Four Seasons Courtyard SRGF11626 User manual

Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-866-814-0585, 8 a.m. - 8 p.m., EST, Monday - Friday.
E-mail: [email protected]
30'' 50,000 BTU
GAS FIRE PIT
Model #: SRGF11626
Item #: 227770

If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department.
DANGER WARNING: For Outdoor Use
Only.
CAUTION:
Installer: Leave the instruction manual
to the user for future use.
Consumer: Please keep this manual
for future reference.
Do not store or use gasoline or
other flammable vapors and liquids
in the vicinity of this or any other
appliance.
WARNING
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
WARNINGS AND CAUTIONS
Read the instructions before use. This appliance must be installed in accordance with such
regulations as are enforced.
•Do not try to light the appliance.
•Do not touch any electrical switch; do not use any phone in the vicinity of this product.
•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.
•If you cannot reach your gas supplier, call the fire department.
WARNING:
CARBON MONOXIDE HAZARD
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Read the installation, operation and
maintenance instructions thoroughly before installing or servicing this
equipment.
WHAT TO DO IF YOU SMELL GAS?
Installation and service must be performed by a qualified installer, service agency or gas
supplier.
!
This appliance can produce carbon monoxide which
has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such
as a camper, tent, car or home.
2

TABLE OF CONTENTS
Warnings and Cautions...................................................................2, 4-5
Table of Contents...................................................................................3
Tools and Parts...................................................................................6-7
Assembly Instructions.......................................................................8-16
Installation Instructions ........................................................................17
Operation.........................................................................................18-20
Locating Fire Pit For Use......................................................................21
Maintenance and Storage...............................................................22-23
Trouble Shooting..................................................................................24
Warranty Information............................................................................25
REMINDER
BEFORE ASSEMBLY
Verify that all parts are included with your gas fire pit BEFORE you begin assembly by checking the Parts and
Hardware List. For your convenience, some parts may be pre-assembled or attached to fire pit components.
If all parts are not included, do not attempt to assemble fire pit. Call the toll free number on the cover
page for replacement parts.
Leave hardware installed HALF-TIGHTENED on the gas fire pit during assembly until unit is completely
assembled, then finish tightening all hardware installed.
YOUR OWNER’S MANUAL
Keep and store this Owner’s Manual for future reference – it contains important instructions and
procedures for safety and maintenance.
3

WARNINGS AND CAUTIONS
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES
WARNING:
!
The installation must comform with local codes or, in the absence of local codes, with the
CAN/CGA-B 149.2, Propane Installation Code.
This appliance requires 20 lb (9 kg) LP gas supply cylinder.
The burner must be replaced prior to the appliance being put into operation if it is evident that the
burner is damaged. The replacement burner shall be that specified by the manufacturer.
Installation and repair should be done by a qualified service person. The appliance should
be inspected before use and at least annually by a qualified service person. More frequent
cleaning may be required as necessary. It is imperative that control compartment, burners,
and circulating air passageways of the appliance be kept clean.
Always place the appliance on a firm and level surface.
Do not burn solid fuels in this gas appliance.
Use the appliance outdoors in a well-ventilated space only, not in a building, garage, or any other
enclosed area.
When using the appliance, keep the appliance area clear and at least 50 inches from combustible
materials, gasoline and other flammable liquid and vapors. Certain items or materials, when stored
under the appliance or nearby, will be subjected to radiant heat and could be seriously damaged.
Inspect the gas connections of appliance prior to each use. Do not operate the unit if there is gas
leak. A qualified service person should inspect the appliance annually.
Alert children and adults to the hazards of high surface temperatures and keep them away
to avoid burns or clothing ignition.
Carefully supervise children and pets when they are near the appliance.
Replace guard or other protective device removed for servicing.
Do not hang clothing or other flammable materials on or near the appliance.
Do not use the appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control which has been under water.
The LP-gas supply cylinder to be used must be: Constructed and marked in accordance with the
Specifications for LP-gas cylinders of the U.S. Department of Transportation (DOT); or the
Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and
Commission, CAN/CSA-B339, as applicable.
The LP-gas supply cylinder to be used must be provided with a listed overfilling prevention device;
and provided with a cylinder connection device compatible with the connection for the appliance.
Use only a cylinder supply system arranged for vapor withdrawal, and the cylinder must include a
collar to protect the cylinder valve.
4

This appliance is designed to operate with a standard 20 Ib propane cylinder with Approved
Cylinder Connection.
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES:
Before beginning assembly of product, make sure all parts are present. If any part is missing or
damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
Perform a leak test with a soapy solution:
1. To check gas connections.
2. After connecting a new cylinder.
3. Upon re-assembly after disassembly.
WARNINGS AND CAUTIONS
WARNING:
This product can expose you to chemicals including lead, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to the State of California to
cause birth defects or other reproductive harm. For more information, go to:
www.P65Warnings.ca.gov.

