FRANCO BELGE The Belfort 54 05 06 User manual

Technical manual
to be saved
by the user
for future reference
Document n° 963-3 ~ 17/05/2001
Les Fonderies Franco-Belges
59660 MERVILLE
Phone : [phone]
Fax : [phone]
RC Hazebrouck 445750565B
Subject to modifications
The Belfort
Balanced flue Gas stove
EN 613.
Model : 154 05 06
Natural gas (type G20)
Type : I2E+ (FR) / I2H (GB).
Réf. : 154 05 07
Propane (type G31)
Type : I3P.
Description of the appliance
Installation instructions
Operating instructions
Spare parts
Warranty certificate
Français
English

Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Package . . . . . . . . . . . . . . . . . . 3
General characteristics . . . . . . . . . . 3
Description . . . . . . . . . . . . . . . . . 4
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Siting the appliance . . . . . . . . . . . . 5
Flue connection . . . . . . . . . . . . . . 6
Ventilation (G.B. Only) . . . . . . . . . . 7
Connecting the gas supply . . . . . . . . 7
Pressure testing . . . . . . . . . . . . . . 7
Coals layout . . . . . . . . . . . . . . . . 8
Service section . . . . . . . . . . . . . . . 9
User instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Important Notes . . . . . . . . . . . . . . 10
Data information . . . . . . . . . . . . . . 10
Operating the stove . . . . . . . . . . . . 10
Safety mechanisms . . . . . . . . . . . 11
Cleaning . . . . . . . . . . . . . . . . . 11
Servicing . . . . . . . . . . . . . . . . . 11
Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CONTENTS Page Page
FRANCO BELGE congratulates you on your choice.
FRANCO BELGE, which has been granted the ISO 9001 certification, guarantees the
quality of its appliances and is committed to meet its customers needs.
FRANCO BELGE, which can boast a 75-year experience in the industry of heating devices,
uses state-of-the-art technologies
to design and manufacture its whole range of products.
Balanced flue Gas stove Model. 154 05 06 / 154 05 07

WARNING
The appliance must be installed in compliance with Current Building Regulations.
Incorrectly installed, this appliance can be dangerous
and possibly cause serious accidents.
The manufacturers responsibility shall be limited to the supply of the equipment. ❑
1.Product information
1.1. Package
•1 package : Stove complete.
The ceramic coals are supplied inside the combustion
chamber.
•1 package : Balanced flue
1.2. Optional equipment
Balanced flue elbow 135° (code 72630).
1.3. General characteristics
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 05 06 . . . . . . . 154 05 07
GAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Natural gas . . . . . Propane LPG
Type/category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G20 / I2H . . . . . . . G31 / I3P
Gross calorific value (heat input) . . . . . . . . . . . . . kW . . . . . . . . . 4.2 . . . . . . . . . . 3.9
Nominal output . . . . . . . . . . . . . . . . . . . . . . . kW . . . . . . . . . 3 . . . . . . . . . . . 3
Supply pressure . . . . . . . . . . . . . . . . . . . . . mbar . . . . . . . . . 20 . . . . . . . . . . . 37
Burner pressure . . . . . . . . . . . . . . . . . . . . . mbar . . . . . . . . 18,5 . . . . . . . . . 35,5
Gas rate . . . . . . . . . . . . . . . . . . . . . . . . . m3/h . . . . . . . . 0,44 . . . . . . . . . 0,16
Injector size . . . . . . . . . . . . . . . . . . . . . . . bray . . . . . . . 18 / 280 . . . . . . . 18 / 120
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . Kg . . . . . . . . . 55 . . . . . . . . . . . 55
420
550
409
398
Ø 153
Figure 1 - Dimensions in mm
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 3

1.4. Description
The Belfort balanced flue stove has been individually
designed to add traditional charm and character to your
home. Providing a highly efficient heat source, the
appliance has the look and charm of a ‘real’ stove
coupled with the convenience of clean burning gas.
The stove is designed to run off Natural or LPG gas. It
is important to note that once a type of gas has been
specified the stove cannot run off any other type. The
type of gas that your stove is capable of burning is
stated on the data information panel under the stove.
The appliance is a “Balanced flue gas stove”, which is
a term used to describe a sealed combustion system in
which the inlet air and exhaust gases enter and exit
through two separate concentric passageways within
thesamesealedventsystem.
The Balanced flue system allows the gas appliance to
be vented directly to the outside atmosphere through a
suitable outside wall, unlike conventional venting
systems that take the inlet air from the room and vent
the exhaust vertically through the roof to the
atmosphere.
1
2
3
4
5
6
7
3
8
Figure 2 - Description
1: Balenced flue
2: Flue outlet
3: Air inlet
4: Ceramic coals
5: Coals support
6: Pilot
7: Burner
8: Protective grate
Balanced flue Gas stove Model. 154 05 06 / 154 05 07
4Technical manual

