FPI E33-LP Quick start guide

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
918-408
WARNING:
Improper installation, adjustment, alteration, service or main-
tenance can cause injury, property damage, or loss of life.
Refer to this manual. For assistance or additional informa-
tion consult an authorized installer, service agency or the
gas supplier.
FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapours and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by an authorized
installer, service agency or the gas supplier.
FOR YOUR SAFETY:
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your build-
ing.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas sup-
plier, call the fire department.
08/16/05
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
E33 Gas Insert
Owners & Installation Manual
MODELS: E33-NG Natural Gas E33-LP Propane

2E33 FPI Direct Vent Gas Insert
FPI GAS FIREPLACE INSERT
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by FPI.
The E33 Gas Insert has been designed to provide you with all the warmth and charm of a fireplace,
at the flick of a switch. The E33-NG and E33-LP have been approved by Warnock Hersey for
both safety and efficiency. As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow. Please take a moment now to acquaint
yourself with these instructions and the many features of your FPI Fireplace.
16-1/2"(419mm)
23-13/16"(605mm)
1-3/8"
(35mm)
24-1/2"(622mm)
32-1/4"(819mm)
25"(635mm)
16-1/8"(410mm)
45-9/16"(1157mm)
31-1/8"(790mm)
18"(203mm)
11-1/4"
(286mm)
23"(583mm)

3
E33 FPI Direct Vent Gas Insert
TABLE OF CONTENTS
FPI GAS FIREPLACE INSERT
OPERATING INSTRUCTIONS
First Fire ........................................................................ 18
Operating Instructions .......................................................... 18
Lighting Procedure ............................................................... 18
Shutdown Procedure ............................................................ 18
Copy of Lighting Instruction Plate......................................... 19
Automatic Convection Fan Operation .................................. 19
Normal Operating Sounds of Gas Appliances...................... 19
MAINTENANCE
Maintenance Instructions ..................................................... 20
General Vent Maintenance .................................................. 20
Log Replacement ................................................................. 20
Glass Gasket ....................................................................... 20
Steel or Gold Plated Trim ..................................................... 20
Door Glass ........................................................................ 21
Flush Glass Replacement .................................................... 21
Fan Maintenance.................................................................. 21
Valve Assembly Removal and Installation ........................... 22
REPLACEMENT PARTS LIST
Parts List ........................................................................ 23
WARRANTY
Warranty ........................................................................ 31
Page
Unit Dimensions ..................................................................... 2
Safety Label .......................................................................... 4
INSTALLATION REQUIREMENTS
For Your Safety....................................................................... 5
Gas Pressure Testing ............................................................. 5
Specifications ......................................................................... 5
Installation into a Solid Fuel Burning
Fireplace or Factory Built Fireplace ................................ 5
General Safety Information .................................................... 5
Installation Checklist............................................................... 6
Materials Required ................................................................ 6
Minimum Fireplace Dimensions ............................................. 6
Clearances to Combustibles .................................................. 7
Combustible Mantel Clearances ............................................ 7
INSTALLATION
Gas Connection...................................................................... 8
Venting .......................................................................... 8
Flue Liner Installation ............................................................. 8
Gas Pipe Pressure Test.......................................................... 9
SIT Valve Description ............................................................ 9
Gas Insert Aeration System.................................................... 9
Optional Brick Panel .............................................................. 9
Log Installation .................................................................... 10
E33 Conversion Kit from NG to LPG.................................... 12
Faceplate & Trim .................................................................. 13
Standard Flush Door ............................................................ 14
Flush Louvers ....................................................................... 14
Full Screen Front.................................................................. 14
Excalibur Surround Installation............................................. 15
Optional Screen Doors ......................................................... 16
Accent Kit Installation ........................................................... 16
Double Door Option.............................................................. 16
Wiring Diagram..................................................................... 17
Optional Remote Control ..................................................... 17
Optional Wall Thermostat ..................................................... 17
Final Check ........................................................................ 18
Page

4E33 FPI Direct Vent Gas Insert
SAFETY LABEL
This is a copy of the labels that accompany each
E33 Gas Insert. We have printed a copy of the
contents here for your review. The safety label
is located on a plate inside the base of the unit
visible when the bottom louver is opened. Ensure
that the safety label is attached to the unit.
NOTE: FPI units are constantly being im-
proved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.

