........................................................................................................................27
Services ...................................................................................................................27
3.3.4 VPN................................................................................................................................30
PPTP.........................................................................................................................30
L2TP..........................................................................................................................31
OPEN VPN ...............................................................................................................33
IPSEC .......................................................................................................................37

F-NR130 User Manual
GRE ......................................................................................39
3.3.5 Security.......................................................................................41
Firewall ...................................................................................41
3.3.6 Access Restrictions .........................................................................44
WAN Access.............................................................................44
URL Filter ................................................................................47
Packet Filter..............................................................................47
3.3.7 NAT...........................................................................................49
Port Forwarding..........................................................................49
Port Range Forward.....................................................................50
DMZ ......................................................................................50
3.3.8 QoS Setting..................................................................................51
Basic......................................................................................51
Classify...................................................................................52
3.3.9 Applications..................................................................................52
Serial Applications.......................................................................52
3.3.10 Administration ..............................................................................54
Management.............................................................................54
Keep Alive................................................................................56
Commands...............................................................................57
Factory Defaults .........................................................................58
Firmware Upgrade.......................................................................58
Backup ...................................................................................59
3.3.11 Status .......................................................................................60
Router ....................................................................................59
WAN......................................................................................62
LAN.......................................................................................64
Wireless ..................................................................................66
Bandwidth................................................................................68
Sys-Info...................................................................................69
Appendix ................................................................................................................ 72

www.fourfaith.com 1Copyright @ Four-Faith 2021
F-NR130 User Manual
Chapter 1 Product Introduction
1.1 Product Overview
F-NR130 is a wireless communication router for the Internet of Things, which uses
public 3G/4G/5G networks to provide users with wireless long-distance big data
transmission functions.
The product adopts high-performance industrial-grade 32-bit communicationprocessor
andindustrial-gradewirelessmodule,withembedded real-time operating system as the
software support platform, and provides 1xRS232, 1xRS485, 1xEthernet LAN and 1
Ethernet WAN/LAN(Default for the LAN), which can connect serial devices, Ethernet
devices and WIFI devices at the same time to realize data transparent transmission and
routingfunctions.
This product has been widely used in the M2M industry on the Internet of Things industry
chain, such as smart grid, smart transportation, smart home, finance,mobilePOS
terminals,supplychainautomation,industrialautomation, smart buildings, fire protection,
public safety, environmental protection, meteorology,Digitalmedicaltreatment,remote
sensingsurvey,military,space exploration, agriculture, forestry, water affairs, coal mine,
petrochemical and other fields.

www.fourfaith.com 2Copyright @ Four-Faith 2021
F-NR130 User Manual
1.2 Block Diagram of Working Principle
(Linux)
1 SIM 2 Module
Ethernet
Power Supply

www.fourfaith.com 3Copyright @ Four-Faith 2021
F-NR130 User Manual
Chapter 2 Installation
2.1 Overview
5Groutersmustbeinstalledcorrectlytoachievethedesignedfunctions.Usually, the
installation of the equipment must be carried out under the guidance of qualified
engineers approved by the company.
2.2 Packing List
When youopen the box, please keep the packing materials, so that you can use it when
you need to transfer in the future.
The list is as follows:
· 1 x 5G router
· 4 x 5G wireless cellular antennas (SMA male)
· 1 x WIFI antenna (SMA female)
· 1 x Matching power supply
· 1 x Ethernet cable
· 1 x Warranty card
· 1 x terminal block

www.fourfaith.com 4Copyright @ Four-Faith 2021
F-NR130 User Manual
2.3 Installation and Cable Connection
Dimension (mm):
Antenna Installation:
The 5G antenna interface is an SMA female socket. Screw the SMA maleof the matching
wireless cellular antenna to the antenna interface and make sure totightenit. To increase
theisolationofthe5Gantenna,try to keepthe antenna at an angle of 30 degrees to
enhance signal quality.
The WIFI antenna interface is an SMA male socket. Screw the SMA female of the matching
WIFI antenna to the antenna interface and make sure to tighten it. In addition, to increase the
isolation of the Wi-Fi antenna, it is recommended that the two Wi-Fi are placed at a 90-
degree angle.