2.Installation instructions
This balanced flue gas stove is designed to run on
either natural gas or LPG. The burner unit is not
interchangeable between gas types.
The stove is a radiant convector fuel effect stove with a
balanced flue system. The Belfortcan be placeddirectly
inside any fireplace opening of the dimensions noted
within the installation instructions, providing it is on a
suitable outside wall.
These instructions have been compiled in accordance
with EN 613 1995.
It is required by law that any appliance using natural or
LPG gas is installed by a competent person (e.g.
CORGI registered), in conjunction with these
instructions and the requirements as laid down in the
following Regulations and British Standards :
-The Gas safety (Installation and Use) Regulations
1994 amended 1996.
-The Building Regulations (issued by the department of
the Environment).
-The Building Standards (Scotland) (Consolidation)
Regulations.
APPLIANCE TO BE INSTALLED IN ACCORDANCE
TO NATIONAL & LOCAL REGULATIONS.
Ensure that the stove corresponds to the type of gas
withwhichitistobeused.Thiscanbeconfirmedby
checking the data badge located underneath the
appliance.
All surfaces except the control knob are considered to
be working surfaces.
2.1. Siting the appliance
The appliance must be sited nextto an adjacentexterior
wall.
The gas supply connection to the appliance is at the
rear right hand side. The connection requires 8 mm
diameter semi-rigid pipe, not more than 1 metre in
length.
2.1.1. Clearance requirements
If the appliance has to be located in an opening, there
must be a clearance of at least 50 mm at the left hand
of the appliance, 50 mm at the back of the appliance
and 50 mm above from any non-combustible materials
(as shown in figure 3).
This distance must be extended to a mininum clearance
of 80 mm from any combustible materials.
There should ideally be a minimum gap of 150 mm at
the right hand side of the stove (this will ensure the best
possible access to the control knob).This measurement
may be reduced to a minimum gap of 100 mm if needed
however extra care should be taken when operating the
control knob when the appliance is hot.
A combustible shelf may be fitted over the appliance,
provided that in thecase of a150 mm orless deepshelf,
there is at least 250 mm clearance above the top of the
stove. The shelf depth may increase at the same rate
as the increase in clearance ; i.e. a shelf depth of
200 mm would require a clearance of 300 mm.
AB
100 250
150 250
200 300
250 350
300 400
2.1.2. Hearth
The stove must stand on a fireproof hearth.
To comply with the Building Regulations issued by the
Department of the Environment, the following points
should be noted when choosing a hearth :
a - The hearth must be made of non-combustible
material of thickness 12 mm minimum.
b - The hearth must protrude at least 150 mm in front of
the stove and 150 mm each side.
c - The hearth must not be capable of inadvertent
covering by a carpet or rug. This should be achieved by
either :
-the hearth being 50 mm above the level of the room
floor.
-a fender or kerb around the edge of the hearth to a
height of at least 50 mm above the floor.
150
150
150
5 0
n o n - c o m b u s t i b l e = 1 0 0
100
5 0
D E P T H
A *
c o m b u s t i b l e = B *
S h e l f
5 0
Figure 3
Minimum clearances to non-combustible materials,
hearth and shelf (in mm)
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 5

G
A
E
B,C
FF
J
H,I D
F
K
L
G
A
H,I
D
KF
J
Figure 4 - Balanced flue terminal locations
Dimension Terminal Position Minimum
Distance (mm)
A Directly below an
openable window or other
opening e.g. air brick
300
B Below gutters, soil pipes
or drain pipes 300
C Below eaves 300
D Below balconies or car
port roofs 600
E From vertical drain pipes
and soil pipes 75
F From internal or external
corners 600
G Above ground, roof or
balcony level 300
H From a surface facing a
terminal 600
I From a terminal
discharging towards
another terminal
600
J From an opening in a car
port (e.g. door, window)
into a dwelling
1200
K Vertically from a terminal
on the same wall 1500
L Horizontally from a
terminal on the same wall 300
Figure 5
X
A
B
C
Figure 6 - Flue connection
A: Vent Terminal
(stainless steel)
B: Weatherproof joint
X= Straight ajustable
between 450 and 790 mm
(stainless steel)
B
A
Balanced flue Gas stove Model. 154 05 06 / 154 05 07
6Technical manual