SPECIFICATION
Certification CSA
Rated Heat Input 50000 BTU/HR
Fuel LP
Gas Supply 20 lb (9 kg) LP gas cylinder
Manifold Pressure 11” W.C.
Injector Size(diameter) 2.22mm
Gas Supply Pressure
Max. 250PSI, Min. 5PSI
5

TOOLS NEEDED: (NOT INCLUDED)
Philips screwdriver
Estimated time for assembly: 30-45 minutes.
PACKAGE CONTENTS
6
M
Q
P
B
D
A
F
E
C
H
G
N
O
LK
I
J

Back Right Leg
Cylinder Locking Bolt
Cylinder Holder
Door Handle
Cylinder Holder Pole
Side Panel
PART DESCRIPTION QUANTITY PART DESCRIPTION QUANTITY
1A
3B 1C
1D
E
F
G
L
J
1
2
1
1
1
1
Cover Lid
Lava Rock
M
N
K
1
1
PACKAGE CONTENTS
Control Panel Assembly
Back Left Leg
Table Top Frame
Front Left Leg
HARDWARE CONTENTS (shown actual size)
M5 x 12 Bolt Assembly M5 x 12 Bolt M5 x 20 Bolt M6 x 12 Bolt ST4.2 x 9.5 Bolt
Qty. 4 Qty. 20 Qty. 4 Qty. 16 Qty. 4
AA CC DD EE
BB
1
7
Front Right Leg
Door
1
1
H
O
P
Q
Protect Bar
Cus ion Pad
Ceramic Tile
1
4
I
16

Assembly Instructions
Choose a good, cleared assembly area and get a friend to help you put your gas fire pit together.
Lay cardboard down to protect gas fire pit finish and assembly area.
Step 1 Fig. 1
Place the Table Top Frame (A) upside
down to the soft, level surface, attach
control panel assembly (C) to the Table
Top Frame (A) with (4) M5x12 bolts
assembly (AA) as Fig. 1.
Insert valve into the injection pipe of
burner as illustrated (Position A).
Insert the end of electrode wire into
valve as illustrated (Position B).
Adjust the distance between the ignition
pin and flame orifice to be 4-5mm in
case of ignition failure (If ignition failure
issue happened).
4-5mm
4-5mm
Note: With the help of a friend, turn the
table top upside down to begin assembly.
Hardware Used
AA M5 x 12 Bolt Assembly
A
C
x 4
AA
AA
Position B
Position A
Injection Pipe
Electrode WireValve
ignition pin
flame orifice
8

Assembly Instructions
Step 2
Step 3
Fig. 2
Fig. 3
Attach front left leg (E), back left leg (D),
front right leg (H) and back right leg (G)
to the Table Top Frame (A) with (12)
M6x12 bolts (DD) as Fig.2.
D
G
A
H
BD
E
A
BB
BB
E
DD
Attach side panel 1 (B) to front left leg (E)
and back left leg (D) with (6) M5x12 bolts
(BB) as Fig.3.
Hardware Used
BB M5 x 12 Bolt x 6
Hardware Used
DD M6 x 12 Bolt x 12
9

Assembly Instructions
Step 5
Fig. 4
Fig. 5
Step 4
Attach cylinder holder pole (F) to back
left leg (D) and front left leg (E) with
(2) M5x20 bolts (CC) as
Note: The side with arrow sticker assemble
to front left leg (E).
Fig. 4.
Hardware Used
CC M5 x 20 Bolt x 2
CC
A
BB
BB
G
B
E
D
D
F
Attach side panel 2 (B) to back left leg (D)
and back right leg (G) with (6) M5x12
bolts (BB) as Fig.5.
Hardware Used
BB M5 x 12 Bolt x 6
10