5
E33 FPI Direct Vent Gas Insert
IMPORTANT:
SAVE THESE
INSTRUCTIONS
The FPI Gas Fireplace must be installed in
accordance with these instructions. Carefully
read all the instructions in this manual first.
Consult the building authority having jurisdic-
tion to determine the need for a permit prior to
starting the installation.
NOTE: Failure to follow the instructions could
cause a malfunction of the heater which could
result in death, serious bodily injury, and/or
property damage. Failure to follow these
instructions may also void your fire insurance
and/or warranty.
FOR YOUR SAFETY
This appliance requires air for proper combus-
tion. Always provide adequate combustion and
ventilation air. Follow instructions and informa-
tion in CSA B149.1 (in Canada) or the National
Fuel Gas CodeANS Z223.1/NFPA (in the USA),
regarding requirements for combustion and
ventilation air.
GAS PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut off valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than
1/2 psig. (3.45 kPa).
SPECIFICATIONS
At pressures over 1/2 psig, the pipe to the unit
must be disconnected.
Gas Input Capacity:
Natural Gas 38,000 Btu/h
Propane 35,500 Btu/h
Min. Input:
Natural Gas 20,000 Btu/h
Propane 19,000 Btu/h
Fuels: Approved for use with both natural gas,
and propane. Approved as is for use at 0' to
4,500' (0-1370m).
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 127 CFM.
Log Set: Ceramic fibre, 8 per set.
Vent System: 3" co-linear aluminum flex.
INSTALLATION
INSTALLATION INTO A
SOLID FUEL BURNING
FIREPLACE OR
FACTORY BUILT
FIREPLACE
The E33 Gas Inserts have been tested and ap-
proved to be vented into any masonry fireplace
or approved solid fuel burning factory built
fireplace that will allow the insert to physically
fit into the firebox. Refer to page 6 for minimum
fireplace clearances.
If the factory built fireplace* height is too low
for your Insert, you may remove the smoke
baffle plate and damper from the factory
built fireplace as long as these items are
saved and are reinstalled in the event that
the Insert is removed. NOTE:Any alterations
made to the listed solid fuel burning factory
built fireplace may void the listing of the
fireplace. Cutting any sheet-metal parts of
the fireplace, in which the gas fireplace insert
is to be installed, is prohibited.
If the factory-built fireplace has no gas ac-
cess hole(s) provided, an access hole of
1.5" (37.5mm) or less may be drilled through
the lower sides or bottom of the firebox in
a proper workmanship like manner. This
access hole must be plugged with non-com-
bustible insulation after the gas supply line
has been installed.
The fireplace and fireplace chimney must be
clean and in good working order and con-
structed of non-combustible materials and
chimney cleanouts must fit properly. Refrac-
tory, glass doors, screen rails, screen mesh,
and log grates can be removed from the
fireplace before installing the gas fireplace
insert. Smoke shelves, shields and baffles
may be removed if attached by mechani-
cal fasteners. A tight connection between
the gas fireplace insert flue collar and the
fireplace chimney must be made.
*Check with your local inspector before com-
mencing with this installation.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are
required by the Canadian Safety Standards
and ANSI Standards to make you aware of
the following:
General Safety Information
1) The appliance installation must conform
with local codes or in the absence of local
codes, with CAN/CSAB149.1 (in Canada)
or the National Fuel Gas CodeANSI Z223.1
NFPA54 in the U.S.A. This appliance should
be installed by a qualified gas fitter technician
only.
2) Installation and repair should be done
by a qualified service person.
3) The appliance should be inspected
before use and at least annually by a
professional service person. More fre-
quent cleaning may be required due to
excessive lint from carpeting, bedding
material, animal hair, etc. It is impera-
tive that control compartments, burners
and circulating air passageways of the
appliance be kept clean.
4) See general construction and assembly
instructions. This appliance may only be
installed in a vented, noncombustible fire-
place.
5) This appliance is Listed for bedroom instal-
lations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
6) Always connect this appliance to a vent
system vent that is run (or routed) to the
outside of the building envelope. Never vent
to another room or inside a building. Make
sure that the vent is properly sized and is
of adequate height to provide the proper
draft.
7) Inspect the venting system annually for
blockage and any signs of deterioration.
8) Any glass removed for servicing must be
replaced prior to operating the appliance.
9) WARNING: Failure to position the parts
in accordance with the diagrams in this
manual or failure to use only parts specifi-
cally approved with this appliance may
result in property damage or personal
injury.
10) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.

6E33 FPI Direct Vent Gas Insert
14) Install optional Excalibur Surround. See
page 15.
15) Install optional remote control or wall ther-
mostat, pages 17.
16) Final check (page 18): Before leaving this
unit with the customer, the installer must
ensure that the appliance is firing correctly.
This includes:
a) Clocking the appliance to ensure the
correct firing rate.
b) Adjusting the primary air, if required,
to ensure that the flame does not
carbon. See page 9.
c) Ensuring that the appliance is venting
correctly.
MATERIALS
REQUIRED
No electrical power supply is required for the gas
control to operate. A 120 Volt AC power cord is
hooked up to the fan. Plug the 3 wire cord into
a suitable receptacle. Do not cut the ground
terminal off under any circumstances. When
connected with 120 volts, the appliance must
be electrically grounded in accordance with
local codes, current version of the Canadian
Electrical Code CSA C22.1 (in Canada) or in
the absence of local codes, with the National
Electrical Code ANSI/NFPA 70.
NOTE: This unit is equipped with a heat
sensor thermodisc which will prevent the
blower from operating until the unit reaches
the correct temperature.
INSTALLATION
11) Due to high temperatures, the appliance
should be located out of high traffic areas
and away from furniture and draperies.
Children and adults should be alerted to
the hazards of high surface temperatures,
especially the fireplace glass, and should
stay away to avoid burns or clothing ignition.
Young children should be carefully super-
vised when they are in the same room as
the appliance. Clothing or other flammable
material should not be placed on or near
the appliance.
INSTALLATION
CHECKLIST
Before installing vent system ensure that the
damper plate is open and secure to prevent
the damper plate from falling down and crush-
ing the liner.
The FPI Gas Insert is installed as listed
below.
1) Check all clearances to combustibles, see
page 7.
2) Make the gas connection. See page 8.
3) Install the 3" flue liner to the sliding connector
plate. See page 8.
4) Slide the unit half way into the fireplace.
5) Pull the vent connector plate through the
tapered brackets and fasten to the front
plate. See page 8.
6) Slide the unit fully into the fireplace.
7) Test gas pressure, page 9. Check aeration
system, page 9.
8) Install the optional brick panels. See page
9.
9) Install the log set. See page 10.
10) Assemble and install the faceplate and trim.
See page 13.
11) Install the standard flush door. See
page 14.
12) Install both louvers. See page 14.
13) Install optional full screen doors. See page
16.
MINIMUM FIREPLACE
OPENING
The minimum fireplace opening for the FPI
gas fireplace insert is shown in the following
diagrams:
WARNING:
Electrical Grounding Instructions
This appliance is equipped with
a three pronged (grounding) plug
for your protection against shock
hazard and should be plugged
directly into a properly grounded
three-prong receptacle. Do not cut
or remove the grounding prong
from this plug.
NOTE: If you are installing the Excali-
bur, the minimum fireplace dimensions
are as follows:
Width (at front): 34-1/2" (876mm)
Depth: 17-3/4" (451mm)
Height: 26" (660mm)
MINIMUM FIREPLACE
OPENING EXCALIBUR
OPTION
The minimum fireplace opening for the FPI
gas fireplace insert is shown in the following
diagrams:
Emissions from burning wood or gas could
contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects or other
reproductive harm.