2.2. Flue connection
The Belfort balanced flue is approved to be vented to
outside through an adjacent exterior wall. The venting
system must comprise of the specified venting
components listed below.
To join the flue sections adopt the following. The
crimped section of the flue should always face outward.
The flue components listed in the above table must be
assembled as shown in the diagram (fig. 6).
When the stove is sited in a corner, the optional
balanced flue elbow 135° must be fitted on the stove
flue outlet (B, fig. 5).
2.2.1. Sealing the flue joints
The flue joints must be weather sealed to prevent
moisture entering the flue system. It is recommended
that the flue joints be sealed with a high temperature
tape, such as aluminium tape (fig. 5).
2.2.2. Vent terminal
The vent terminal must be located in accordance with
BS5440 : Part 1:1990 for natural draught balanced
flues. This standard is summarised in diagram (fig. 4).
Timber framed buildings : When installing the flue in
properties of timber framed construction, the
regulations (BS 5440 : Part 1:1990) must be adhered to.
2.2.3. Post installation checks
Before leaving the appliance connected to the gas
supply, the installer is required to visually examine the
appliance and flueway to ensure that :
-The seal between the combustion chamber and the
room is intact and in good condition.
-The flue has been correctly sealed using the sealing
tape as recommended (rep. 23, p. 13).
-There are no debris contained within the flue
assembly.
-The joint between the terminal and the wall is
weatherproof.
-All pipe work must be purged.
2.3. Ventilation (G.B. Only)
This balanced flue gas stove has no requirement for
additional ventilation in the room (in accordance with
BS 5871 part II).
2.4. Connecting the gas supply
Ensure that the gas supply pipework is capable of
delivering the required volume of gas in accordance
with the relevant British Standards.
Do not make any connections to the appliance until the
pipe work has been purged to expel any dust or debris.
Failure to do this may result in a blockage in the system
that will invalidate the guarantee.
Final connection should be made using 8 mm semi rigid
pipe no more than a metre in length from either ; left or
right utilising the 8 mm elbow supplied.
The gas supply to the stove should terminate with a
standard type safety/restrictor tap.
A gas soundness test must be carried out before
operating the stove.
The 8 mm diameter semi rigid gas inlet pipe should be
connected to the inlet of the gas valve using the nutand
8 mm olive supplied. Support the control whilst finally
tightening the supply pipe. The gas supply to the fire
should be terminated near the fireplace with a safety
type service tap.
2.5. Pressure testing
The gas pressure to the stove must be measured at the
burner test nipple.
-For Propane this is 35.5 mbar measured with the
appliance in the full rate position.
-For Natural gas this is 18,5 mbar measured with the
appliance in the full rate position.
The pressures measured at this point must be equal to
the Burner Pressure as shown in the table on page 3. A
tolerance of +/- 0.5 mbar is allowable.
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 7

2.6. Coals layout
Only the ceramic coals supplied with this appliance are
to be used. The coals should only be laid as shown on
the following pages. Replacement coals and ceramics
are available from your dealer, but should be installed
by a competent person (e.g. Corgi registered).
Please ensure that when fitting the matrix and coals,
that you do not obstruct the pilot.
FRANCO BELGE accept no responsibility for any injury
sustained whilst handling hot ceramics.
Instructions for the layout of the prefixed ceramic
matrix and loose coals for Belfort balanced flue.
Parts : 1 Ceramic mat, 9 Ceramic coals.
Figure 7
-Place the ceramic matrix (rep. 1) above the ceramic
mat, on the supports, onto the top of the burner body.
Figure 8
Place 4 coals on top of the matrix (A) as shown in (B).
Place the remaining 5 coals as shown in (C).
1
2
3
4
1
1
Figure 7 - Fitting the ceramic matrix
1- Ceramic mat (coals support)
2- Burner 3- Burner holes
4- Pilot
A
B
C
Figure 8 - Coals layout
Balanced flue Gas stove Model. 154 05 06 / 154 05 07
8Technical manual