Assembly Instructions
Step 6
Step 7
Fig. 6
Fig. 7
Attach side panel 3 (B) to front right leg
(H) and back right leg (G) with (6) M5x12
bolts (BB) as Fig.6.
Hardware Used
BB M5 x 12 Bolt x 6
G
B
H
H
G
F
BB
BB
CC
Attach another cylinder holder pole (F)
to front right leg (H) and back right
leg (G) with (2) M5x20 bolts (CC)
as
Note: the side with arrow sticker assemble
to front right leg (H).
Fig. 7.
Hardware Used
CC M5 x 20 Bolt x 2
11

Assembly Instructions
Step 8
Step 9
Fig. 8
Fig. 9
Screw door handle (J) to door (I) as Fig. 8. I
J
KL
Screw cylinder locking bolt (L) to cylinder
holder (K) as Fig. 9.
12

Assembly Instructions
Step 10 Fig. 10
Attach cylinder holder (K) to cylinder hold
poles (F) with (4) M6x12 bolts (DD) as
Fig. 10.
F
F
F
K
K
K
DD
DD
DD
Hardware Used
DD M6 x 12 Bolt x 4
13

Assembly Instructions
Fig. 11 BB
OA
Hardware Used
BB M5 x 12 Bolt x 2 C
Step 12 Fig. 12
Attach door (I) to front right leg (H)
assembly with (4) ST4.2x9.5 bolts (EE)
Note: With the help of a friend, turn the
gas fire pit into upright position after this
step finished.
as Fig. 12.
H
I
Hardware Used
EE ST4.2 x 9.5 Bolt x 4
EE
EE
14
Step 11
Attach the protect bar (O) to the bottom
of fire bowl with (2) M5x12 bolts (BB) as
Fig. 11.

Assembly Instructions
Step 13 Fig. 13
P
A
A
Q
15
Fig. 14
Peel and stick the cushion pads (P) on
the table top frame (A) as Fig.13, total
16 cushion pads.
Note: Before applying the adhesive
cushion pads, be sure to wipe down the
metal surface and make sure it is free of
any dust or debris.
Step 14
Put (4) ceramic tiles (Q) on table
top frame (A) as Fig.14.
P

Assembly Instructions
Step 15 Fig. 15
Put the lava rocks (N) into the
burning area ,middle of tabletop.
Place the cover lid (M) onto the table
top when the gas fire pit not use.
Note: To avoid ignition failure, do not
cover the flame orifice with lava rocks.
M
tabletop
Flame Orifice
N
16

16
17
I
lava rocks (max 8.8 lb)
Open the door (I)
(Fig. 16)
4. Turn the cylinder locking bolt clockwise to secure the gas
cylinder. (Fig. 17)
18
19
6
INSTALLATION INSTRUCTIONS
Your gas fire pit has been checked at all connections at the
factory for leakage.
In transportation and handling some connections may have
loosened. Follow these steps to check the hose/
regulator/cylinder connections:
1) Make leakage solution by mixing 1part liquid dish soap and 3
parts water.
2) Spoon or brush several drops (or use squirt bottle) of the
solution onto hose/regulator/cylinder connection.
3) Turn on gas cylinder. Inspect the connections and look for
bubbles.
4) If no bubbles appear, the connection is safe.
5) If bubbles appear, there is leakage. Loosen and re-tighten this
connection. If there is still a leak, please call customer service:
1-866-814-0585.
Note:
1) The cylinder supply system must be arranged for vapor
withdrawal.
2) The cylinder used must include a collar to protect the cylinder
valve.
The hose assembly must be replaced prior to the appliance being
put into operation if there is evidence of excessive abrasion or
wear, or if the hose is damaged.
At least once a year, a complete inspection of the entire gas path
components should be performed.
If there is need to replace parts, proceed to leak test after
reassembly (These procedures should be performed by a profes-
sional technician).
18
19 P2
P1
Tighten
regulator & cylinder
connection
17