7
E33 FPI Direct Vent Gas Insert
MINIMUM CLEARANCES TO COMBUSTIBLES
From Unit
Side Walls * A 8" (203 mm)
Ceiling B47" (1194 mm)
Min. Mantel Height C 15" (381 mm)
Max. Mantel Depth D 3-1/2" (89 mm)
Alcove Width E 76" (1930 mm)
Alcove Depth F 36" (914 mm)
Hearth Height G 1-1/4" (32 mm)
Hearth Width H 45-1/2" (1156 mm)
Hearth Depth I 13" (330 mm)
* Alcove side wall must have a min. of 8"
clearance on one side.
REGENCY FLUSH
COMBUSTIBLE MANTEL CLEARANCES
EXCALIBUR SURROUND & FULL SCREEN DOORS
COMBUSTIBLE MANTEL CLEARANCES
Mantel can be installed anywhere in shaded area or higher using the above scale.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.
Because of the extreme heat this fireplace emits, the mantel clearances are critical.
Combustible mantel clearances from top of unit are shown in the above diagrams.
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible
board.
INSTALLATION

8E33 FPI Direct Vent Gas Insert
VENTING
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. The flue length
must be a minimum length of 8 ' (2.44m) and
a maximum of 35' (10.7m). See chart above
for minimum distances from roof. Periodically
check that the vent is unrestricted.
Masonry chimneys may take various contours
which the flexible liner will accommodate.
However, keep the flexible liner as straight
as possible, avoid unnecessary bending.
Part # Description
948-305 3" Flex - 35 ft.
946-529 FPI Co-linear DV Vertical
Termination Cap
Alternate Approved Caps
980 Vertical Termination Cap
991 High Wind Cap
923GK 3" Co-linear Adaptor with
flashing
GAS CONNECTION
GAS CONNECTION WARNING:
Only persons licensed to work
with gas piping may make the
necessary gas connections to
this appliance.
1) If the appliance is to be installed into an
existing chimney system, thoroughly clean
the masonry or factory built fireplace.
2) The appliance is provided with an opening
on the left hand side of the control compart-
ment. A 3/8" NPT gas supply pipe must be
brought near this inlet hole.
In areas of consistently high winds, we recom-
mend using the Simpson Dura-Vent System
(923GK adapter and 991 high-wind cap).
The Air Intake pipe must be attached to the inlet
air collar of the termination cap.
INSTALLATION
3) Locate the center point where the vent will
pass through the chimney above the ap-
pliance. Move the appliance into the exact
location where it is to be installed. Ensure
that the Insert is level.
FLUE LINER
INSTALLATION
1) Cut the flex liner as required.
2) Mark the end of one liner to indicate
Exhaust.
3) Connect the other end of the above liner to
the exhaust side of the termination adap-
tor, seal connection with high temperature
silicone. Secure with gear clamp.
4) Connect the 2nd liner to the inlet side of the
adaptor, seal connection with high tempera-
ture silicone. Secure with gear clamp.
5) Install flashing.
6) Insert both liners into chimney, passing
through the damper opening.
7) Install termination cap.
8) Connect the marked end of the liner to the
exhaust collar of the vent connector plate
marked with an "E", seal connection with
high temperature silicone. Secure with gear
clamp.
9) Connect the 2nd liner to the intake collar, seal
connection with high temperature silicone.
Secure with gear clamp.
NOTE:
1) Final gas connection should be made after
unit is in place to avoid damage to line when
pushing the unit into position.
2) Mill-pac may be used instead of high
tempture silicone and screws may be used
instead of gear clamps at connections of
liner to inlet and vent collars.
10) Align vent connector plate with guides on
unit.
11) Slide unit into masonry opening, while ensur-
ing that the slot at the rear of the connector
plate mates up with the hold down plate on
the unit.
12) Secure with Screw.