2.7. Service section
2.7.1. Troubleshooting chart
The gas pilot will not ignite or stay lit ? :
•Ensure the gas is turned on at the appliance and the
meter/cylinder.
•Hold in the pilot gas button for at least twenty seconds
once the pilot is alight to ensure the operation of the
safety thermocouple valve.
•Ensure that the pilot injector is not obstructed or
blocked and it is free from any dust or dirt.
•Ensure that the thermocouple has not been damaged
in transit. This is a very delicate electro-magnetic
device.
•On propane, the cylinder could be empty.
The pilot is not burning or performing correctly ? :
•Ensure the pilot flame is the correct size for the type of
gas. The flame should be focused on the thermocouple
probe.
•The pilot flame will have been set correctly in the
factory.
The Main Burner does not seem to be burning
correctly ? :
•Ensure adequate gas pressure to the appliance. The
pressure can be checked by unscrewing the pressure
test nipple and applying a suitable pressure gauge (i.e.
a manometer). Ensure adequate volume of gas is
being used. Once the fire is burning onmaximum, turn
off all other gas appliances in the house and calculate
the fuel being burned from the gas meter.
•Make sure that the burner is burning correctly. The
flame should be fairly evenacross the top of the burner
before any coals are placed on top
Piezo-electric igniter : The spark between the
electrode and the head of the pilot light is not clean;
there is no spark when the lighter is operated.
-Check the contact of the high tension cable of the
spark plug. When the end of the cable is held at about
3 mm from the end of the spark plug, a spark should
be produced when the piezo-elertric igniter is
operated.
-Check that the insulation of the spark plug is not
cracked, and replace the spark plug if necessary.
The thermocouple : When the unit is started up, the
pilot light flame goes out when the handle is turned from
the “ignite” position to the “pilot light” position.
•The thermocouple is notat a high enough temperature,
the pilot light flame is too short.
-Check that the injector (rep. 12, fig. 11, p. 13) is not
partially blocked.
To gain access to the injector, the coals and the burner
must first be dismounted (3 screws).
•Bad contact at the connection of the thermocouple to
the valve.
-Check the tightness of the screw. It should be
reasonably tight.
•Carbon deposit on the end of the thermocouple, which
reduces temperature transmission.
-Clean the end of the thermocouple with emery paper.
2.7.2. Servicing instructions
These instructions are to be used in conjunction with
the normal servicing practices that an installer would
normally use.
-Open the stove door by removing the safety screw
(rep. 1, fig. 9).
-Remove the coals carefully and replace any that are
damaged or broken.
-Clean any deposition of lint off the burner. This can be
done with a soft brush.
-Inspect the burner unit and replace the Ceramic Mat.
-Relay the fire in line with the instructions
“Coals layout”.
-There should be no need to service the burner. If
however this is required, a CORGI registered fitter
should check the setting pressure at the nozzle on the
gas inlet of the burner. The correct pressure required
is stated on the data information plate.
Please explain to the customer the lighting and
extinguishing procedures.
1
23
Figure 9 - Door lock
1: Safety screw
2: 6 mm male spanner 3: Lock
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 9

