Frama Permanent Furniture WD-1 10000 User manual

WD-1
Specifications
Design Chris Liljenberg Halstrøm
Year 2013
Typology Table
Collection Permanent Furniture
Origin Lithuania
Material Tops Solid natural oak - natural
oiled
Material Base Powder coated steel
Assembly Top and base flat packed
Product Item No. EAN code
WD-1: Writing desk 10000 5712828071005
WD-1: Steel Frama 10010 5712828071004
700 1200
659750

Contents:
Needed Tools:
Assembly:
In this box you will find:
- 1 H shaped crossbar
- 2 diagonal crossbars
- 2 welded legs
- 2 front horizontal crossbars
- 1 solid oak top, natural oiled
- 12 hex top screws
- 6 screws for wood top
- hex key
- cross head screwdriver
For regular cleaning, dust writing desk regularly and wipe with a
clean damp cloth. Follow maintenance for oiled oak top accord-
ing to further instructions.
Start by screwing the welded diagonal cross supports with H
shaped crossbar.
From here, screw the two welded legs on either side, making
sure to attach the three rods at each end of the initial construc-
tion.
Put the longer front horizontal cross bars in place, screwing in
place, then tightening all bolts as necessary.
Place the wood table top in position, screw in place from below.
WD-1 Assembly & Maintenance
1
3 4
2

Maintenance of Metals
Cleaning & Polishing Brass & Copper:
Cleaning Powder coated Steel/Aluminum:
Waxing Untreated Steel:
Same of the metals in the Frama collection are left untreated to allow for a natural patina
to develop over time. See below to keep these beautiful signs of aging, or polish them away.
All collection pieces are for indoor use.
Brass: Wash the brass with soapy water. To get rid of dirt or oil, mix a mild detergent with
warm water. Dip a soft cloth into the soapy water, and wipe the piece down with the cloth.
To polish brass, apply brass polish to a cloth, and rub it into the brass. Then use a dean,
dry cloth while rubbing the brass to create shine.
Copper: Squeeze a lemon and sprinkle salt over the copper, and rub to remove any tar-
nishing. Rinse the copper, and dry with a soft, dry cloth.
To dean powder coated furniture, carefully remove any loose deposits with a wet sponge.
Use a soft brush (non abrasive) or cloth, and a mild household detergent solution to re-
move dust, salt and other deposits. Rinse off with clean fresh water.
Then use a clean, soft cloth to dry the piece.
Since wax is only a coating and doesn’t actually bind with steel, it must be periodically
reapplied. As long as the piece is indoors, the wax will typically last at least a few years.
1. Use mineral spirits to clean the steel before application.
2. Using warm, dear wax, rub a thin layer over the steel with a soft cloth.
3. Using a dean cloth, buff out all of this dull wax with circular motions.
4. When the wax has been sufficiently buffed, the dullness will be gone, replaced with a
slight shine. The finished wax should feel smooth and slippery to the touch.

Cleaning & Maintenance of Oiled Wood Furniture
Cleaning:
Note:
Oiling Treatment:
Regular maintenance of oiled wooden furniture is both easy and efficient for long term use.
To achieve an optimal result we recommend oiling your product twice a year. We recom-
mend a natural wood oil. All collection pieces are for indoor use.
Daily cleaning is done with a soft cloth wrung out in clean water. Avoid using cleaners
containing any type of chemicals on the furniture.
End grain (edges), should by treated extra frequently to avoid dryness and cracking in the
dry season (winter). Irregular distribution of moisture in the wood can cause unnecessary
cracks and gap. To avoid this we recommend oiling both the top and underside of the furni-
ture. Be aware that oily rags can ignite spontaneously. Rags and papers used in the oiling
process will be flammable. Air dry after use.
1. Clean the furniture using a clean cloth dampened with warm water.
2. Once the furniture is dry, apply oil to a clean soft cloth or sponge - do not pour the oil
directly on the wood
3. Rub the oil into the wood in the direction of the grain, treating the entire surface of the
furniture piece.
4. Let the oil soak for about two hours, then remove any excess oil with a soft clean dry cloth.
5. Rub the surface with a clean soft cloth until a uniform surface is obtained, then let dry.