9
E33 FPI Direct Vent Gas Insert
OPTIONAL
BRICK PANEL
Optional Brick Panel Set:
Part # Description Qty
Top (brick) panel 1
Back (brick) panel 1
Left (brick) panel 1
Right (brick)panel 1
340-043 Top bracket 1
340-094 Bottom clips 2
511-031 Brick clips 2
Diagram 1
GAS PIPE
PRESSURE TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig.
(3.45 kPa). Disconnect piping from valve at
pressures over 1/2 psig.
The manifold pressure is controlled by a regu-
lator built into the gas control, and should be
checked at the pressure test point.
NOTE: To properly check gas pressure, both
inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.
1) Make sure the valve is in the "OFF" posi-
tion.
2) Loosen the "IN" and/or "OUT" pressure
tap(s), turning counterclockwise with a 1/8"
wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
6) When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
flat screwdriver. Note: Screw should be
snug, but do not over tighten.
INSTALLATION
GAS INSERT
AERATION SYSTEM
The air shutter can be adjusted by moving the
adjusting wire up or down. The wire is accessed
through the bottom louver opening. Open the air
shutter for a blue flame or close for a yellower
flame. The burner aeration is factory set but
may need adjusting due to either the local gas
supply or altitude.
Minimum Air Shutter Opening:
5/16" Natural Gas
7/16" Propane
CAUTION: Carbon will be produced if air
shutter is closed too much.
SIT Valve Description
1) Gas cock knob
2) Manual high/low adjustment
3) Pilot Adjustment
4) Thermocouple Connection - option
5) Manifold (Outlet) Pressure Tap
6) Inlet Pressure Tap
1234
5
6
IN OUT
Note: Any damage due to carboning result-
ing from improperly setting the aera-
tion controls is NOT covered under
warranty.
Note: Aeration Adjustment should only
be performed by an authorized FPI
Installer at the time of installation or
service.
Installation of Brick Panels:
1) Remove top louver and glass door if in-
stalled.
2) Remove the logs if they are already in
stalled. Note: the grate must be removed in
order to remove the bottom log. Ensure you
slide the bottom coal off to the right-hand
side to avoid chipping.
3) Unwrap the brick pattern panels from the
protective wrapping. Handle the panels with
care as they can break easily.
4) Remove the two screws from the bottom of
the baffle plate. Install the bottom clips onto
the baffle plate (refer to Diagram 1).
Bottom Clips
7) Pilot Outlet
8) Main Gas Outlet
9) Alternative TC Connection Point

10 E33 FPI Direct Vent Gas Insert
Top Bracket
5) Place the top bracket onto the top edge of
the top panel (refer to Diagram 2).
Diagram 2
6) Slide the top panel and bracket assembly
carefully onto the baffle plate ensuring the
panel is centered. Make sure the tabs of the
topbracket fitinto thebaffle openings (refer to
Diagram 3).
7) Insert the back panel by sliding it between
the sidewalls of the firebox and the rear log
support.
Diagram 3
8) Before installing the side brick panels, re-
move the screws from the side brick clips
(refer to Diagram 4).
Diagram 4
9) Insert the side panel by positioning it flat
against the side walls. Tilt the panel
towards the middle of the firebox, then insert
the bottom front corner. Repeat on the other
side.
10) Install the 2 brick retaining clips, one on
each side.
Final Installation
LOG INSTALLATION
WARNING: Dangerous operating condi-
tions may occur if these logs are not
positioned in their correct certified
locations. Read the following instruc-
tions carefully and refer to the attached
diagram.
Materials Required:
Complete Log Set (Part # 340-930)
Contains the following:
Description
03-17 Bottom Log
03-18 Center Top Log
03-19 Front Log
03-20 Left Log
03-21 Right Log
03-22 Left top Log
03-23 Rear Log
03-24 Right Top Log
Diagram 2
03-17
The "03" reference numbers (i.e. 03-23)
are molded into the rear of each log.
03-17
03-20
03-23
03-21
03-22 03-24
03-18
03-19
Instructions:
1) Remove and carefully unwrap the logs from
the box. Please handle with care and do not
force them into position to avoid chipping.
2) Remove the top louver and flush door if
installed (refer to page 14).
3) To remove the grate, loosen the two
Phillips screws which are securing
the grate. Slide the grate outwards
to remove it from the unit (refer to
Diagram 1).
Diagram 1
4) Angle log 03-17 and slide it between the
top and bottom burner tube under the “T”
section until it touches the left grate support
bracket (refer to Diagram 2).
INSTALLATION
Screws

11
E33 FPI Direct Vent Gas Insert
INSTALLATION
5) Re-install the grate (reverse step 3).
6) Line up the pin holes (located at the bottom
of log 03-23) to the pins of the rear log sup-
port and position them into place. (refer to
Diagram 3)
Diagram 3
03-23
Locating Pins
03-23
03-17
03-21
Diagram 5
7) Align the bottom grooves of log 03-21 onto
the right side of the grate and gently slide
the log back until it touches the locating tab
(refer to Diagram 4 & 5).
Diagram 4
Locating
Tab
03-21
12) Place log 03-19 over the left center of the
grate. Ensure the log set looks like Diagram
12.
11) Place log 03-24 over log 03-23 and log 03-21
ensuring the pin hole of log 03-24 lines up
with the right pin of log 03-23 and the right
pin of log 03-21 (refer to Diagram 11).
03-24
03-23
03-21
Locating
Pins
Diagram 11
Diagram 10
03-17
03-20
03-23
03-22
03-18
Tab
03-20
03-18
03-23
Locating
Pins
Diagram 9
10) Place log 03-18 over log 03-23 and log 03-20.
Ensurethepinholeoflog03-18linesupwiththe
middle pin of log 03-23 and the right pin of log
03-20 (refer to Diagram 9 & 10).
Diagram 8
03-22
Locating
Pins
03-23
03-20
8) Align and position the pin hole of log 03-20
down into the left locating pin of log 03-21.
Slide into the groove and gently place into
position until it touches the locating tab.
(see Diagram 6 & 7)
Diagram 6
Locating
Tab
03-20
Locating
Pin
03-21
9) Place log 03-22 over log 03-23 and
log 03-20. Ensure the pin hole of log
03-22 lines up with the left pin of log
03-23 as well as the left pin of log
03-20 (refer to Diagram 8).
Diagram 7
03-21
03-17
03-23