3.User instructions
WARNING : The combustion chamber of this stove
should only be opened and serviced by a qualified
engineer (eg CORGI REGISTERED)
It is very important to read these instructions
thoroughly before lighting the stove.
3.1. Important Notes
•Ensure that the stove corresponds to the type of gas it
is to be used with. This can be confirmed by checking
the data badge located under the appliance.
•Remember at all times this product is concerned with
high temperatures, and appropriate care should
always be taken.
Fireguard warning
The window and frame on this appliance acts as a
fireguard conforming to BS : 1945 - 1971 and satisfies
the heating appliance (fireguards) regulations 1991.
No part of the window or frame should be permanently
removed.
It does not give full protection for young children or the
infirm.
•Bear in mind that heat given off by the appliance may
affect articles placed close to it. Curtains should not be
positioned above the appliance at a distance less than
12” (30 centimetres) from the top.
•The appliance was not designed to be used as a dryer.
It is therefore not recommended that the appliance is
used in such a manner.
•Under no circumstances should the appliance be
operated with the door open or the door glass
damaged.
•A combustible shelf may be fitted over the appliance
provided that in the case of a 150 mm or less deep
shelf, there is at least 280 mm clearance above the top
of the fire (measured from its highest point).
•Please remember that parts of the appliance become
hot during and after use. If young children, the elderly,
or infirm are likely to be near the stove, ensure a
suitable fire guard (BS6539 or BS6778) is erected.
•Whilst the appliance is called a ‘stove’ the Belfort isnot
designed to be usedin any wayas a cooker. The stove
should not be used for any other purpose than as
a room heater and decorative stove.
•All surfaces except the control knob are considered to
be working surfaces.
3.2. Data information
The data badge is located underneath the appliance.
3.3. Operating the stove
The Belfort balanced flue gas stove operates with a
traditional permanent pilot light.
The knob for ignition and powercontrol is located onthe
right hand side of the stove, under the base plate. It
should be noted that the base plate of the stove may
get very hot, so care should be exercised when
operating the controls.
The pilot light is located at the front of the coal matrix.
If the Pilot Light is extinguished (either by intention or
not), no attempt should be made to re-light until
3 minutes have elapsed.
Important :
ThestovemustalwaysbeignitedintheHIGH setting
(this is when the knob is turned to its extremity in an
anti-clockwise direction) and immediately after lighting,
the stove must be left on maximum setting for five
minutes in order to warm up the flue.
3.3.1. Igniting the permanent pilot light
Figure 10
1 - Depress control knob fully
2 - Whilst depressed, turn knob sharply 90 degrees
anticlockwise to setting (rep. 3, fig. 10). Repeat until
pilot light is visibly lit.
3 - Keep knob depressed at this point for 15 - 20
seconds.
4 - Upon releasing the knob, the permanent pilot light
will be lit, if not return to (1).
3.3.2. Running the stove at a high output
-Ignite permanent pilot as shown above.
-With control knob at ‘PILOT’ setting, turn in an anti
clockwise direction to ‘HIGH’ setting (rep. 4, fig. 10).
-Release the knob. The stove is now burning at its
highest operating output.
Important : Immediately after lighting, the stove must
be left on maximum setting for five minutes in order to
5
3
2
1
4
6
Figure 10 - Control knob and burner test nipple
1- Stop position
2- Ignition device
3- Pilot setting
4- High setting
5- Low setting
6- Burner test nipple
Balanced flue Gas stove Model. 154 05 06 / 154 05 07
10 Technical manual

warm up the flue.
3.3.3. Running the stove at low setting
-With control knob at “HIGH” setting as shown above,