www.fourfaith.com 5Copyright @ Four-Faith 2021
F-NR130 User Manual
SIM/UIM installation：
When installing or removing the SIM/UIM card, first use a pointed object to gently hold the
eject button, and the SIM/UIM card sleeve will pop out. Ensure that the metal contact
surface of the SIM/UIM card is facing correctly. Above is the position of SIM1: the missing
angle is inward, and the contact surface of the SIM/UIM card is downward. Below is the
position of SIM2: missing angle is inward, metal contact surface of the SIM/UIM card is
downward
Ethernet Cable:
Insert the network connection cable at one end of the straight to 5G router LAN/WAN or LAN, and on
the other end into the Ethernet interface on the user's device. The direct network signal connection is
as follows:
RJ45-1
RJ45-2
Color
1
1
White/Orang
e
2
2
Orange
3
3
White/Green
4
4
Blue
5
5
White/Blue
6
6
Green
7
7
White/Brown
8
8
Brown

www.fourfaith.com 6Copyright @ Four-Faith 2021
F-NR130 User Manual
3.5 mm Terminal Interface Definition:
Using 5 pin terminal 3.5 mm of the interface, POWER, and function of RS232 and RS485. Specific
definitions are as follows:
5 PIN 3.5 mm Terminal Interface Signal Definition
Number
Definition
Signal Description
Extended Function
1
VCC
Positive of devices
power supply terminal
2
GND
Negative of devices
power supply terminal
RS232 common ground
3
TXD
RS232 transmitting end
4
RXD
RS232 receiving end
5
B
RS485 B end
6
A
RS485 A end
Serial Port:
To use a serial port connection, the stripping end of the terminal serial port to receive the 3.5 mm
terminal of the Router interface (GND TX RX), the DB9 end plug on the RS232 serial interface to the
user equipment, terminal serial port signal connection is as follows:
Definition of Terminal Serial Cable Signal (RS232)
Number
Color
Signal Definition
DB9F
Signal
Description
Description
1
Brown
TXD
2
Send data
Output
2
Blue
RXD
3
Receive data
Input
3
Black
GND
5
Ground
2.4 Power Supply
5G routers are usually used in complex external environments. To adapt to the complex
application environment and improve the stability of the system, the router adopts
advanced power supply technology. Users can use the standard 12VDC/1.5Apower
adapter topower the 5G router,or directly use the DC 9~36V power supply to power the
router. When the user uses an external power supply to power the router, the stability of
the power supply must be ensured (the ripple is less than 300mV,and the instantaneous
voltage does not exceed 36V), and the power supply must be greater than 8W.

www.fourfaith.com 7Copyright @ Four-Faith 2021
F-NR130 User Manual
2.5 Indicators
5GRouterprovideindicatorsasbelow：“PWR”,“SyS”,“Online”, “WiFi”：
Indicator
Status
Content
PWR
On
Device powered on
SYS
Blank
System running normally
Off
System not running
WiFi
On
WiFi turn on
On
WiFi turn off
Online
Blank
Connect with 4G network
On
Connect with 5G network
Off
Device offline
2.6 Reset Button
The 5G router has a reset button, marked as "RST"
The function of this button is to restore the parameter configuration of the 5G router to
factory values
Methodsasbelow:Poweron device, let itrunning for30 seconds,usea pen keep pressing
the reset button for about 15 seconds, until all led turn off, the device will restart and reset
to factory.

www.fourfaith.com 8Copyright @ Four-Faith 2021
F-NR130 User Manual
Chapter 3 Configuration and Management
This chapter describes how to configure and manage the Router.
3.1 Configuration Connection
Before configuring a 5G router, connect the 5G router to the PC using a factory
configured network cable or WiFi. When using a network cable, one end of the network
cable is connected to any Ethernet port of a 5G router, LAN/WAN, or LAN, and the other
end is connected to the Ethernet port of a PC. When WIFI is used, the default SSID of 5G
industrial routers is "FOUR-FAITH", which does not require password verification. Please
modifytheIP addressofPCasthesame network segment address of the Router, for
instance, 192.168.1.9. Modify the mask code of PC as 255.255.255.0 and set the default
gateway of PC as the Router’s IP address (192.168.1.1).
Network Cable Power Supply

www.fourfaith.com 9Copyright @ Four-Faith 2021
F-NR130 User Manual
3.2 Access the Configuration Web Page
The chapter is to present main functions of each page. Users visit page tool via web
browser after connecting users' PC to the Router. There are eleven main pages: Setting,
Wireless, Service, VPN, Security,Access Restrictions, NAT,QoS Setting, Applications,
Management and Status. Users enable to browse slave pages by click one main page.
3.2.1 IP configurations in PC
The first method: Obtain an IP address automatically:
The second way: specify the IP address
Set the IP address of the PC to 192.168.1.9 (or other IP addresses in the 192.168.1 network
segment), the subnet mask is set to: 255.255.255.0, and the default gateway is set to: 192.168.1.1.
DNS is set to gateway address or local available DNS server.