12 E33 FPI Direct Vent Gas Insert
INSTALLATION
Final Installation
03-19
E33 CONVERSION KIT FROM NG TO LPG
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
Conversion Kit Contains:
Qty. Part # Description
1 910-018 SIT Conversion Kit-50%
Turndown LPG
1 910-037 LPG (Pilot Orifice)
1 904-641 Burner Orifice #50
(rated at 35,500 BTU/HR)
1 908-255 Label "Converted to LPG"
1 904-529 5/32" Allen Key
1 918-415 Instruction Sheet
1 Red LPG Label
1 Silver "Converted to
LPG" Label
Instructions:
1) Shut off the gas supply.
2) Remove the louvers and flush door.
3) Remove the logs and grate (refer to p.10).
Ensure you slide the bottom log 03-17 off
to the right-hand side to avoid chipping.
4) Remove front base brick.
5) Remove burner by unscrewing the 2
screws.
6) Pull off the pilot cap to expose the pilot
orifice.
7) Unscrew the pilot orifice with the allen
key and replace with the LPG pilot orifice
provided in the kit, then replace pilot cap.
Burner Orifice Removal
11) Ensure that the rubber gasket (D) is properly
positioned. Install the new HI/LO pressure
regulator assembly to the valve using the
new screws (E) supplied with the kit. Tighten
screws securely.
12) Reverse steps 5) to 3).
13) Attach clear label "This unit has been
converted to LPG" near or on the serial #
decal. Attach silver label "This valve has
been converted from NG to LPG using SIT
conversion Kit Code 0.907.202" onto the
valve.
14) Replace yellow "NG" label with red "LPG"
label.
15) Check for gas leaks with a proper soapy
solution or leak detector.
16) Check for proper spark between the ignitor
and pilot cap. Refer to “Lighting Procedure”
(page 18) for lighting sequence.
17) Check pilot flames. Correct flame pattern
has 3 strong blue flames. Adjustment can
be made by turning the slotted screw at
the top right corner of the valve. Refer to
9) Reinstall new burner orifice LPG stamped
#50 and tighten.
10) Remove and discard the 3 pres-
sure regulator mounting screws (A),
pressure regulator (B) and diaphragm (C)
refer to Diagram 1.
8) Remove the burner orifice by using a 1/2"
wrench, while using a 9/16" wrench to hold
onto the elbow behind the orifice.

13
E33 FPI Direct Vent Gas Insert
Diagram 4
INSTALLATION
9) Attach the trim to the faceplate by using the
plated screws (refer to Diagram 4).
Rear View: Faceplate Assembly
Diagram 1
FACEPLATE & TRIM
INSTALLATION
1) Lay the faceplate panels flat, face down on
something soft so they don't scratch.
2) Take the top faceplate and align the holes
in it with the holes in the side panels. Us-
ing the screws provided, attach from the
top of the panel (the holes in the top panel
are slightly larger than the holes in the side
panel to facilitate easier installation). Refer
to Diagram 1.
Hint: Don't tighten the screws down com-
pletely at this point, continue on with steps
3 and 4 and do a trial fit to the unit. Make
any necessary adjustments and when it fits
properly then tighten down the screws.
Diagram 3
7) Tuck the wires into the faceplate to keep
them away from the insert using the clip
provided. Attach the clip to the rear of the
faceplate to ensure that the wires do not
touch the side of the unit. Refer to Diagram
3.
8) The power cord should be run behind the
faceplate panel.
4) Place the trim on the assembled faceplate
panels, aligning the wire connections from
the switches with the notch on the left side
panel.
5) Connect the fan switch wires by taking the
black and red wires with the male ends (in
the grey harness) and connect them with
the wire connectors from the fan speed
control.
6) Connect the ON/OFF switch wires by taking
the black and red wires with the female ends
and connect them to the ON/OFF switch.
“Maintenance Instructions” (page 20) for
correct flame patterns.
18) Check inlet (12” WC min) and outlet (11”
WC) pressures. Refer “Gas Pipe Pressure
Testing” (page 9).
19) Check operation of flame control.
20) Check for proper flame appearance and
glow on logs.
Diagram 1
Installer Notice:
These instructions must be
left with the appliance.
Rear View: Trim Assembly
Diagram 2
3) Using the connectors provided, join the left
side trim (with the ON/OFF switch) to the
top trim. Diagram 2. Connect the right side
trim to the top trim.
Pilot
Adjustment
Screw
WARNING:
This conversion kit shall be installed by a
qualified service agency in accordance with
the authority having jurisdiction. If the infor-
mation in these instruction is not followed
exactly, a fire, explosion or production of
carbon monoxide may result causing prop-
erty damage, personal injury or loss of life.
The qualified service agency is responsible
for the proper installation of this kit. The
installation is not proper and complete until
the operation of the converted appliance is
checked as specified in the manufacturer’s
instructions supplied with the kit.
Note: Equipped for Altitude 0-4500 ft.
(0-1370m).