turn in a clockwise direction to “LOW” setting (rep. 5).
-Release the knob. The stove is now burning at its
lowest operating output.
Output can be set at a variable rate between “LOW” and
“HIGH” ; this can be increased by turning the control
knob progressively in an anti-clockwise direction, until
the desired level is achieved.
3.3.4. Extinguishing the stove back to permanent
pilot setting
-From any heat setting, depress control knob fully and
turn clockwise to (rep. 3, fig. 10) position.
-Release.
3.3.5. Extinguishing the stove fully
-From any heat setting or the permanent pilot, depress
control knob fully and turn clockwise to ‘O’ position.
3.4. Safety mechanisms
The BelfortBalanced flue Gas stove (in both natural gas
and LPG), incorporates a number of safety
mechanisms.
3.4.1. Flame supervision device
Since 1st January 1996, under the new European
standard EN5613, all stoves are required to have a
Flame Supervision Device’ (FSD). If the pilot should
become accidentally extinguished, there exists a
potential for a build up of unburned gas. In this situation
the FSD will automatically cut off the gas supply to the
pilot and main burner.
The FSD device works on a thermocouple basis. Next
to the pilot flame on the appliance is a small sensor
containing the thermocouple. This sensor responds to
heat and is linked directly to the gas inlet supply on the
appliance. When lighting the stove, there is a need to
keep the control knob depressed for about 15 - 20
seconds. This allows the thermocouple to reach its
operating temperature. The device will not allow any
gas to enter the burner until the pilot flame has heated
the sensor up to this operating temperature.
If the pilot is extinguished the gas supply will be
automatically cut.
3.4.2. Ignition mechanism
Many gas stoves have electric ignition which requires
mains (240V) supply. This can create problems both
with the presence of water or absence of mains supply.
The Belfort has a Piezo ignition which requires no
external power source. The piezo works on the same
principle as a cigarette lighter, providing a spark when
required.
3.5. Cleaning
Ensure that the stove is turned off before cleaning and
do not attempt to clean if the unit is still hot.
The coals within the appliance are manufactured from
high quality ceramic fibre and should only be arranged
as shown in the coal layout diagram.
After continued use there may be a build up of soot on
the coals which will require removal. Any form of
deposits will reduce the performance of the appliance
and should be removed using a soft brush bya qualified
engineer.
Care should also be taken to ensure deposits do not
enter the vent terminal. If this does occur then cleaning
should be undertaken promptly, and the cause
investigated before further use.
The Belfort Stove is supplied with ceramic coals, which
are to be arranged by the fitter in strict accordance with
the installation instructions. There should be no need
for the purchaser to alter the layout of the coals and it is
recommended that such a practice should be avoided if
at all possible.
Should however any coals become broken during the
cleaning process it is essential that replacements are
purchased and installed by a qualified person (eg Corgi
registered), as there is an optimum number of coals for
a satisfactory functioning of the stove and the flame
picture.
Should any cleaning of the combustion chamber be
necessary, this should be done by a qualified person
(eg Corgi registered). The door should be shut
correctly before use of the appliance.
3.6. Servicing
It is essential that the appliance is regularly serviced
and maintained by a qualified person, the flue system
checked annually.
If the appliance is heavily used it is advisable to
undertake more regular servicing, however under
normal circumstances annual servicing should be
sufficient.
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 11