www.fourfaith.com 10 Copyright @ Four-Faith 2021
F-NR130 User Manual
3.2.2 Log in to the configuration page
To access the web-based web management tool of the 5G industrial router, start IE or other browsers,
and enter the default IP address 192.168.1.1 of the 5G industrial router in the "Address" field. Press the
Enter key.
If you log in to the Web page for the first time, you can see the page shown below, prompting the user
whether to modify the default username and password of the 5G industrial router. If you need to enter
the user-defined username and password, click the "Change Password" button to apply.
If you click the main menu for the first time, you need to enter the corresponding username and
password.

www.fourfaith.com 11 Copyright @ Four-Faith 2021
F-NR130 User Manual
If you click the main menu for the first time, you need to enter the corresponding username and
password
Enter the correct user and password to access the corresponding menu page. The default username is
admin and the default password is admin.
3.3 Management and Configuration
3.3.1 Setting
The Setup screen is the first screen users will see when accessing the Router. Most users
will be able to configure the Router and get it work properly using only the settings on this
screen. Some Internet Service Providers (ISPs) will require users to enter specific
information, such as Username, Password, IP Address, Default Gateway Address, or
DNS IP Address. This information can be obtained from your ISP, if required.
Basic Setting
WAN Connection Type
Seven Ways: Disabled, Static IP, Automatic Configuration-DHCP, PPPOE,
3G/UNMTS/4G/LTE, DHCP-4G/5G.
1. Disabled
Forbid the setting of WAN port connection type

www.fourfaith.com 12 Copyright @ Four-Faith 2021
F-NR130 User Manual
2. Static IP
WAN IP Address: Users set IP address by their own or ISP assigns
Subnet Mask: Users set subnet mask by their own or ISP assigns
Gateway: Users set gateway by their own or ISP assigns
Static DNS1/DNS2/DNS3: Users set static DNS by their own or ISP assigns
3. Automatic Configuration-DHCP
IP address of WAN port gets automatic via DHCP
4. PPPOE
Username: login the Internet
Password: login the Internet
5. 3G/UMTS/4G/LTE

www.fourfaith.com 13 Copyright @ Four-Faith 2021
F-NR130 User Manual
Username: Login users' ISP (Internet Service Provider)
Password: Login users' ISP
Dial String: Dial number of users' ISP
APN: Access point name of users' ISP
PIN: PIN code of users' SIM card
6. Connection Type
Connection type: Auto, Force 3G, Force 2G, prefer 3G, Prefer 2G options. If using 4G
module, there has 4G network option. Users select different mode depending on
their need
7. DHCP-4G
IP address of WAN port gets automatic via DHCP-4G
8. DHCP-4G/5G
The IP address of the WAN port is obtained in DHCP-4G/5G mode. The default Auto network type
selection, namely, at the same time support the NSA and SA. This option is best set to separate SA
or separate NSA according to the actual network environment.
9. Keep Online
Thisfunctionisusedtodetectwhetherthe Internetconnectionisactive,ifusers set it and
when the Router detect the connection is inactive, it will redial to users' ISP immediately to
make the connection active. If the network is busy or the user is in private network, we
recommend that Router mode will bebetter.
10. Detection Method
None: Do not set this function
Ping: Send ping packet to detect the connection, when choose this method, users should
also configure "Detection Interval", "Primary Detection Server IP" and "Backup Detection
Server IP" items.
Route: Detect connection with route method, when choose this method, users should
also configure "Detection Interval", "Primary Detection Server IP" and "Backup Detection
Server IP" items.
PPP: Detect connection with PPP method, when choose this method, users should also

www.fourfaith.com 14 Copyright @ Four-Faith 2021
F-NR130 User Manual
configure "Detection Interval" item.
Detection Interval: Time interval between two detections, unit is second
Primary Detection Server IP: The server used to response the Router’s detection
packet. This item is only valid for method "Ping" and "Route".
Backup Detection Server IP: The server used to response the Router’s detection packet.
This item is valid for method "Ping" and "Route".
Note: When users choose the “Route” or “Ping” method, it’s quite important to make sure
that the “Primary Detection Server IP” and “Backup Detection Server IP” are usable and
stable, because they have to responsethe detection packet frequently.
Force Reconnect: ThisoptionschedulesthePPPOE or3G reconnectionbykilling the
PPPD daemon and restart it.
Time: Needed time to reconnect
11. STP
STP (Spanning Tree Protocol) can be applied to loop network. Through certain algorithm
achieves path redundancy, and loop network cuts to tree-based networkwithoutloopin
themeantime,thus,toavoidthehyperplasiaandinfinite circulation of a message in the
loop network
12. Optional Configuration
Router Name: Set Router name
Host Name: ISP provides
Domain Name: ISP provides
MTU: Auto (1500) and manual (1200-1492 in PPPOE/PPTP/L2TP mode, 576-16320 in
other modes)