14 E33 FPI Direct Vent Gas Insert
INSTALLATION
Diagram 5
11) Push the FPI logo plate into the two holes
in the bottom left corner of the faceplate.
The standard flush door comes with a black
frame. To install the frame, simply hook the top
door flange onto the top of the unit and swing
the door towards the unit, (Diagram 1 and 2).
Be careful that the glass gasket does not roll up;
there must be a gap between the gasket and
the door lip to ensure that the door sits securely
on the unit. Refer to Diagram 3.
10) Attach the faceplate panels to the insert
body using the 4 remaining black screws.
Refer to Diagram 5.
STANDARD
FLUSH DOOR
Diagram 3
Secure door by fastening with two screws located
at bottom of glass frame (refer to Diagram 1).
Diagram 2
To remove the flush door, reverse the above
steps.
FLUSH LOUVERS
2) Install the Spring Hinges on the left and right
side of the bottom of the Firebox using 2
screws per hinge.
3) Place the Bottom Louver near the hinge. Flip
hinge over the Bottom Louver and secure
using 3 screws.
Bottom Louver
Hinge
Location
1) The top louver is held in place by friction fit.
Refer to Diagram 1
Diagram 1
4) Install the Top Frame by hooking it onto the
two screws at the top of the full screen door.
It is held in place by magnets.
Top Frame
Screw
1) Hold the full screen faceplate up against
the unit in order to make the following wire
connections.
Pull the ON/OFF connector wires thru the
box and connect them to the switch.
Connect the fan switch wires with the wire
connectors from the fan speed control. Place
clips over wires and tuck into side trim.
FULL SCREEN FRONT
2) Lift the unit up slightly and push down on
the corners of the Bottom Trim Bracket and
slide under unit.
3) Completely secure faceplate to the unit by
securing 4 screws to the Left and Right Side
Trim.
Bottom Trim
Bracket
Push in Corners
Screws
Diagram 1

15
E33 FPI Direct Vent Gas Insert
1) Align the left side Faceplate Trim Bracket
with the Firebox Flange and secure using
2 screws as shown in diagram 1. Repeat
for right side.
Faceplate
Trim Bracket
Firebox
Flange
IMPORTANT NOTE:
When using the Surround, the unit must be set 1"
further into the fireplace than the standard face-
plate installation. See page 6 for the Minimum
Fireplace Opening Excalibur Option.
Diagram 1
2) Push the Blanking Plate down on top of the
Glass Door (refer to Diagram 2).
Blanking Plate
Top of
Glass
Door
INSTALLATION
EXCALIBUR SURROUND
INSTALLATION
6) Place Bottom Frame near hinge. Flip hinge
over Bottom Frame and secure with 3 screws
each.
5) Install Spring Hinges to the Left and Right
Side of the bottom of the firebox using 2
screws per hinge.
Bottom
Frame
Hinge Location
7) Install the Left and Right Side Screen Doors
by placing over top of the hinges on the
faceplate. Hold the door at a 45 degree
angle to avoid scratching the faceplate.
8) Close screen doors.
Hinge
Screen Door
3) Hold the Faceplate Trim up against the unit
in order to make the following wire connec-
tions.
3a) Pull the ON/OFF connector wires from the
firebox and connect them to the switch.
3b) Connect the fan switch wires with the wire
connectors from the fan speed control. Place
clips over wires and tuck into side trim.
for gas
connection Self-adhesive
wire clip
ON/OFF
switch
wires to
ON/OFF
switch wires to
Fan switch
connectors
Fan Speed
Switch
(Rear View)
4) Secure the Faceplate by sliding the slots in
the Faceplate into the flanges on the left and
right side Faceplate Trim Brackets. Once the
Faceplate is in place secure using 2 screws
per side.
Faceplate
Slots
Faceplate
Trim Bracket
NOTE: If you are installing the
Excalibur, the minimum fireplace
dimensions are as follows:
Width (at front): 34-1/2" (876mm)
Depth: 17-3/4" (451mm)
Height: 26" (660mm)
Diagram 2

16 E33 FPI Direct Vent Gas Insert
INSTALLATION
1) Remove the rivets from the surround by
pulling off the hoseclamp (located at the
backside of surround) with a screwdriver or
plyer. Re-install the rivets by putting them
through the holes on the sides of the sur-
round.
3) Remove the handles by removing the nut
and screw. Install the new handles by plac-
ing them in position over the holes on the
surround louver. Put the screws through
the holes and secure them by tightening
them with a nut.
2) Take the hoseclamps and put them over the
back of each rivet. Squeeze the hoseclamp
to secure onto rivets ensuring that the
hoseclamp is touching the back side of
the surround. The hoseclamp can now be
released.
4) Place the emblem over the emblem design
on the surround. Insert the studs through the
holes. To secure them first put on the split
lock washer and then the nut and tighten.
DOUBLE DOOR OPTION
Remove the handles by removing the nut
and screw. Install the new handles by plac-
ing them in position over the holes on the
door(s). Put the studs through the holes
and secure them by tightening them with a
nut.
5) Place the bottom hooks of the Surround into
the bottom slots of the Faceplate. Slightly
pull up the Surround and push the top hooks
into the top slots of the Faceplate. Push
down to secure. Tug on the Surround to
ensure it is securely locked in place.
Backside of
Surround Shown
Hooks
Faceplate Slots
Surround
Faceplate
ACCENT KIT
INSTALLATION
5) Remove the 2 studs on the sides of the Hood.
Insert the new studs through the holes and
secure them by first putting on the washer
and then tighten with a nut.
OPTIONAL SCREEN
DOORS
1) Attach door bracket to sides using 4
screws.
Door Bracket
attaches with
2 screws on
each side.
Double Screen Door: attach to left and right
side of unit.
2) Slide the door(s) onto the hinges.
Left Side
Faceplate Bracket
Trim Flange