4.Spare parts
When ordering spare parts, specify the stove type and
serial number, including the colour index, the name of
the part and the partnumber, including thecolour index.
Example :
“Belfort" stove, Ref.: 1540506Y,top352136 EF.
1 100917 ....Campin............ 12x20M7 .....A....B ...C... D....E....F ...G... H... 01
2 105709 ....Biconicalcoupling ........Ø4.......A....B ...C... D....E....F ...G... H... 01
3 110404 ....Hingepin .............6x30.......A....B ...C... D....E....F ...G... H... 02
4 113105 ....Malespanner.....................A....B ...C... D....E....F ...G... H... 01
5 122204 ....Wingednut ...........diam.8......A....B ...C... D....E....F ...G... H... 01
6 122426 ....Nut ..........................A....B ...C... D....E....F ...G... H... 01
7 122427 ....Nut ..........................A....B ...C... D....E....F ...G... H... 01
8 122701 ....Nut ..........................A....B ...C... D....E....F ...G... H... 01
9 124373 ....Electrode .......................A....B ...C... D....E....F ...G... H... 01
10 124412 ....Strut..........................A....B ...C ... D....E....F ...G... H... 01
11 134258 ....Bushing........................A....B ...C... D....E....F ...G... H... 01
12 139596 ....InjectorLPG ..........18/120...........B ...................F ...G... H... 01
12 139597 ....InjectorNG ........... 18/280......A.........C ... D....E................... 01
13 139615 ....InjectorLPG ..........................B ...................F ...G... H... 01
13 139610 ....InjectorNG......................A.........C... D....E................... 01
14 142301 ....Adhesiverope ....................A....B ...C... D....E....F ...G... H..0,87m
15 142429 ....Gasket ........................A....B ...C ... D....E....F ...G... H... 01
16 142437 ....Gasket ........................A....B ...C ... D....E....F ...G... H... 01
18 159014 ....Testnipple ......................A....B ...C... D....E....F ...G... H... 01
19 162569 ....Descriptiveplate ...................A.........C ... D....E................... 01
19 162570 ....Descriptiveplate ........................B ...................F ...G... H... 01
20 164329 ....Biconicalcoupling .......diam.4......A....B ...C... D....E....F ...G... H... 01
21 166745 ....Gasvalve+piezo ..................A....B ...C... D....E....F ...G... H... 01
22 179225 ....Thermocouple ....................A....B ...C ... D....E....F ...G... H... 01
23 181614 ....Ceramicrope.......... d.9,5 ......A....B ...C... D....E....F ...G... H..1,92m
24 181615 ....Ceramicrope...........d.12.......A....B ...C ... D....E....F ...G... H..1,85m
25 142316 ....Gasket ..............7x3.......A....B ...C ... D....E....F ...G... H..1,19m
26 187114 ....Doublecoupling ........diam.8......A....B ...C... D....E....F ...G... H... 01
27 188318 ....Pilot..........................A....B ...C... D....E....F ...G... H... 01
28 188798 ....Glass ..............267x205......A....B ...C ... D....E....F ...G... H... 01
29 189825 ....Screw...............M5x6 ......A....B ...C... D....E....F ...G... H... 01
30 189849 ....Screw.............. M6x16 ......A....B ...C... D....E....F ...G... H... 01
31 236007 ....Controlplate .....................A....B ...C... D....E....F ...G... H... 01
32 259015 ....Fixingplate......................A....B ...C... D....E....F ...G... H... 04
33 269426 ....Deflector .......................A....B ...C... D....E....F ...G... H... 01
34 276006 ....Plate..........................A....B ...C ... D....E....F ...G... H... 01
35 300118 MJ..Leg ......................................... D..............G........ 04
35 300118 MK..Leg ...............................................E.............. H... 04
35 300118 EF..Leg ..........................A........................................ 04
35 300118 79 ..Leg ...............................B ...C ..............F ............. 04
36 300484 ....Base..........................A....B ...C... D....E....F ...G... H... 01
37 301541 MJ..Doorlock ...................................... D..............G........ 01
37 301541 MK..Doorlock ............................................E.............. H... 01
37 301541 EF..Doorlock .......................A....B .................................. 01
37 301541 79 ..Doorlock .................................C ..............F ............. 01
38 303718 MJ..Blankingplate.................................... D..............G........ 01
38 303718 MK..Blankingplate..........................................E.............. H... 01
38 303718 EF..Blankingplate.....................A....B .................................. 01
38 303718 79 ..Blankingplate...............................C..............F ............. 01
39 303871 EF..Fluecollar.......................A....B ...C... D....E....F ...G... H... 01
40 306268 EF..Backwall .......................A....B ...C... D....E....F ...G... H... 01
41 307437 EF..Fuelretainer .....................A....B ...C... D....E....F ...G... H... 01
42 309886 MJ..Frontplate ..................................... D..............G........ 01
42 309886 MK..Frontplate ...........................................E.............. H... 01
42 309886 EF..Frontplate ......................A....B .................................. 01
42 309886 79 ..Frontplate ................................C ..............F ............. 01
43 309997 MJ..Maindoor...................................... D..............G........ 01
43 309997 MK..Maindoor............................................E.............. H... 01
43 309997 EF..Maindoor.......................A....B .................................. 01
43 309997 79 ..Maindoor.................................C ..............F ............. 01
44 310725 MJ..R.sidepanel .................................... D..............G........ 01
44 310725 MK..R.sidepanel ..........................................E.............. H... 01
44 310725 EF..R.sidepanel .....................A....B .................................. 01
44 310725 79 ..R.sidepanel ...............................C ..............F ............. 01
45 310823 MJ..L.sidepanel .................................... D..............G........ 01
45 310823 MK..L.sidepanel ..........................................E.............. H... 01
N° Code ....Description............Type.......A....B ...C ... D....E....F ...G... H...Qty
* Colour index
A: 154 05 06Y = *EF B: 154 05 07Y = *EF
C: 154 05 06J = *79 D: 154 05 06K = *79
E: 154 05 06C = *MJ F: 154 05 07J = *MJ
G: 154 05 07K = *MK H: 154 05 07C = *MK
Balanced flue Gas stove Model. 154 05 06 / 154 05 07
12 Technical manual