WARNING: DO NOT ATTEMPT TO OPERATE THE APPLIANCE UNTIL YOU HAVE READ AND
UNDERSTAND ALL PRECAUTIONS. FAILURE TO DO SO CAN RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY, OR DEATH.
WARNING
WARNING
WARNING
FOR YOUR SAFETY:
DO NOT touch or move gas appliance
for at least 45 minutes after use.
Lighting operations should comply
with Lighting Instruction section.
Improper lighting operations will
cause serious injury and explosion.
Before turning gas supply ON
Your fire pit was designed and approved for OUTDOOR
USE ONLY. DO NOT use it inside a building or any other
enclosed area.
Make sure surrounding areas are free of combustible
materials, gasoline, and other flammable vapors or liquids.
Ensure that there is no obstruction to air ventilation.
Be sure all gas connections are tight and there are no leaks.
Be sure the access panel is clear of debris.
Be sure any component removed during assembly or
servicing is replaced and fastened prior to starting.
FOR YOUR SAFETY:
WARNING!!!
Do not use an open flame to check for leakage.
Do not smoke during testing.
Do not test indoors.
A leak check must be performed whenever the gas
cylinder is replaced.
NOTE:
U se only the pressure regulator supplied with this fire pit.
Replace them with those specified by the manufacturer
only.
OPERATION
If at any time you are unable to
light burner and smell gas, wait 5
minutes to allow gas to dissipate
before attempting to light gas
appliance. If after 1 minute, you
are unable to light burner, wait 5
minutes and allow flammable
vapors to dissipate before
attempting to light gas appliance.
18

ATION
Before Lighting
The gas fire pit should be thoroughly inspected before each
use, and by a qualified service person at least annually.
If relighting a hot gas fire pit, always wait at least 5 minutes.
Lighting Instructions
1. Make sure control knob is in the “OFF” position.
2. Turn LP cylinder gas valve to fully open position.
3. Press down control knob and turn it counter clockwise
to "LOW" position, this will light the burner. (You will hear 1
clicking noise.)
4. If the burner is not lit immediately (within 5 seconds), press
down the control knob and turn clockwise to "OFF" position,
repeat from step 3 after 5 minutes.
5. When burner is lit, turn the control knob to desired heat output position between "LOW"
and "HIGH".
Flame Characteristic
Normally the burner flame is yellow.
If the burner flame is blue and very small, please check the
gas cylinder, as it may be low gas pressure or empty. If there
is enough gas in the cylinder, please contact customer service
to change the burner of the gas fire pit.
If flames lift away from burner or backfire happens, or produce
thick black smoke, the fire pit should be turned off immediately.
The fire pit should not be operated again until the unit is serviced
and/or repaired by a qualified service technician.
WARNING: DO NOT ATTEMPT TO OPERATE THE APPLIANCE UNTIL YOU HAVE READ AND
UNDERSTAND ALL PRECAUTIONS. FAILURE TO DO SO CAN RESULT IN PROPERTY
DAMAGE, SERIOUS INJURY, OR DEATH.
OPERATION
19

CAUTION: AVOID INHALING FUMES EMITTED FROM THE GAS APPLIANCE'S FIRST USE.
SMOKE AND ODOR FROM THE BURNING OF OILS USED IN MANUFACTURING WILL
APPEAR. BOTH SMOKE AND ODOR WILL DISSIPATE AFTER APPROXIMATELY 30
MINUTES. THE GAS APPLIANCE SHOULD NOT PRODUCE THICK BLACK SMOKE.
NOTE:
The burner may be noisy when initially turned on. To eliminate
excessive noise from the burner, turn the control knob to the
“LOW” position. Then, turn the knob to the level of heat desired.
Operation pressure checked:
If the flame is very small, this is because the supply
pressure is not enough. Please refill gas cylinder.
Re-light:
1) Turn the control knob to "OFF"position.
2)
3) Repeat steps beginning with step 3 of the lighting
instruction.
Shut down instructions:
1) Push in and turn control knob clockwise to "OFF"
position.
2)
2) Turn LP cylinder valve to "OFF" position.
The Event of Gas Leakage:
1) Turn the control knob to "OFF" position.
3) Wait 5 minutes to allow gas to dissipate.
4) If odor continues, immediately call gas supplier.
WARNING : Gas appliance will be hot after use.
Handle with extreme care.
Wait five (5) minutes before attempting to relight appliance.
Turn LP cylinder gas valve clockwise to "OFF" position
when appliance is not in use.
OPERATION
20