17
E33 FPI Direct Vent Gas Insert
WIRING DIAGRAM
INSTALLATION
This heater does not require a 120VA.C. supply
for operation. However, a 120VA.C. power sup-
ply is needed for the fan/blower operation.
WARNING: Electrical Grounding Instructions
This appliance is equipped with a three pronged
(grounding) plug for your protection against shock
hazard and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or remove
the grounding prong from this plug.
Caution: Ensure that
the wires do not touch
any hot surfaces and
are away from sharp
edges.
Use the FPI Remote Control Kit approved for
this unit. Use of other systems may void your
warranty.
The remote control kit comes with a hand held
transmitter, a receiver and a wall mounting
plate.
1) Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace to
that location. Use Thermostat Wire Table.
2) Connect the wires as per the wiring diagrams
below.
CAUTION
Do not connect the millivolt
remote control wires
to the 120V wires.
3) Install 3 AAA alkaline batteries in transmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
OPTIONAL REMOTE CONTROL OPTIONAL WALL
THERMOSTAT
A wall thermostat may be installed if desired,
follow the wiring diagram below. Note: the wires
are connected to the "TH" on the gas valve. Use
the table below to determine the maximum wire
length. FPI offers an optional programmable
thermostat but any 250-750 millivolt rated non-
anticipator type thermostat that is CSA, ULC
or UL approved may be used.
It is recommended that the thermostat be
installed on an interior wall.
CAUTION
Do not connect the millivolt
wall thermostat wires
to the 120V wires.
H
I
L
O
O
F
F
O
N
PI
L
O
T
TP TH
To wall switch,
remote control
or thermostat
To thermopile
THTP
CAUTION: Label all wires prior to dis-
connection when servicing controls.
Wiring errors can cause improper and
dangerous operation.

18 E33 FPI Direct Vent Gas Insert
OPERATING INSTRUCTIONS
2) Turn gas control knob so indicator points
to "OFF" position and allow 5 minutes for
any gas in the combustion chamber to
escape.
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the ignitor button several times until the
pilot lights. After approximately one minute,
release the gas control knob. The pilot flame
should continue to burn. If the pilot does not
remain lit, repeat operation allowing a longer
period before releasing gas control knob.
4) When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON" posi-
tion.
5) Reinstall the glass door (refer to page 14).
6) Use the switch, thermostat or remote control
to turn on the unit.
7) Rotate the flame height regulator to adjust
the flame height higher or lower.
SHUTDOWN
PROCEDURE
1) Use the switch, thermostat or remote control
to turn off the main burner.
2) Turn the main gas control clockwise to the
"OFF" position to turn off the pilot.
3) Turn off all electric power to appliance if
service is to be performed.
FIRST FIRE
The first fire in your stove is part of the paint
curing process. To ensure that the paint is
properly cured, it is recommended that you
burn your fireplace for at least four (4) hours
the first time you use it with the fan on. When
first operated, the unit will release an odour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at
this time. Open a few windows to ventilate the
room for a couple of hours.
The glass panel may require cleaning after the
unit has cooled down.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS HOT.
Note: When the glass is cold and the appli-
ance is lit, it may cause condensation
and fog the glass. This condensation
is normal and will disappear in a few
minutes as the glass heats up.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
OPERATING
INSTRUCTIONS
1) Read and understand these instructions
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
4) Make sure the glass in the door frame is
properly positioned. Never operate the ap-
pliance with the glass removed.
5) Verify that the venting and cap are unob-
structed.
6) Ensure that the brick panels, if used, are
installed.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
LIGHTING
PROCEDURE
IMPORTANT: Gas cock knob cannot be
turned from "PILOT" to "OFF" unless it is
partially depressed.
1) Turn burner OFF using "ON/OFF" switch.
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size Max. Length
Thermostat Wire Table
FINAL CHECK
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly. This includes:
1) Clocking the appliance to ensure the cor-
rect firing rate (rate noted on label) at 15
minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow
the unit to burn for 15 min. to stabilize.
3) Check for proper draft.
CAUTION
Any alteration to the product that
causes sooting or carboning that
results in damage to the exterior
facia is not the responsibility of
the manufacturer.
During the first few fires, a white film
may develop on the glass front as part
of the curing process. The glass should
be cleaned or the film will bake on and
become very difficult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
IMPORTANT
Prior to igniting or reigniting the
pilot, remove the glass door.
Only when the pilot holds, without pressure
being applied to the control knob, should you
reinstall the glass door. The unit must not be
operated with the glass door removed.