65
66
35
35
35
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21 22
23
24
25
27
28
29
30
31
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59 60
3
23
23
63
26
47
54
32
63
25
25
25
63
63
25
63
62
64
Figure 11
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 13

45 310823 EF..L.sidepanel .....................A....B .................................. 01
45 310823 79 ..L.sidepanel ...............................C..............F ............. 01
46 315608 ....Airduct ........................A....B ...C... D....E....F ...G... H... 01
47 325304 EF..Reducingplate....................A....B ...C... D....E....F ...G... H... 02
48 327801 ....Clamp.........................A....B ...C... D....E....F ...G... H... 01
49 327902 MJ..Tray......................................... D..............G........ 01
49 327902 MK..Tray...............................................E.............. H... 01
49 327902 EF..Tray..........................A....B .................................. 01
49 327902 79 ..Tray....................................C..............F ............. 01
50 352136 MJ..Topplate ...................................... D..............G........ 01
50 352136 MK..Topplate ............................................E.............. H... 01
50 352136 EF..Topplate .......................A....B .................................. 01
50 352136 79 ..Topplate .................................C ..............F ............. 01
51 465015 ....Pilotline........................A....B ...C... D....E....F ...G... H... 01
52 467527 ....Testline........................A....B ...C... D....E....F ...G... H... 01
53 467529 ....Pipe..........................A....B ...C... D....E....F ...G... H... 01
54 974600 60 ..InjectorsupportNG..................A.........C ... D....E................... 01
54 974601 60 ..InjectorsupportLPG......................B ...................F ...G... H... 01
55 982634 ....Pipe..........................A....B ...C... D....E....F ...G... H... 01
56 109723 ....Ceramiccoals.......... (LF5) ......A....B ...C... D....E....F ...G... H... 05
57 174651 ....Coalsupport .....................A....B ...C... D....E....F ...G... H... 01
58 905917 ....CompleteburnerNG.................A.........C... D....E................... 01
58 905919 ....CompleteburnerLPG .....................B ...................F ...G... H... 01
59 905916 ....BurnerNG ......................A.........C... D....E................... 01
59 905918 ....BurnerLPG...........................B ...................F ...G... H... 01
60 142436 ....Gasket ........................A....B ...C... D....E....F ...G... H... 01
61 178067 ....Ventterminal.....................A....B ...C... D....E....F ...G... H... 01
62 109724 ....Ceramiccoals..........(LF13)......A....B ...C... D....E....F ...G... H... 04
63 181606 ....Ceramicrope.......... 10x4 ......A....B ...C... D....E....F ...G... H..3,67m
64 158230 ....Controlplate .....................A....B ...C ... D....E....F ...G... H... 01
65 988861 ....Completedoor ....................A....B .................................. 01
65 988862 ....Completedoor ..............................C..............F ............. 01
65 988863 ....Completedoor ................................... D..............G........ 01
65 988864 ....Completedoor .........................................E.............. H... 01
66 161027 ....Touch-uppaint ..............................C..............F ............. 01
66 161026 ....Touch-uppaint ................................... D..............G........ 01
66 161032 ....Touch-uppaint .........................................E.............. H... 01
Balanced flue Gas stove Model. 154 05 06 / 154 05 07
14 Technical manual

Notes
Model. 154 05 06 / 154 05 07 Balanced flue Gas stove
Technical manual 15

❧Warranty certificate ❧
❧Legal warranty
Our products are guaranteed for twelve months against any
defect, flaw or imperfection. During this time, all parts judged
defective by our Warranty control department may be
replaced in our workshops. Incidental costs of transportation
and packing payable by the buyer.
Some parts or components have a longer warranty period :
- Cast-iron shell of boiler : 3 years
- Steel shell of boiler : 3 years
- Removable or independent stainless steel hot water
cylinder : 5 years
- Independent enamelled steel hot water cylinder : 3 years
- Incorporated circulating pump : 2 years.
❧Terms of the warranty
Thiswarrantyisonlyvalidif:
- The unit has been installed and checked by a professional
installer before operating,
- All installation and adjustment instructions listed in the
technical manual supplied with the unit have been followed,
- All operation and maintenance instructions have been
followed.
❧This warranty does not cover :
- Lamps, fuses, spark plugs, cast iron parts directly in contact
with burning coal and wood, firebricks, flue baffles, glasses .
- Any damage resulting from the use of fuel not
recommended in our instructions ;
- Parts which are damaged by external causes such as
unadapted chimneys, thunderstorms, damp, faulty pressure
or fail in pressure, thermic anomalies, explosions, etc...
- Electrical parts which are deteriorated by any connection or
use on a supply circuit with voltage within 10% of the indicted
voltage (230 V in EU).
Material subject to modifications without prior notice. This
manual does not engage the responsibility of
FRANCO BELGE.
* Nameandaddressoftheinstaller: _____________________________
______________________________________________
( Telephone:_______________________________________
* Nameandaddressofthecustomer: ____________________________
______________________________________________
Dateofinstallation: ____/____/________
Model of the appliance :
Color :
Serial number : ___ ___ ___ ___ ___ ___
• This certificate has to be completed and kept carefully.
In case of claims, send a copy of this to :
Les Fonderies Franco-Belges, rue Orphée Variscotte, 59660 MERVILLE, FRANCE.
❑154 05 06 ❑1540507
❑Y❑J❑K❑C