19
E33 FPI Direct Vent Gas Insert
OPERATING INSTRUCTIONS
COPY OF LIGHTING INSTRUCTION PLATE AUTOMATIC
CONVECTION
FAN OPERATION
The fan operates automatically. Turn the knob on
the side of the faceplate to adjust to the desired
speed. The fan will turn on as the stove comes
up to operating temperature. After the unit has
been turned off and the unit has been cooled
to below useful heat output range, the fan will
shut off automatically.
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly normal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listed below are some examples.All are normal
operating sounds and should not be considered
as defects in your appliance.
Blower:
FPI gas appliances use high tech blowers to
push heated air farther into the room. It is not
unusual for the fan to make a "whirring" sound
when ON. This sound will increase or decrease
in volume depending on the speed setting of
your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a differ-
ent gauge material from the rest of the firebox
and body. Therefore, the varying thicknesses of
steel will expand and contract at slightly different
rates which can cause "ticking" and "cracking"
sounds. You should also be aware that as there
are temperature changes within the unit. These
sounds will likely re-occur. Again, this is normal
for steel fireboxes.
Blower Thermodisc:
When thermally activated switch turns ON, it
will create a small "clicking" sound. This is the
contact switch closing.
Pilot Flame:
While the pilot flame is on it will make a slight
"whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be heard. This is normal
operation of a gas regulator or valve.
Unit Body and Firebox:
Different types and thicknesses of steel will ex-
pand and contract at different rates resulting in
some "cracking" and "ticking" sounds which will
be heard throughout the cycling process.

20 E33 FPI Direct Vent Gas Insert
MAINTENANCE
GENERAL VENT
MAINTENANCE
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or streaks,
and in extreme cases, holes. These com-
ponents should be replaced immediately.
2) Remove the Termination Cap, and shine a
flashlight down the Vent. Remove any bird
nests, or other foreign material.
3) Check for evidences of excessive condensa-
tion, such as water droplets forming in the
inner liner, and subsequently dripping out the
joints. Continuous condensation can cause
corrosion of caps, pipe, and fittings. It may
be caused by having excessive lateral runs,
too many elbows, and exterior portions of the
system being exposed to cold weather.
4) Inspect joints to verify that no pipe sections
or fittings have been disturbed, and conse-
quently loosened. Also check mechanical
supports such as Wall Straps, or plumbers'
tape for rigidity.
LOG REPLACEMENT
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door to carefully remove the
logs. The pilot light generates enough heat to
burn someone. If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagram under Log
Installation.
NOTE: Improper positioning of logs may create
carbon build-up and will alter the unit’s perform-
ance which is not covered under warranty.
GLASS GASKET
If the glass gasket requires replacement use
a tadpole gasket for the Flush Front (Part #
936-155).
STEEL OR GOLD TRIM
The steel or 24 carat gold plated finish on the
louvers requires little maintenance, and need
only be cleaned with a damp cloth. DO NOT use
abrasive materials or chemical cleaners, as they
may harm the finish and void the warranty.
Clean any fingerprints off before turning the
unit on. If the top louvers start to discolour,
check the door gasket seal and replace if
necessary.
Top view of pilot flame
Top View of pilot flame
Incorrect flame pattern will have small, probably
yellow flames, not coming into proper contact
with the rear of the burner or thermopile.
6) Each time the appliance is lit, it may cause
condensation and fog the glass. This
condensation and fog is normal and will
disappear in a few minutes as the glass
heats up.
Never operate the appliance without the
glass properly secured in place or with
the door open.
7) Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace nay part of the control system
and any gas control which has been under
water.
8) Periodically check the pilot flames. Correct
flame pattern has three strong blue flames: 1
flowing around the thermopile and 1 around
the thermocouple, and 1 flowing across the
front of the burner.
Note: If you have an incorrect flame pattern,
contact your FPI dealer for further
instructions.
CLOTHING OR OTHER FLAM-
MABLE MATERIAL SHOULD NOT
BE PLACED ON OR NEAR THE
APPLIANCE.
WARNING: CHILDREN AND
ADULTS SHOULD BE ALERTED
TO THE HAZARDS OF HIGH
SURFACE TEMPERATURE AND
SHOULD STAY AWAY TO AVOID
BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD
BE CAREFULLY SUPERVISED
WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE.
CAUTION: ANYSAFETY SCREEN
OR GUARD REMOVED FOR
SERVICING AN APPLIANCE
MUST BE REPLACED PRIOR TO
OPERATING THE APPLIANCE.
MAINTENANCE
INSTRUCTIONS
1) Always turn the gas valve to the off posi-
tion before cleaning. For relighting, refer to
lighting instructions. Keep the burner and
control compartment clean by brushing and
vacuuming at least once a year.
When cleaning the logs, use a clean soft
paint brush as the logs are fragile and easily
damaged.
2) Clean (never when unit is hot) appliance,
door and louvers with a damp cloth. Never
use an abrasive cleaner. The optional finish-
es on louvers and doors may be scratched
if abrasives are used to clean them. The
heater is finished in a heat resistant paint
and should only be refinished with heat
resistant paint (not with wall paint). FPI uses
StoveBrite Paint - Metallic Black #6309.
3) Make a periodic check of the burner for
proper position and condition. Visually
check the flame of the burner periodically,
making sure the flames are steady: not
lifting or floating. If there is a problem, call
a qualified service person.
4) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
During the annual service call, the burners
should be removed and cleaned from the
burner tray.
5) Keep the area near the appliance clear and
free from combustible materials, gasoline
and other flammable vapours and liquids.
Front Burner Tube
Front Burner Tube